Filters
Electronic circuits which refine signal by blocking certain frequencies, while allowing other frequencies to pass.
See Also: Filter / Amplifiers, EMI Filters, Low Pass Filters, Programmable Filters, Attenuators
-
Product
Solid State Broadband High Power Amplifier
Model 2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
Product
Sound Level Logger-limiters
-
Frequency Filter Sound Level Limiter-recorder that controls by emission Sound Pressure Level or reception SPL.
-
Product
16 SE Or 8 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-16-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
Fanless Desktop Network Appliance Platform With Intel® Celeron® Processor N3350 1.10 GHz And 3 GbE LANs
NA345E
-
The fanless NA345E adopts the low-power consumption Intel® Celeron® processor N3350 (codename: Apollo Lake). It aims to provide small business and SOHO customers an energy-saving and cost-effective network appliance for solutions in VPN, content filtering, UTM, network security gateway, and firewall. The desktop NA345E supports one non-ECC DDR3L-1866 SO-DIMM socket providing system memory of up to 8GB; moreover, it offers one mSATA for storage. It is equipped with three 10/100/1000 Mbps LAN ports (Intel® i211 Ethernet controller). The network appliance platform also has two USB 3.0 ports and an RJ-type serial console port. The system features a watchdog timer for reliable operation. Additionally, it supports Linux operating system.
-
Product
Passive Components
-
Focusing on frequency control products, electromagnetic interference (EMI/RFI) filters, and resistive components (potentiometers/encoders).
-
Product
Remote Monitor Management Information Base
SNMP RMON MIB
-
For every control table in the MIB, create and delete rows with various combinations of SNMP requests (all variables in a single request throughall variables in individual requests).Determine which row of this table is modeling the ethernet interface connected to the agent (requires that we are using ethernet). Check that this is for the same interface discovered in the "interfaces" test. Check counters.Build a history control row pointing to the interface connected to the agent. Check validity and traffic reported.Test agent's ability to generate an alarm on an RMON variable, then on threshold condition. Test for support of alarms on failing events, and in the event of target variable vanishing.Set up agent to track hosts on the ethernet interface connected to the agent. Check that entry was added for Rmon device's own ethernet address.Generate various top N reports (hostTopN test) and check validity.Start a matrix capture and check that the src-dst and dst-src tables are in sync.Check a channel and check for event generation (filter test).Create a channel and start a capture. Test locking and wrapWhenFull operation.
-
Product
Single Channel USB Programmable High-Pass Filter
USBPHP-S1
-
The USBPHP-S1 stand alone USB controllable module provides a single channel of high pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPHP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPHP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPHP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
6U High Performance Data Acquisition subsystem
CPCI-AD320
Data Acquisition Module
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8320-6U can also accept external scan and trigger signals from a front panel connector.
-
Product
PXI Sound and Vibration Module
Sound and Vibration
PXI Sound and Vibration Modules are designed specifically for applications like audio test and measurement, noise and vibration diagnostics, machine condition monitoring, automotive test, noise, vibration, and harshness(NVH) analysis, and laboratory research. They provide software-configurable AC/DC coupling, antialiasing filters, and IEPE conditioning to ensure precision measurements with microphones, accelerometers, and other transducers with large dynamic ranges.
-
Product
Adjustable Bandwidth Tunable (700MHz-1000MHz)
MFA R&D Tunable
-
Allows passband centered at any frequency over tuning range while adding the capability to vary passband width. Upon input of desired frequency and bandwidth, the filter tunes center frequency and adjusts bandwidth to provide a custom filtering solution on demand. 1dB bandwidth of 5MHz to 20MHz. Suitable for LTE and other test applications.
-
Product
OEM Module For Conversion Between IP And ASI
DTM-3200-RA
-
The DTM-3200 converts IP to ASI, or ASI to IP. Integrate this compact module to extend the range of I/O standards supported by your product. Technical highlights include advanced IP-jitter filtering, ultra-low latency and zero-jitter IP transmission.
-
Product
Multi-channel low-pass filter board
AAF-2
-
The AAF-2 is a multi-channel low-pass filter board designed for use in front of A/D converters with resolution up to 16-bits. It is ideal for filtering applications in sound and vibration testing, ultrasonics, acoustics, structural analysis, industrial, test, scientific and laboratory data collection and applied mechanical applications in electronics, aerospace, field research, automotive, and process control industries.
-
Product
CANOpen Analyzer
CapAnalysis
-
CapAnalysis is a Web pcap file Viewer. It can manage not only one file, but sets of pcap files. Deep Packet Inspection (DPI): more than 140 protocols. Filtering the captures analized. Open Source
-
Product
Partial-discharge Detection System
GDYT Series
-
GDYT series include partial discharge power frequency testing transformer(YDTW),partial discharge detector(GDJF2008),Isolation filter frequency doubling power device(GDSF-81G) and power frequency withstand voltage control table(GDYD table).It widely used in electrical manufacturing,power operation departments, research institutes and universities.
-
Product
SparkFun FM Tuner Basic Breakout
Si4703
-
This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.
-
Product
Three-State Kalman Filter Algorithm
A6-1PPS
-
The A6-1PPS uses a three-state Kalman filter algorithm to measure and correct the frequency offset of the oscillator with respect to the 1pps input.
-
Product
Water Quality and Temperature Checker
-
Drinking clean water is always good for your health. So, make sure you always drink good quality water. Regular check to ensure the performance of your water or water filter. The lower the TDS level in the water, the more efficiently your body cells actually get hydrated by the water you drink.
-
Product
Energy Probes
RjP-400 Series
-
The RkP-400 Series probes consist of a compact detector assembly, or head, and a preamplifier housed in a separate enclosure. The external dimensions of all the 400 Series Probes are the same, with identical detector planes, allowing for easy interchange of probes in an experiment. The heads have both ¼-20 and M6 tapped holes, a built-in 1" (25mm) filter holder, and a side-mounted BNC connector. Probe specific data, including spectral response curves and calibration dates, is stored in the preamplifier for access by the instruments.
-
Product
YIG Oscillators
-
With a 30 year heritage in YIG technology, Teledyne RF & Microwave has unsurpassed capabilities as your single source for YIG Oscillators and offers 'best in industry' low phase noise. Teledyne has a large, self-contained YIG manufacturing and R&D infrastructure that ensures continuous YIG innovations, including the industry's only YIG filter that "locks" to a desired signal.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
PXI-5124, 150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope
778757-01
Oscilloscope
150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope—The PXI‑5124 high-resolution PXI oscilloscope samples up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth. The PXI‑5124 also features PXI synchronization and data streaming capabilities.
-
Product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
-
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
Product
MIL-STD-1553 A / B Test And Simulation VXIbus Module
VXI-1553
-
*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
Harmonic Filter Resistors
-
The widespread use of nonlinear loads such as power electronics based equipment and electric arc & ladle melt furnaces all around the world hinder the quality of electric power. One of the most important parameters for defining the power quality is harmonic distortion.
-
Product
Rectangular Connectors
-
Smiths Interconnect offer a broad range of modular and rectangular connectors. Our modular solutions allow the user to customize, configure and combine signal, Power, Filter High Speed Data (coax, twinax, triax, quadrax, fiber optic) contacts into a single connector.
-
Product
64-Channel VME Analog Input Module
V230
-
The V230 provides high channel-count data acquisition for dense monitoring applications. The 64 channels are individually programmable for both input range and filtering. The three input ranges slightly exceed ±10 V, ±1 V, and ±100 mV, allowing confident measurements all the way to the end of common signaling ranges.
-
Product
Adapter/Stainless Steel
WADP-24M24F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
RF Training Kit And Lab Sheets
Y1800A
-
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
-
Product
Automation
50 Hz Adaptive Filter
-
One of the main causes of the reduction of accuracy in low frequency signal parameters measurements is the influence of artificial and natural electromagnetic interferences on measuring channels of measuring tools (MT). Under laboratory, production and natural conditions, the main interference is 50 Hz network interference. To eliminate this interference, ZETLAB software package uses a program providing a 50 Hz band-stop filter.
-
Product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCIe-7256
Analog Output Module
ADLINK's PCIe-7256 features all Form C type relays, ideal for device connection with on/off control. With latching relays, the PCIe-7256 further provides operating power conservation, while the status of each latching relay output is indicated by onboard LED. When the relay is in SET, its corresponding LED lights. Latching relays also feature unchanged status even when the system powered off, making the PCIe-7256 suitable for critical applications requiring output status to be maintained even under fault conditions. All digital input channels are non-polar and optically isolated, and may be set for optional use of RC filter. The PCIe-7256 also features a change-of-state (COS) function generating interrupt when any digital input changes state.
