-
Product
7 Round Pin Tractor Trailer Circuit Checker / Maintenance Kit
#8029
-
Innovative Products of America
Test, clean and restore 7 round pin connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 7 round connectors. Tests tractor electrical circuits Removes corrosion from truck and trailer connectors Enhances electrical contact points Extends harness life Use as a pin wear gaugePatentedKit Includes: #7865L: 7 Round Pin Tractor Trailer Circuit Checker, #8024: 7 Round Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
Product
Leak Detection Oil
-
The faster, safer and easier way to locate even tiny leaks in industrial air conditioning and refrigeration systems. Lumirati® bottled dyes can be poured directly into any AC&R system. The dye can remain safely in the system to confirm repairs and perform future preventive maintenance checks. Lumirati® Leak Detection Oil is the only dye that gives you all these benefits:- Universal dye that is compatible with all refrigerants and lubricants- OEM-approved by major compressor, refrigerant, lubricant and AC&R equipment manufacturers- Co-solvent free so dye will not impair lubricant properties, which could lead to excessive wear or damage to the system components
-
Product
Noise & Vibration Measurement Systems
BK8600
-
Rotation can produce noise and extraneous vibration for any number of reasons and could cause wear, discomfort, or other problems. The BK8600 series of testers are specially designed to test for these.
-
Product
Friction and Wear Tester
EFM-III Series
-
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
-
Product
Medical Masks Flammability Tester
TF361
-
TESTEX Testing Equipment Systems Ltd.
Medical Masks Flammability Tester is used to test the flammability of medical masks, to ensure the safety of masks to wear in. Medical Masks Flammability test Chamber complies with EN 149, GB 2626, GB 19083.
-
Product
Torque Tester
TorqueLab® LTT-Series
-
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained.
-
Product
Hardness & Scratch Resistance
-
Hardness can be defined as a material’s resistance to permanent deformation. In the coatings industry, hardness measurement can be used to determine the resistance of the coating to scratching from general wear and tear and also if a coating is fully cured.
-
Product
CMP Tester
CP-6
-
The state of the art Rtec CMP tester CP-6 allows to study and characterize CMP process like never before. In addition to polishing wafers & substrates the tester comes with inline surface profilometer. This combinations sheds information on why and how the surface, friction, wear etc. changed. Tester also measures several inline parameters such as friction, surface roughness, wear volume etc. to understand the process in detail.
-
Product
Noise Activated Warning Signs
-
Signs within the workplace that warn of high noise levels are common place as they help ensure that employees, visitors and the public are aware and, if required, wearing ear protectors. This type of signage is ideal when noise levels are stable and consistent.
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
High Speed Test Bench
AT444
Test Platform
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
-
Product
Tribometer
-
NANOVEA Tribometer is a powerful and adaptable all-in-one friction and wear tester with the widest range of testing and environmental modules on the market. The simple design of a NANOVEA Tribometer allows for fast interchangeability to accommodate for any research need and requirement or standard.
-
Product
PXI Dual 4 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-882-002
Multiplexer Module
This PXI multiplexer exhibits low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40-882 MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
Product
High-pressure environmental friction and wear tester
-
This testing machine is used to evaluate the frictional characteristics in a pressure container. It can evaluate the frictional characteristics of refrigerants, oil, friction materials, etc. for compressors and so on. It has a load cell inside the pressure container to enable frictional-force measurement with high accuracy.
-
Product
Automatic Calibration Module
ACM2509
-
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to seven connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
Charge Plate Monitor
-
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
Product
RF Safety Monitoring
MVG EME Guard Plus
-
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
-
Product
ICP-OES Spectrometers
-
ICP-OES spectrometers measure the concentration of elements from ppb to % using de-excitation of atoms and ions in a plasma. The robustness of our Ultima ICP spectrometers makes them ideal for applications common to mining, chemicals manufacture, salt production, wear metals in oil analysis, petrochemical, metallurgical production and precious metal refining.
