Product

Nanolattice Standards for Analytical Instruments

-

VLSI Standards, Inc.

VLSI Standards, Inc.

The NanoLattice™ (NLSM) 100 nm pitch standard utilizes gratings with near perfect periodicity to calibrate magnification and scan linearity of Electron and Atomic Force Microscopes (AFM). Make the grade, with the highest quality pitch standard of its kind available.

Product

Analyse-it Standard Edition

-

Analyse-It Software, Ltd.

Analyse-It Software, Ltd.

The powerful statistical analysis and regression you'd expect from an expensive statistics package.

Product

Standard Step Tablets, Gray Scales & Density Reference Charts

-

Applied Image, Inc.

Applied Image, Inc.

Standard Step Tablets, Gray Scales & Density Reference Charts are available in a wide variety of patterns, designs and sizes to fit a multitude of today’s application needs. Our gray scales and density patches are measured on a variety of NIST traceable instrumentation, including some of the most sophisticated microdensitometers available to the industry. They are imaged on either Photo Paper (RM) or Film (TM) to function for reflective or transmissive applications.

Product

Standard - 5.00 (142.00) - 8.30 (235.00)

P3325-1

-

ECT

P3325-1 - ECT

Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 10Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 66Recommended Travel (mm): 1.68Overall Length (mil): 645Overall Length (mm): 16.38

Product

Standard Magnetizers

-

Magnetic Instrumentation Inc.

Magnetic Instrumentation Inc.

The selection of a magnetizing system begins with an analysis of the production requirements, including magnet material, magnet size, magnetizing orientation, number of poles, production speed, magnet measuring, and other operations that are necessary. After careful evaluations of these factors, and reviews of samples and/or drawings, our application engineers can recommend a system that will meet your requirements.

Product

Rugged GPS Time & Frequency Reference

VersaSync

-

Safran Federal Systems

VersaSync - Safran Federal Systems

VersaSync is a high-performance GPS master clock and network time server that delivers accurate, software-configurable time and frequency signals in harsh environments, including GPS-denied areas. Now with M-Code!

Product

Standardized Bus Interface

IP-429-II

-

Dynamic Engineering

IP-429-II - Dynamic Engineering

Connect to your Avionics with IP-429. Pick 2,4,6,or 8 ARINC 429 compatible receivers and 1, 2, 3, or 4 transmitters. Transorb protected IO. Software programmable transmit rates [100K or 12.5K]. Time Tag on received data. IndustryPack campatible with 8 or 32 Mhz. bus operation.

Product

Frequency Extender

DC100

-

DKD Instruments

DC100 - DKD Instruments

The DC100 system can be installed in the HP8568B(see H96 option below) without compromising the performance of the original instrument. The spectral purity and power accuracy of the primary band ( 100hz to 1.5Ghz) are insured from corruption by careful design of the DC100 system. Additional protection of the primary band is guaranteed as the DC100 system is automatically switched off (all power removed) when in primary band operation.

Product

High Frequency Clock Divider Board

-

Alliance Support Partners, Inc.

Alliance Support Partners, Inc.

Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.

Product

Standard Flexiforce Sensors for Force Measurement

FlexiForce

-

Tekscan, Inc.

FlexiForce - Tekscan, Inc.

FlexiForce force sensors are ultra-thin and flexible printed circuits, which can be easily integrated into force measurement applications. These sensors are available for purchase in our online store.

Product

Standard Connectors

-

C.C.P. Contact Probes Co., LTD.

C.C.P. Contact Probes Co., LTD.

The Standard Connector Series aims to offer a comprehensive selection of internationallycompatible connectors. Its smart design and simple structure makes it very cost effectiveeven at small volumes.

Product

FREQUENCY DISPLAY UNIT

TYPE NFD-1

-

National RF, Inc

TYPE NFD-1 - National RF, Inc

The National RF Type NFD-1 Frequency Display Unit was designed for use with vintage and classic communications equipment, to display the received or transmitted radio frequency. The unit incorporates an internal processor that allows the intermediate frequency (IF) to be counted out by the frequency counter. The resultant display is the actual frequency that the equipment is receiving or operating at.

Product

Standard In-door Forward Optical Receiver

ONR-8636

-

Hangzhou Huatai Optic Tech. Co., Ltd.

ONR-8636 - Hangzhou Huatai Optic Tech. Co., Ltd.

ONR-8636 with standard configuration is a type of high index and universal in-door forward optical receiver. It adopts Philip optical receiving module. End-grade adopts power-doubling module. Optical connectors and RF connector can be installed at the front panel or back panel.

Product

Current/Voltage/Frequency Converter

SCMA-VADC-710

-

Parker Hannifin Corp.

SCMA-VADC-710 - Parker Hannifin Corp.

The SCMA-VADC-710 current/voltage/frequency converter is switched between SensoControl measuring devices and hydraulic installations in order to capture the switching status of these components

Product

Standard Memory Grypper Sockets

-

Ironwood Electronics

Ironwood Electronics

Standard Memory Grypper Sockets

Product

Standard And Custom Targets

-

Santa Barbara Infrared, Inc.

Santa Barbara Infrared, Inc.

Santa Barbara Infrared manufactures a wide range of targets for visible, and infrared/FLIR electro-optical testing. These targets complement our complete line of Visible and IR test products. Our targets are designed to function with one of SBIR’s target wheels.  Utilizing a variety of manufacturing techniques, including conventional machining, photochemical etching, electro-deposition, electrical discharge machining (EDM) and laser cutting. SBIR targets are manufactured to exacting mechanical tolerances. SBIR manufactures all of the targets specified by MIL-STD-1859 and the Tri-Service Guide for thermal imager testing.