CT
1) Current Transformer 2) Computed Tomography
-
product
Digital Vibration Switch
CTD-1010
Vibration Switch CTD-1010 provides continuous automatic control and protection of industrial equipment.
-
product
Continuous Gas Analyzer
CT5100
Emerson CT5000 series, providing the most comprehensive analysis available as it can detect down to sub ppm level for a range of components, while simplifying operation and significantly reducing costs. Unlike traditional continuous gas analyzers, the CT5100 can measure up to 12 critical component gases and potential pollutants simultaneously within a single system – meeting local, state, national, and international regulatory requirements.
-
product
Current Measurements Of PWM Or Inverter, AC/DC 10～200A, Φ24mm
CTF-200DC-U24V
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 10～200A*Current measurements for PWM or inverter
-
product
Current Measurements Of PWM Or Inverter, AC/DC 1～50A, Φ16mm
CTF-50DC-U48V
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 1～50A*Current measurements for PWM or inverter
-
-
product
Converter
CTD-2160
The STD-2160 converter is a device for continuous monitoring and protection of rotary equipment. STD-2160 measures, controls and records signals from sensors continuously through 16 channels.
-
product
10 KV High-Voltage Oscilloscope Probe, CTUVus Listed
CT4432
Because an oscilloscope has limits to the input voltage it can accept, measuring higher voltages may sometimes require the use of an attenuating high-voltage probe. The CT4432, with an improved dual-resistor design, can accurately and safely step-down higher voltages to an acceptable level.
-
product
Digit Manual Range Digital Multimeter
CT8015
State of the Art ergonomic design and styling for easier handling and use. Full control manual range selection. Large 3 digit LCD display. AC/DC Voltage measurement up to 600 Volt
-
product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
product
5 Digit Preset Counter
CS2-CT
The CS2-CT provides high speed and multifunction, counting, control and communication (Modbus RTU mode) of Pulse from flow meter or encoder, proximity switch, photo switch for length control.There are 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue,and RS485 port available. They are also support N, R, C mode for totalizer control.
-
product
Classification Tree Editor
CTE
The Classification Tree Editor (CTE) is a graphical editor which by means of the Classification Tree Method is used to transform a (functional) specification into a set of test cases.
-
product
3D CT Micro Or Nano Tomography And Digital Radioscopy Compact System
EasyTom
Versatility for a wide variety of applications and analysable products. 6 motion axis. Large volume Inspection.
-
product
Current Sensor For Outdoor Use
CT-41B
MULTI MEASURING INSTRUMENTS Co., Ltd.
Equivalent to protection grade IP67
-
product
20Hz Injection Kit Monitoring System
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
product
Through Hole type AC Current Sensor
CT-6S
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
product
CLAMP ON CTS
P50
Beijing GFUVE Electronics Co.,Ltd.
The P50 is a general purpose 1000A AC current probe designed for use with DMMs, loggers and other instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw.
