Humidity Chambers
Controlled analysis of a product exposed to humid conditions.
See Also: Environmental Chambers, Chambers, Temperature Chambers
-
product
Cytogenetic Drying Chamber
CDS-5
Developed in cooperation with Mayo Clinic, Thermotron's Cytogenetic Drying Chamberthe CDS-5was specifically designed for conducting cytogenetic slide drying tests during harvest of in situ and non-in situ grown cultures. The CDS-5 provides the optimum controlled temperature and humidity environment required to achieve ideal chromosome spreading results. As evidenced in research conducted by the Cytogenetics Laboratory at Mayo Clinic, the CDS-5 facilitates reliable and repeatable chromosome spreading. The use of an environmentally controlled drying chamber is a practical and cost effective way of achieving ideal chromosome spreading in a routine and highly consistent manner. Favorable chromosome spreading results can be obtained for both in situ and non-in situ cultures including PHA stimulated lymphocytes, bone marrow, amniocytes, and fibroblast.
-
product
UV Test Chamber
Wewon Environmental Chambers Co, Ltd.
* UV test chamber simulates damaging effects of long term outdoor exposure of materials and coatings by exposing test samples to varying conditions of the most aggressive components of weathering – ultraviolet radiation, moisture and heat. * UV test chamber use fluorescent lamps to provide a radiation spectrum centered in the ultraviolet wavelengths. Moisture is provided by forced condensation, and temperature is controlled by heaters. Based on your testing sample’s size, We has two options uv test chambers for choice.
-
product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-F
Breakout board for the Sensirion SHT31-DIS-F with a built-in permeable membrane filter. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
product
Hand-held meter for humidity / temperature
OMNIPORT 30OMNIPORT 30
The state of the art hand-held for precise measurement of various physical quantities, such as, humidity, temperature, dew point, air velocity, volumetric flow, air pressure. The numerous probes all incorporate high quality sensors developed by E+E and offer a total of 22 measurands.
-
product
Altitude Test Chamber
Environmental adaptability and reliability test for the instruments and meters, electrical products, materials, spare parts, equipments, etc at a low pressure, high temperature, low temperature, under the effect of single factor or multiple factors at the same time. Test for electric performance parameters of the specimen. Mainly used in aviation, aerospace, information, electronics and other industries.
-
product
Endpoint / Chamber Health Monitor based on Optical Emission Spectroscopy and MWL Interferometry
EV 2.0 Series
To address new requirements in Semiconductor, lighting devices, automotive components, flat panels, MEMS sensors, memory chips, and logic electronics processed in the industry using dry etch, cleaning and (PE)CVD, HORIBA has introduced a unique generation of sensor dedicated to Advanced Endpoint Control, Fault Detection and Chamber Health Monitoring.
-
product
Relative Humidity Outdoor, Indoor Probe
T1110
Only relative humidity output 4-20mA.Also available with direct temperature RTD Pt1000 sensor output.Other sensors on request.
-
product
Custom Environmental Test Chambers
Does your environmental testing conditions have special requirements, or are you unsure of the right product for you? Tenney and Lunaire Environmental offer custom environmental test chambers - including custom climate chambers and custom vacuum chambers. The experienced Tenney and Lunaire team can provide customizations to their climatic chamber models based on client needs. Contact the sales team today to discuss you specific testing requirements.
-
product
Altitude Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
The altitude test chambers of Sanwood Technology is designed to allow users to perform temperature, humidity, and altitude condition tests in a combined test chamber, and create multiple conditions to meet multiple test requirements at the same time.
-
product
Car in Cold Temperature Shock Chamber
Dongguan City Simplewell Technology Co. Ltd.
Car in Cold Temperature Shock Chamber by Simplewell
-
product
Test Chamber
Immunity
Laplace can supply high performance mobile, bespoke and customised mobile RF and Antenna chambers which have been developed to meet all types of customers’ requirements. These mobile RF and Antenna chambers are very high performance and offer +100db of shielding attenuation @ 40GHz and can be fitted with best-in-class absorbers rated up to 110 GHz.
-
product
Humidity and Temperature Duct Transmitter
T3113Ex
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Ozone Test Chamber
EKT-2001OZ-HPSSX
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
product
IP X3, X4 - Rain Test Chamber
The rain water or moisture penetrating through a leak in the case, can often reach into the circuit board and lead to failure of the equipment. This problem is frequently encountered with external equipments and devices during storage, usage or transportation in a rainy weather. Therefore, the automotive industries and various research and developmental units often use Rain Test Chambers to test the quality and performance of the product in such extreme environments.
-
product
Climatic Test Chamber
Before anything reaches out for market distribution, you would need to determine its exact quality and performance to that follows to the point with readings. Thermal and environment testing are some of the most positive aspects to get your materials tested for their underlying performance capacity and reliability in quality.
-
product
Altitude & Space Simulation Test Chambers
Weiss Technik’s vast experience with altitude, thermal vacuum, low temperature and space simulation test chambers can provide you with the right solution. We offer both pre-engineered and custom altitude chambers for ultra-low cooling, extended mbar, and extended temperature ranges that will meet your testing exact requirement.
-
product
Relative Humidity Kelvin Probe
RHC
The Relative Humidity Kelvin Probe (RHC) systems are the ideal solution for monitoring samples in a controlled atmosphere for contact potential difference (CPD)/work function (Φ) measurements.
-
product
Archival Storage Chambers
AR Series
The Darwin Chambers AR series is designed specifically for the needs of archival preservation. This series is capable of providing long-term controlled storage of photographs, film, rare books, papers, and paintings. Utilizing a simple. precisely controlled refrigeration system and advanced desiccant-based dehumidification, temperatures are maintained to within ±0.2ºC (at the sensor) and relative humidity to within ±1% (at the sensor).
-
product
Temperature Humidity Vibration Combined Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Temperature Humidity Vibration Combined Test Chamber meets national standards and meets specific testing requirements. It is widely used in electrical and electronic products, automotive parts, materials, etc.
-
product
Stability Testing Chamber - Single Door Model
Q40
Canden stability testing chamber is capable of maintaining stable temperature set points of 25°c , 30°c & 40°c corresponding relative humidity set points of 60%RH(@25°c), 65%RH(@30°c) and 75% RH(@40°c) with exceptional precision. The chamber has a wide operating temperature range of 18°c t to 40°c maintaining a stable temperature across the entire range.
-
product
Temperature and Humidity Transmitter
DST1000
Design for airflow velocity and heat transfer rate Applied to HVAC and clean room High-accuracy,wide-measuring range Wide view angle LCD for sharp display Analog or digital output with current ,voltage and RS485 On line calibration-availability
-
product
Walk In Chambers
Our climate cells are built in the unit assembly system. This allows adaptation to the specific conditions of the effective test room size and shape. The test cells consists of the following main construction groups:
-
product
Salt Spray Test Environmental Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Salt spray chamber is used to test materials likes paints, electroplating, non-organic, pastry film, anode treatment and rust prevention oil’s corrosion resistance performance. Besides, anti-corrosion treatment of various materials to make their products resistant to corrosion.
-
product
Reverberation Chambers
Reverberant Test Chambers for sound power level determination and building acoustics measurements
-
product
2 Zone Thermal Shock Test Chamber
2-Zone Thermal Shock Testing Equipment with programmable electronics.
-
product
Environmental Stress Screening (ESS) Chamber
Guangdong Test EQ Equipment co., Ltd.
- Integral structure, the inner wall special process rolling molding, the whole using TIG seamless welding, beautiful appearance; Door lock device adopts lever power opening mechanism.- The use of Chinese+English color LCD touch man-machine interface + high-performance programmable controller (PLC), with TESTEQ test box special software, with automatic, intelligent, human control and other characteristics.- Control mode: constant operation mode, program operation mode.- Patented "Cold and heat balance technology”, low temperature constant temperature season can be more than 30%.- Refrigeration compressor and key accessories are selected international and domestic well-known brands, long-term and reliable operation; Environmentally friendly refrigerant, in line with the requirements of international environmental protection conventions.- Configure RJ45 communication interface, remote control system (open data transmission protocol support Modbus/OPC).- Surface electrostatic powder spraying; Box color "TESTEQ White ", controller panel color "TESTEQ Blue ".- TESTEQ patent cold well adsorption anti-condensation function (optional).
-
product
HMV Horizontal Flame Chamber - Motor Vehicles
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
product
Temperature Chamber
MTC-20
Improve your temperature dependent testing with the Compact Bench Top Temperature Chamber, seamlessly integrated with a Maccor Automated Test System. Its compact design allows for easy placement on any benchtop. For increased capacity, you can install up to 4 chambers into a standard 19” industrial rack cabinet.
-
product
Anechoic Chamber
EMC-3
A 3 meter test range ensuring fully compliant Emission and Immunity testing. Ferrite and hybrid pyramidal absorbers are combined in a unique pattern within a SmartShield high performance chamber. Operating at a 3m test distance, this chamber is compliant to CISPR-16 with a measurement zone diameter of 1-2 meters.
-
product
Agree Chamber
King Design Industrial Co., Ltd.
*Applying to Aircraft, Military , Vehicle and all kinds of Electronics products.*The reliability testing will approach the real circumstances nearly.*Simulating the true temperature, humidity and vibration testing in the nature.*Temperature, humidity and vibration testing could be done in the meantime, or separately. *Colorful LCD display panel and micro computer control. *All data be recorded in the floppy disk is easy for analyzing and curve plotting by PC.*Controller of vibration system: Linear, Logarithm, Octave sweep*VTH testing simulate the actual operating environments*Random, Sine, Linear vibration testing