-
Product
Racing Tire Hardness Tester
52-50553
-
Longacre Racing Products, Inc.
Tire hardness has a huge affect on your car's performance. A tire too hard won't bite and a tire too soft may wear quickly or even ball up. Also tire hardness changes during its life cycle. To run your best you must keep track of all your tire's hardnesses.
-
Product
Industrial Vibration Sensor
IVS-500
-
The new IVS-500 Industrial Vibration Sensor is the key to fast acoustic quality inspection, structure-borne noise analysis and reliable pass-fail decisions. This Laser sensor measures reliably, in demanding industrial environments, without contact and therefore without wear and on virtually all surfaces. Costs and yields are therefore optimized by reducing false rejects in the production and assembly process. The simple setup and ruggedized sensor design of the IVS-500 enable a smooth integration into production test systems. Complemented with the software tool QuickCheck, Polytec offers a comprehensive solution for reliable pass/fail analysis.
-
Product
Non-contacting Position Sensors
-
For use in harsh environments, Vishay offers non-contacting position sensors based on Hall Effect technology. Linear displacement, rotational (single- and multi-turn), and kit design options all provide a full 360° measurement range with no dead angles and very long life, since there is no wear and tear on sensor elements. Applications for Vishay’s non-contacting position sensors include any system where vibration, shock, or dithering is to be expected, such as embedded applications in vehicles.
-
Product
Metalex Flow Sensor
525
-
The Signet 525 Metalex Paddlewheel Flow Sensor combines stainless steel construction with insertion paddlewheel technology. The result is a highly reliable sensor resistant to extreme pressures and temperatures. The Tungsten Carbide shaft with carbon fiber-reinforced PTFE bearing provides excellent wear resistance for extended service.
-
Product
6, 8 GHz, 4 Channel Programmable Attentuator
QPA8, PA8
-
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA8 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly. Attenuation is controlled in standard steps of 0.0625 dB. The 10 bit programmable range results in the full 210=1024 steps yielding a dynamic range of 0 to 63.9375dB. Non-standard custom step sizes are available.
-
Product
Sliding Peel Strength Tester
OST3000
-
Compared to the scratch test, the friction and wear test is considered to be a durability evaluation method that is closer to the actual situation
-
Product
Digital Tire Pressure Gauge 230 PSI
AstroAI ATG230
-
Green Backlit LCD display and flashlight for visibility in dimly light areas, easy-to-read digits help you easily measure your vehicle's tire pressureHeavy Duty Stainless Steel Made And RV/Truck Special Designed to maintain correct tire pressure, reduce tire wear and extend tire life; Digital display reading instantly and clearly being shown, no longer do the guesswork of analog gaugesBi-directional push-pull (Dual) head design; Nozzle easily forms a seal with the valve stem giving quick and accurate readings in 0.1 increments; 4 settings with longer range: 0-230 PSI / 0-16 Bar / 0-16 Kg/cm2 / 0-1585 Kpa
-
Product
Mechanical Tester
-
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
Product
Meter Test Bench
-
Meter Test Banch is available with high-technology to ensure high testing accuracy as well as maximum functionality. It is designed to provide precise results in any simple to complex testing. It comes with modern systems to ensure to provide artificial load that cannot be changed in the power supply. It is provided with high durability and efficacy to ensure long lasting life with no maintenance. In addition to this, it ensures high accuracy in testing without any wear.
-
Product
Bearing friction and wear tester
-
This testing machine evaluates the frictional characteristics of radial bearings. The circuit system adopted for the lubricant enables heating up to 80C.
-
Product
ICI Mace Snag Tester
-
TESTEX Testing Equipment Systems Ltd.
ICI Mace Snag Tester, to determine the tendency of fabrics to snag (pull yarn loops from fabric) in normal wear (mace snag). ICI Mace Snag Tester complies with ASTM D3939, etc. Please contact us for more information about snagging test.
