Interface Adapters
Physical interface between interoperable elements.
See Also: Interfaces, Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Test Adapters
-
product
Message Based Intelligent Interface Card
IIB-3910-VXI
The IIB-3910-VXI is message based intelligent interface card for dual redundant 3910 and 3838 applications. It gives full 3910 and 3838 test, simulation and bus analysis capability on the VXI bus, providing 3910, 3838 1553A, and 1553B variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with passive Bus Monitor, and an independent Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides dual redundant prEN3715 compatible 3910 interface, with variable amplitude dual redundant 3838 interfaces. External trigger-in and trigger-out are provided, with both Primary and secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel.
-
product
Thermocouple (K-Type) And Temperature Probe Adapter
U1186A
Consists of a K-type thermocouple bead and a mini connector to dual banana plugs.
-
product
PXI Remote Control Interface Modules and Kits
Take advantage of the latest high-performance, low-cost desktop PCs for control of your PXI system.
-
product
2.92mm to ProBus Probe Adapter
L2.92A-PBUS
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PBUS adapter converts the 2.92mm interface to a ProBus interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi from high-impedance ZS active probes to the high-bandwidth WaveLink differential probing system. Full probe power and control is provided through a built-in LEMO interface.
-
product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M8KDiscrete
The M8KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M8KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports ten programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each.
-
product
MiniPCI Express to M.2 PCIe (2) Adapter (E-key)
SKU-089-11
MiniPCI Express has M.2 (E-key) connector. It allows connection M.2 modules with M.2 (E key) or (A-E key) to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits and this Adapter supports PCI express (slot 2) and USB 2.0 interfaces.
-
product
Ethernet Parallel Interface
Model 8113
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
product
Front Panel Interfacing Kit: M9018A And M9019A
Y1270A
The Y1270A Front Panel Interfacing Kit for M9018A and M9019A PXIe chassis provides a rugged interface to the front panel connectors of modules installed in the chassis. The frame is provided with a semi-transparent cover which provides additional protection for front panel cables and connectors.
-
product
25 Pin Breakout Interface
VSI-Breakout-25
The VSI-Breakout-25 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Interface ICs
Easy to use, flexible, and reliable. Allegro’s sensor interface ICs offer accurate and fast output for signal conditioning in a wide range of applications, from electric vehicle HVAC systems to transmission oil pressure. Our innovative algorithms deliver robust EMC performance and provide critical diagnosticsthat support automotive safety.
-
product
Interface and Isolation
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
product
CAMAC To NIM Power Adapter
Power adapter to use a NIM module within a CAMAC crate. Provides all 6 voltages to the NIM module. Available also in a versions with 12V DC-to-DC converter for CAMAC chassis without +/-12V.
-
product
Relay Buddy Adapter Set
190-4
*Expands the testing capability of your Relay Buddy! *3 pack of adapters allows testing of shielded relays, same relays tested by #190 Relay Buddy *Relay adapter plugs into Relay Buddy first *Shielded relay then plugs into the top of the adapter
-
-
product
Adaptive Relay, Virtex-6 FPGA - 6U VPX
Model 58624
- Modifies 68 IF signals between input and output- Up to 80 MHz IF bandwidth- Four 200 MHz 16-bit A/Ds- Four 800 MHz 16-bit D/As- 68 DDCs and 68 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Digital Serial Data Audio Interface
PIO-9216
For accurate testing of devices that use the I2S, Left Justified, Right Justified and TDM audio data formats.
-
product
ARINC 429 Test & Simulation Interface for PCI
PCI-C429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/FilteringIRIG-B time code encoder/decoder with free-wheeling modeApplication Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
4U Grille Adapter
AD-7
Used to install 19” panel width blowers, fan and grille/filter assemblies in 24” panel width enclosures.
-
product
6U Single VME Slot Intelligent Interface Card
IIB-3910-VME-2C
The IIB-3910-VME-2C is a 6U single VME slot intelligent interface card providing complete STANAG 3838 andSTANAG 3910 test, simulation and bus analysis capability, for two 3838 dual redundant and two 3910 buses, which support optical dual redundant and electrical single redundant 3910 protocols.
-
product
Interface
RAR-PXI
Available in a range of configurations to match your needs, the RAR-PXI provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected two-wire, 32-bit protocols in a PXI compatible CompactPCI form factor.
-
product
Test Adapters/ Mechanical Interchangeable Adapters
GPS Prüftechnik offers a wide range of mechanical adapters. These are mostly used for functional tests.
-
product
Digitizer Adapter Module For FlexRIO
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
product
PMC-to-4X PCI Express (PCI-e/PCIe) Adapter
6778
The Technobox, Inc. P/N 6778 is a PCI Express (PCIe/PCI-e) carrier that permits the insertion of a single PMC into a PCI-e slot (4X). The adapter orients the PMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket. Furthermore, the reverse orientation of the card permits direct access to the standard front I/O (if any) within the host chassis.
-
product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
3U cPCI Sensor Interface Unit
SIU35
NAI's SIU35 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communication, Ethernet switching, and processing. The SIU35 uses up to five NAI field-proven, 3U cPCI boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-To-Mission."
-
product
Coaxial Waveguide Adapter, Type-N (f), 8.2 to 12.4 GHz
X281A
The Keysight X281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
Multi Interface USB Adapter
SUB-20
SUB-20 is a versatile and efficient bridge device providing simple interconnect between PC (USB host) and different HW devices and systems via popular interfaces such as I2C, SPI, MDIO, RS232, RS485, SMBus, ModBus, IR and others. It is also a full "any to any" converter between all supported interfaces and I/O features. SUB-20 is a powerful I/O controller with 32 GPIO, 8 Analog Inputs, PWM Outputs, Edge DEtectors, LCD, Leds and push buttons.SUB-20 system includes SW package containing driver, API Library, GUI and Command Line based applications, C,C++,C#,VB.net, MATLAB, LabView sample code and documentation. SUB-20 can be used with PC 64/32 bit running Windows 2000/XP/Vista/Win7/Win8, MacOS, Unix/Linux and DOS.Working with SUB-20 does not require deep knowledge of low layers of the specific interface. All you need to do is to call right API function at the right place. And this is really very easy as API functions are well documented and "exampled". API set is relatively small but comprehensive.SUB-20 is equipped with status Leds, optional LCD and buttons. All this guarantee fast and comfortable development, field debugging and maintenance of applications including option of standalone operation.
-
product
FEC Accelerator Based On Intel® VRAN Dedicated Accelerator ACC100
PCIe-ACC100
ADLINK’s PCIe-ACC100 is a PCIe interface accelerator adapter developed based on Intel's vRAN Dedicated Accelerator ACC100 eASIC chip. It supports 4G and 5G codec acceleration, checksum rate matching, onboard 4G ECC memory, and hybrid automatic repeat request technology (HARQ). The PCIe form factor HHHL (half-height, half-length) can meet the needs of most application scenarios.
-
product
Pulse Adapter
CV30P650
Frothingham Electronics Corporation
The CV30 P650 test station is currently the highest voltage pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. The CV30 P650 pulse adapter can produce a maximum current of 100A at up to 600V using exponential pulses up the 10/1000 waveform. The pulser is rated at 30KW from 300V to 650V. Voltage compliance at 100A is 600V. The station can also include all of the usual FEC200 tests in the same test program.
-
product
POWER INTERFACE BOX
The POWER Box is in charge to provide power supply lines towards the UUT simulating the power distribution unit. The box has been designed to host, in any mixed configuration, two kind of plug in modules:
