Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
ATEX-Compliant IR Temperature Sensors
FLIR A310 ex
Explosive atmospheres need to be protected from ignition sources. Selecting equipment and protective systems which meet the requirements of the ATEX Product Regulations or similar regulations is essential. FLIR A310 ex is an ATEX compliant solution, with a thermal imaging camera mounted in an enclosure, making it possible to monitor critical and other valuable assets also in explosive atmospheres. Typical applications for the A310 ex include process monitoring, quality control, and fire detectio...show more -
product
Interface Units
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
product
VIS-SWIR FPA's
Imaging electronic sensors sensitive in visible, near infrared, short wavelength infrared spectral bands that generate two dimensional electronic images have found mass applications in industry, defense, security, science, environmental protection, medicine etc. Imaging sensors sensitive only in VIS/NIR range are almost exclusively silicon chips manufactured using a series of technologies: CCD, CMOS. ICCD, EMCCD, EBAPS, sCMOS in color or monochromatic versions. Color VIS/NIR sensors are sensitive to light only in visible range when monochromatic VIS/NIR sensors are sensitive up to about 1000nm.
-
product
PXI Precision Resistor Module 9-Channel, 2 to 13.6k
40-297-031
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Moisture Testers for Wood
Here you will find a moisture tester for wood to determine absolute moisture in different wood types. Newly-cut logs can have a moisture content of 80% or more, depending on the type. Since wood shrinks substantially when dried, it must be dried before being used in construction or most other applications. This is most often done using a large furnace called a kiln. The air drying method may also be used, but this is much slower. With the help of the moisture tester for wood you will be able to ...show more -
product
Miniature Piezoelectric Accelerometers
Structured with highly sensitive piezoceramic sensing elements, miniature Ceramic Shear ICP® Accelerometers have an excellent signal-to-noise ratio, high measurement resolution, and are ideal for conducting low-level vibration measurements. Due to their inherent higher sensitivity, a ceramic ICP® accelerometer can be assembled with a smaller mass than comparable quartz units, resulting in a sensor that is lighter in weight, has a higher frequency response, and has a lower noise floor. To furt...show more -
product
SENSOR FOR THICK & CURVED MATERIALS
S3
The smallest, simplest, most affordable high-precision non-contact sheet resistance sensor availableNon-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterReads any conductive coatingon even the thickest nonconductive substratesOptions include PC-based productivity software, stage, and morePerformance limited by "lift off" phenomenonelevation of sensor above conductive layer must be carefully controlled
-
product
Flow Sensors
They're designed to measure air, oxygen, and other gases for embedded applications. The compact size and standard configurations make it easy to design them into your products.
-
product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
product
Programmable Data Logger
HD32MT.1
Programmable datalogger able to capture and store the values measured by a series of sensors connected to its inputs. 8 analoge input, 8 digitale input, 2 puls input, potential free contacts, alarming. Programmable through software. RS485, RS232.
-
product
Relative Humidity Outdoor, Indoor Probe
T1110
Only relative humidity output 4-20mA.Also available with direct temperature RTD Pt1000 sensor output.Other sensors on request.
-
product
PXI BRIC8 FIBO Matrix Dual 100x4 3pin brkout
40-592A-105
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Calibration Hangers And Weights
Calibrated Dead Weight are the official means by which torque analyzers and torque sensors are calibrated and are traced to National or International Standards, such as N.I.S.T, ISO and others. Many industries like as medical, aerospace, nuclear and others continuously calibrate their measuring equipment to comply with government regulations. For companies that prefer to have calibration capabilities in-house when their calibration requirements become extensive, they need calibration equipment.
-
product
Load Cells
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
product
Sensors
Magneto-Optical Sensors (MO Sensors)
The highly sensitive magneto-optical (MO) sensors form the basis for visualizing magnetic fields in production and research.
-
product
A²B® Automotive Audio Bus Solution
ITD 1024
ITD 1024 is an off-the-shelf solution for A²B®, an emerging automotive audio bus. In combination with a comprehensive set of software tools, ITD 1024 allows rapid testing of various A²B® components such as audio speakers, amplifiers, microphone arrays, sensors, and actuators.
-
product
FBG-Scan 700/800
FBG-Scan 700/800
The FBG-Scan 700 and 800 are dynamic, high precision measurement devices for Fiber Bragg Grating (FBG) sensors. The system can measure up to 40 FBG sensors using 2 input channels. Both input channels are simultaneously monitored using an optical coupler at a scan rate up to 2000Hz.
-
product
Sub-Miniature ICP® Pressure Sensors
PCB's sub-miniature 105C dynamic pressure sensors are specifically designed to fit into tight spaces where mounting space is at a premium.
-
product
RTD Sensors
Are sensors used to measure temperature. Many RTD elements consist of a length of fine wire wrapped around a ceramic or glass core but other constructions are also used. The RTD wire is a pure material, typically platinum, nickel, or copper.
-
product
Lightning Sensors
Scientific Sales boasts a full line of lightning detectors and lightning warning alarms to protect people from unpredictable and deadly lightning strikes. Lighting monitors can detect electrical activity from up to 40 miles away and track a storm as it approaches with audible and LED alarms. Choose from a permanent lightning detector or hand-held lightning sensors for accurate and reliable lightning detection. Scientific Sales’ lightning monitors and lightning sensors are professionally rated an...show more -
product
Modbus Data Logger
Mod Bus is a popular protocol that is used by manufacturers of instruments and sensors. Site instrumentation already exists and parameters to be recorded are available on Mod bus. We have in store fro our clients Mod bus Data Logger that can read data from these instruments and record them periodically. These loggers are configured as per the site requirements.
-
product
Temperature Sensors
ams provides a range of high-accurate temperature sensor solutions that enable you to precisely monitor the temperature in your application. They are ideal for space- and power-constrained designs in consumer, industrial and personal health applications.
-
product
PXI Strain Gauge Simulator Module 4-Channel, 3k
40-265-104
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
3-Component Quartz Force Rings
260 Series
Three-component quartz force ring sensors are capable of simultaneously measuring dynamic force in three orthogonal directions (X, Y, and Z). They contain three sets of quartz plates that are stacked in a preloaded arrangement. Each set responds to the vector component of an applied force acting along its sensitive axis. 3-component ring force sensors must be statically preloaded for optimum performance. Preloading provides the sensing elements with the compressive loading required to allow the ...show more -
product
Sensors And Cables
Sensors provide the vital link between the material under test and the instrument that measures its properties. Lambient Technologies LLC has developed a variety of disposable and reusable sensors for different applications. Click on the images below to learn more.
-
product
IR Temperature Sensors for Critical Equipment Monitoring
FLIR A310
The FLIR A310 is a fixed-mounted thermal imaging camera that can be installed almost anywhere to monitor your critical equipment and other valuable assets. The camera can safeguard your plant and measure temperature differences to assess the criticality of a given situation. This allows you to see problems before they become costly failures, preventing downtime and enhancing worker safety.
-
product
PXI BRIC8 FIBO Matrix Dual 217x4 2pin brkout
40-592A-117
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
product
Sensors
Panasonic Industrial Devices Sales Company of America
Panasonic Sensor Solutions offer a wide and constantly evolving range of technologies that provide design engineers with the flexibility to easily choose and implement the Sensor technology best suited for existing and ever-emerging new applications all from a single, world class supplier. Panasonic built-in Sensors contribute to energy savings, safety and comfort. With high-functionality and high-performance, Panasonic has solutions for sensing and detecting rotational speed and angle, position...show more -
product
J-Type Thermocouples Grounded (32 deg F to 900 deg F )
745685-J01
J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.