PCB Test Fixtures
jigs which hold, align and engage pcb with test interconnect.
See Also: Test Fixtures, Board Test Fixtures, ATE Fixtures, Bed of Nails
-
Product
PCB Adapter, ITA, QuadraPaddle, 192 Position, To PCB-Mounted 2x68 Pin Female VHDCI Connectors
510151123
-
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Pin Female VHDCI Connectors
-
-
Product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
-
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
-
Product
Wireless Device Test
-
New wireless standards, in addition to rising wireless usage, are increasing wireless device complexity while lowering price expectations. To counter rising costs, manufacturers require test systems optimized for efficiency.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
-
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
Imperial Test Executive
ITE
-
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
-
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
PCB Adapter, Receiver, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510104128
-
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
Product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
-
Stopper kit includedYAVCANCON2 for fixture identification not included
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2 x 68-Pin FML VHDCI
510150126-1
-
Single PCB adapter p/n 510150126 ships with 2 x 68-pin VHDCI male double-ended 2m cables, packaged separately. Available PXI card solutions for NI PXI-2535 and PXIe-7868.
-
Product
Scienlab Combined Battery Test Solution
SL1133A
-
Solution for testing battery cells with an output power up to ±3 kW and a voltage range up to 6 V.
-
Product
Fixture Self-Test Controller and Calibration Check
AQ818
-
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
Product
EBIRST 78-pin D-type Verification Fixture
93-006-101
-
The 93-006-101 78-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2 PCB-Mounted 12X Male InfiniBand Connectors (LVDS)
510150210
-
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2 PCB-Mounted 12X Male InfiniBand Connectors (LVDS)
-
Product
PCB Adapter, ITA, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510108140
-
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
Product
PCB Adapter, Receiver, TriPaddle, 96 Position, To PCB-Mounted 1x96 Male DIN 41612 Connector
510104139
-
The 96 Pin Signal receiver module is made from Ryton R-7, withstanding temperatures up to 220°C. Nomenclature is molded on the module.
-
Product
Parallel Electrode SMD Test Fixture
16192A
-
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
Product
Flight Control System Test Platform
-
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
Component Test Systems
-
These products include test peripherals used with test systems, such as interfaces that connect semiconductor devices with test systems, and handlers that transport semiconductors to the test system. System-level test equipment and software are also included in this category.
-
Product
BSD (Test Diagnostics)
-
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
-
Product
PCI Express 4.0 Test Platform
-
The PCI Express 4.0 Test Platform provides a convenient means for testing PCIe 4.0 add-in cards with an internal interposer and power supplies. The Summit Z416 Test Platform provides the platform for the Summit Z416 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen4, Gen3, Gen2 or Gen1 hosts and devices. It supports SMBus and other sideband signals.
-
Product
PCB Adapter, Receiver, SIM, VTAC, 96 Pos, 14 Slot, to (1) 12x InfiniBand
510170108
-
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single 12x InfiniBand connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules.
-
Product
Asynchronous System Level Test Platform
Titan
-
The Titan System Level Test (SLT) platform delivers maximum flexibility, scalability and density in semiconductor test environments that require the highest levels of system performance testing. Titan is Teradyne’s solution for high-volume mobile application processor SLT requirements.
-
Product
EBIRST 200-pin LFH To 96-pin SCSI Adapter Cable
93-002-226
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
JTAG Functional Test
JFT
-
JFT comprises a series of software modules that support boundary-scan test and programming activities under Python, National Instruments LabVIEW and Microsoft .NET framework. Using JFT users can create JTAG/boundary-scan test application scripts, VIs or programs for PCB assemblies and systems that control individual driver/sensor pins, groups of pins declared as variables or register bits. These applications are typically used to test logic devices or mixed signal clusters and can also be transformed into re-usable test 'modules'. Pairing JFT with JTAG CoreCommander emulative test modules gives an effective, low-cost system for performing tests through embedded device peripherals (ADCs, Memory Controllers etc..)
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x96 SCSI Connectors
510150120
-
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x96 SCSI Connectors
-
Product
Connector PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x96 Male SCSI
510150128
-
Connector PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x96 Male SCSI
-
Product
PXI Digital Test Instrument
PXIe-6943
-
Conduct pattern-based digital tests incorporating the latest parallel, digital, serial, and bus protocols with the PXIe-6943 digital test instrument.This instrument is TPS-compatible with the legacy VXI digital test instrument from Astronics as well as other instrument vendors.
-
Product
Manual Test System for ICT & ISP with Integrated ABex and up to 426 Test Points
LEON Fixture
-
The LEONFixture is the ideal ICT and ISP solution for small and cost sensitive applications. This manually operated test system combines optimal ergonomics with high performance, durability and precision, ensuring your investment over the long term. The LEONFixture features a test system integrated in a manual base fixture. The system is designed to be used with an Ingun ATS MA13 insert which could be customized by a lot of fixture houses all over the world.As part of the LEON Family, LEONFixture is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
