Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-135
The 40-297A-135 (PXI) and the 42-297A-135 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 201 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Environmental Monitoring Systems
Eurotech environmental monitoring systems are designed to provide a scalable, efficient and compact solution that integrates multiple sensors in a single, easy to deploy unit. These compact, easy to install environment monitor systems collect and analyze air quality parameters, electromagnetic fields, ionizing radiation levels and sound pollution.
-
product
Miniature Camera Modules
The NanEye miniature CMOS image sensors and corresponding camera module configurations are available in modular form factors as small as 1 mm x 1mm. Various optics options are available.
-
product
Sensor Tester
*Connection facilities for DC 2-wire and 3-wire sensors, *Change in switching status signalled visually and acoustically, * 15 V operating voltage for sensors when using a 9 V block battery, * Switches off automatically when not in use, * Visual indicator for operating voltage, switching status and low battery
-
product
Sensors
To measure machinery or structural vibration, a transducer is needed to convert the mechanical motion into an equivalent electrical signal. Each sensor has distinct advantages in certain situations and limitations in other, so it is important to select the most suited transducer or sensor for your job. Equally, important is selecting the appropriate parameter of vibration amplitude for measurement. IRD® has a wide range of transducers and accelerometers available to help you obtain accurate, reliable data, whether your concern is vibration monitoring, analysis, or dynamic balancing.
-
product
PXI BRIC8 FIBO Matrix Dual 140x4 3pin brkout
40-592A-107
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Resistance Temperature Sensors
Watlow Electric Manufacturing Company
These sensors are suited for applications where accuracy and stability are essential for proper control in applications that operate at or below 1200°F (650C).
-
product
PRO Test Lead Kit
142
#142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.
-
product
Data Acquisition Systems
Includes measurement devices, sensors, a computer, and data acquisition software.
-
product
Averaging Clip-on Extensometer
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
product
10-CH Pneumatics CAN
YAV90PNE
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
product
Electronic Multifunction Data Loggers
The DeltaTrak Electronic Data Logger is a portable, pocket sized electronic device powered by a 10-year lithium battery. It is designed for easy and reliable tracking of parameters such as temperature, relative humidity, electric current, pressure, process signals, and pulse signals. All data loggers have a built-in temperature sensor plus single or multiple external channels where different sensors can be attached for remote monitoring of a variety of parameters. The DeltaTrak Data Loggers inte...show more -
product
Speed Switches & Sensors
Monitor Speed and Detect Motion of Conveyors and Other Rotating Apparatus for Premium Protection of Expensive Belting and Equipment
-
product
USB Power Sensor - 100 MHz to 20 GHz, Average, Peak (Pulse), Pulse Profile
GT-8555B
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
product
PXI BRIC4 FIBO Matrix Dual 40x4 3pin brkout
40-592A-002
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Humidity Sensor Components
Based on a unique capacitive cell, our temperature and humidity sensors are designed for high volume applications where humidity measurement is needed.
-
product
Traffic Sensors
TE Connectivity (TE) offers complete solutions and installation support for RoadTrax BL piezo sensors and QL series weigh-in motion traffic sensors.
-
product
Oxygen Bomb Calorimeters
Labodam oxygen bomb calorimeters are designed with high precision sensors and microprocessors to get reliable and accurate results. They are designed and made as per the International Standards ASTM D5865-13 Test Methods for Heat of Coal, ASTM D240-17 Test Methods for Calorific Value of Petroleum Products, and ASTM D4809-13 Oxygen Bomb Calorimeter.
-
product
PXI Precision Resistor Module, 4-Channel, 2 to 6.97k
40-297-130
This 4-channel PXI precision resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Wind Speed and Wind Direction Sensors
Wind vanes measure wind direction and are often used with anemometers, which measure wind speed. Campbell Scientific offers a variety of anemometer designs: cup, propeller, ultrasonic, sonic, and lidar. Most of our wind sensors are modified slightly from the manufacturers’ stock items so that they may be used with our dataloggers in research, air quality, and general purpose meteorological applications.
-
product
Wastewater Samplers – Stationary
The ECD Analyzers range of automatic stationary, refrigerated wastewater samplers consists of three models, the AQUAS200, the AQUA-S320 and the rugged outdoor AQUA-S320H. At the heart of each is the well proven AQUA Sampling Module, a robust and reliable unit proven in thousands of applications worldwide and trusted by users as diverse as food manufacturers, water companies and the Environment Agencies. The air pump vacuum sampling system featured within the AQUA Module provides for an extremely...show more -
product
Gas Monitors with X3® Technology
Ultima® X
The Ultima X Series Gas Monitors with X3 Technology bring the power of multi-sensing, signal boost and ModBus output to the Ultima X line of MSA gas monitors. The units are crafted from either stainless steel or NEMA 4X-rated plastic, and our patented SafeSwap sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification.
-
product
Wireless Gateways
Networked Communication Solutions, LLC
Allows your NCS wireless sensors to communicate with the NCS Online Wireless Sensor Monitoring and Notification System.
-
product
Balance Thermocouple Power Sensor, DC To 18 GHz
N8481S
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
product
sbRIO-9235, Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781579-01
Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9235 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9235 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
product
Accessories
Accessories allow the user of a vibration sensor to integrate them into their machine monitoring systems ensuring that:- The sensor mounting is correct- Connections and cables are right for the job and environment- Remote measuring points are convenient- Calibration of sensors and measuring systems can be confirmed in the field
-
product
Radar solutions for the metal & steel industry
Our reliable radar sensors enable the high-precision width measurement and thickness measurement of semi-finished metal, the contactless level monitoring of molten metal and the steel strip positioning in the coating line.
-
product
4-20mA Sensor Converter
ENVIROMUX-S420MA-24V
External RJ45 device monitors up to two 4-20 mA analog sensors. Supports ISA Type 2, ISA Type 3, and ISA Type 4 sensors. Provides 24VDC, 25mA for each sensor. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 500 ft. (152 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: RoHS.
-
product
Industrial Current Sensors
RCT
Power Electronic Measurments Ltd
The RCT range of AC current transducers are designed for permanent or semi-permanent installation and are available with industry standard outputs.