Humidity Chambers
Controlled analysis of a product exposed to humid conditions.
See Also: Environmental Chambers, Chambers, Temperature Chambers
-
Product
UV Weather Resistance Test Chamber
-
This series is applicable for the sunlight resistant test of nonmetallic materials and aging test of artificial light source.
-
Product
Temperature and Humidity Duct Probe
T3113D
-
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
Thermal Shock Test Chamber (3 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Divided into a high-temperature zone, low-temperature zone, and test zone. The test product is placed in the test zone, and the temperature from the high-temperature zone or low-temperature zone is applied to the test zone for thermal shock. The test product remains static during the test.- Equiped with a touch-screen control interface for easy operation.- Temperature is transferred to the test zone using a wind route switching method to perform thermal shock testing.- The maximum duration of high-temperature or low-temperature shock can reach 999 hours, and the maximum cycle period can reach 9999 cycles.- The system can operate in automatic cycle mode or manually select specific shocks. It can be set to perform two-zone or three-zone shocks, as well as cold-to-hot or hot-to-cold transitions.- The cooling system utilizes a dual refrigeration system, providing fast cooling. Water cooling is employed as the cooling method.- Testing can be performed at room temperature.
-
Product
Dual Channel Temperature/Relative Humidity
TGU-4500
-
Temperature and relative humidity recorder 32,000 readings capacity High accuracy and reading resolution Fast data offload Splashproof case Low battery monitor User-replaceable battery USB or serial download cables User-programmable alarms
-
Product
Modular Walkin Chamber
-
CME’s Modular Walk-In chamber offers unmatchable flexibility in installation. The panelised construction is engineered to perform at demanding testing conditions offering highest reliability and performance. Besides modular construction, we also offer Walk-In chamber made from welded rigid panels.
-
Product
IPX7 Water Ingress Protection Immersion Test Chamber
CX-IPX7
-
Shenzhen Chuangxin Instruments Co., Ltd.
IPX7 Water Ingress Protection Immersion Test ChamberThe main function of the immersion test equipment is for the electronic and electrical products, lamps, electrical cabinets, electrical components, automobiles, motorcycles and their parts and other products in the simulated rain conditions, the physical and other related properties of the test.
-
Product
Climate Control Test Chamber
-
ACMAS's Climate Test Chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. ACMAS Thermal Cyclic Chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperature ramp control. This chamber is also known as Climatic Test Chamber and Climate Controlled Test Chamber.
-
Product
Transmitters for Pressure, Humidity, Temperature, CO2
-
Wuntronic Transmitters for Pressure, Humidity, Temperature, CO2
-
Product
Rack-Mountable CATR Chamber for 5G NR mmWave Signals
ATS800R
-
The R&S®ATS800R CATR based 5G NR mmWave test chamber provides a very compact over the air (OTA) testing environment for testing 5G FR2 antennas, modules and devices in R&D. The R&S®ATS800R has a very small footprint and wide frequency range, and offers maximum functionality and test coverage in a small space. The flexible setup options and range of extensions make the R&S®ATS800R a solid and future-proof environment for your FR2 testing needs.
-
Product
3-Axis AGREE Chamber Vibration Test Chamber Elevator Mechanism
-
Guangdong Test EQ Equipment co., Ltd.
Widely used in aviation, aerospace, shipbuilding, defense, electrical engineering, electronics, automotive, motorcycle, telecommunications, and scientific research industries. Designed to assess the reliability of electrical/electronic products, instruments, and equipment during transportation, storage, and operation. This integrated system combines a temperature/humidity test chamber with vibration platforms to independently conduct temperature, humidity, vibration, and combined environmental tests.
-
Product
2-Zone and 3-Zone Vertical Thermal Shock Chambers
FS
-
Originally developed for testing microelectronic devices for use in military and aerospace electronic systems, Bemco Vertical Thermal Shock Chambers are widely used for screening and quality evaluation of smaller electronic parts.
-
Product
Altitude Test Chamber
-
Environmental adaptability and reliability test for the instruments and meters, electrical products, materials, spare parts, equipments, etc at a low pressure, high temperature, low temperature, under the effect of single factor or multiple factors at the same time. Test for electric performance parameters of the specimen. Mainly used in aviation, aerospace, information, electronics and other industries.
