Showing results: 226 - 240 of 343 items found.
-
TDS -
Schmid & Partner Engineering AG
Time Domain Sensor (TDS) probes are miniaturized fully isolated active optical magnetic or electric field sensors operating in the frequency range from 10MHz to 6GHz. TDS offers unparalleled sensitivity for EM measurements resolved in the time and frequency domains while maintaining all amplitude and phase information.
-
Scientech Technologies Pvt. Ltd.
Spectrum analyzers are widely used within the electronics industry for analyzing the frequency spectrum of radio frequency, RF and audio signals. RF spectrum analyzers are an essential tool for RF and other engineers, providing a view of the spectrum of signals with their amplitudes and frequencies. Spectrum analyzers can display signals up into the GHz range.
-
1250E -
Ametek Scientific Instruments
The 1250E Frequency Response Analyzer (FRA) delivers accurate measurement of gain and phase. The device under test is stimulated by a sinewave and the response analyzed at various points in the system. These responses are then correlated with the stimulus to determine the amplitude and phase relative to the generator. The ratio of the two measured signals can then be used to provide the system transfer function.
-
Analog Devices Inc.
Analog Devices digital controlled variable gain amplifiers provide discrete levels of gain control over a fixed number of control bits for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust the amplitude of a signal in real time, which is critical for a number of applications involving ultrasound, speech analysis, radar, wireless communications, and instrumentation. We also offer a portfolio of voltage controlled VGAs to provide you with continuous gain control over a wide dynamic range.
-
A400DI -
FLC Electronics Inc
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
GAO Tek Inc.
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Fairview Microwave Inc.
Fairview Microwave’s line of phase stable RF analyzer cables consists of 19 models designed to deliver optimal amplitude and phase stability with flexure. These portable test cables feature VSWR as low as 1.2:1 and a maximum operating frequency of 27 GHz, depending on the model. These rugged RF test cables feature crush resistance of 1,200 psi and an operating temperature range of -55°C to +105°C. These test cables for handheld RF analyzers are offered with 7/16, N, SMA, TNC or 3.5mm connector options.
-
Series 8000 -
Eastern-Optx
The Eastern OptX Series 8000 Radar Target Repeater is a portable, variable delay and propagation loss system designed for radar testing and alignment. The repeater may be remotely programmed in the field for dynamic operation. When connected to a user specified antenna the repeater can provide delays of up to 500 usec with a fixed delay, multiple discrete delays, or a progressive variable delay with amplitude control The Series 8000 features ultra wide bandwidth, low loss, high isolation, low noise figure, and high dynamic range.
-
60-983-002 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
60-983-003 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
60-983-001 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
ABB Ltd.
Ultrasonic Level Measurement features variable GAP technology for stable readings in the most challenging environments.The KSONIK is the only ultrasonic level transmitter that uses dynamic GAP technology in order to locate the correct echo. The KSONIK utilizes the minimum amount of GAP (Gain, Amplitude, and Power) at every possible distance within the measurement range. This simply means that we reduce the power to give you the most accurate reading with a beam angle of only 3 degrees, and then enough power to push through the most dusty environments.
-
IRD Balancing
To measure machinery or structural vibration, a transducer is needed to convert the mechanical motion into an equivalent electrical signal. Each sensor has distinct advantages in certain situations and limitations in other, so it is important to select the most suited transducer or sensor for your job. Equally, important is selecting the appropriate parameter of vibration amplitude for measurement. IRD® has a wide range of transducers and accelerometers available to help you obtain accurate, reliable data, whether your concern is vibration monitoring, analysis, or dynamic balancing.
-
784197-01 -
NI
PXIe, 42 V, 2-Channel PXI Counter/Timer Module—The Astronics PXIe‑2461 is a high-performance counter/timer module that provides easy-to-use automatic measurement functions, including phase, pulse, peak, rise/fall time, time interval and ratio measurement, all with high resolution. It features nine digits per second resolution, programmable measurement timeout, and nine different arming modes. You can set the Astronics PXIe-2461 to measure timing and amplitude characteristics in one of two voltage ranges: ±5.1 V or ±42 V.
-
CMS 356 -
OMICRON electronics
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