-
Product
Environmental Stress Screening (ESS) Chamber
ESS
-
Developed to help electronics manufacturers detect product defects and production flaws, Environmental Stress Screening (ESS) forces infancy product failures that would otherwise occur after final assembly and product delivery. ESS’s goal is to improve profitability by eliminating defective products. ESS Systems can meet individual performance needs, product loading, and throughput requirements. Thermotron has the experience to provide the best solution for ESS testing at your company.
-
Product
TSA Thermal Shock Chambers
-
Traditional three-zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air is pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
Product
Temperature/Relative Humidity Logger - Grey Case
TV-4501
-
Temperature and relative humidity recorder LCD display of current readings 30,000 readings capacity High accuracy and reading resolution Fast data offload Splashproof case Low battery monitor and battery low indicator Programmable alarms Optional audible alarm box USB and serial download cables
-
Product
RF Diagnostic Chamber
DST200
-
The R&S®DST200 RF diagnostic chamber is the ideal environment for RF analysis during development. It supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used at all times during the product design and optimization phase. The R&S®DST200 effectively assists in achieving high first-time pass rates during final type approval, which saves time and money.
-
Product
Stress screening test chambers for temperature and climate
TS and CS series
-
Our based on the modular concept of the standard range of temperature and climatic stress screening test chambers allow you through increased compressor and large fan performance very high temperature change of up to 30 K / min with conventional refrigeration, or to 70 K / min with liquid nitrogen. These devices allow you to very quickly determine the load limits of your test object in fast motion.
-
Product
Benchtop Temperature Chamber | Environmental Test Chamber
-
The first true Hybrid Temperature Chamber/Platform combination called the Hybrid Benchtop Chamber. The floor of the chamber is a completely functioning Hot/Cold Plate, independent or simultaneous with the chamber. Our models come in different sizes: Micro, Small, and Medium thermal Chambers.
-
Product
Temperature Chambers Environmental Test Chambers
-
Proven Traditional Designs, evolved with New Generation FeaturesCyro Chambers come with 1 year Guarantee
-
Product
Altitude Test Chamber
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Morningtest altitude test chamber combines temperature and altitude environments with optional humidity for simultaneous environmental testing. An altitude chamber allows users to control the environmental test chamber temperature while subjecting the product under test to various levels of altitude up to 150,000 feet.
-
Product
Rain Spray Test Environmental Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s rain spray test environmental chamber is also known as rain spray test chamber, it is used to test the water resistance for electronic and electrical products, such as solar lights, garden lights, buried lights, tunnel lights, car lights, fountain lights, the display…etc. It can also provide references for product design and quality control.
-
Product
Refrigeration Training Chamber
-
The most effective way to help a student learn about refrigeration is through hands-on experience. Skill retention and efficiency improve when they are practiced and applied in a setting that simulates real work experience. In cooperation with a local vocational program, Thermotron developed the S4-T Refrigeration Chamber.
-
Product
Thermal Shock Test Chamber (Three Zone)
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
Product
Wireless Airflow Temperature Humidity Adapter
DTHA2
-
UEi Test & Measurement Instruments
Airflow Temperature Humidity Adapter with Free App
-
Product
Temperature Humidity Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Battery high low temperature test chamber is designed to test all types of batteries, including lithium-ion batteries. The battery test chamber has many safety functions built into the test chamber, which can handle battery tests and prevent safety accidents. Charge/discharge cycle testing, which determines the number of times a battery can be used by evaluating it until it deteriorates after repeated cycles of charging and discharging. In the laboratories involved in battery testing, tests based on charge and discharge cycles are a key activity. The instruments used for this type of test usually perform harsh and lengthy test protocols on the battery and can usually be connected to various instruments.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
Benchtop Environmental Test Chambers
-
Benchtop Test Chambers provide superior performance over a wide range of applications. Ideal for testing smaller products such as computer components, these chambers combine superior performance with compact design that is perfect for research and development or personal point-of-use testing.
-
Product
Thermally Protected Ballast Heating Test Chamber
TPB-UL935
-
Working room dimension: 610×610×610mm• Temperature range: RT+10℃～+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)
-
Product
Box Rain Test Chamber
-
Comprehensive box rain test chamber (with swing pipe and right angle tube) is used to test the electric and electronic devices by simulating natural rainfall with spraying water from the water nozzles (holes) on swing pipe or straight tube. To estimate and recognize if the shell or sealing elements of these device could ensure a good condition of working during and after the test. The products are widely used in the industries of light, electrical, electronics, automobile, motorcycle, household electric appliances, electromechanical equipment, instruments and meters, and other industries.
