Interoperability Test
assures functionality between two or more systems.
See Also: Interoperability Testing, Functional Test, Standards
-
Product
Package Test
-
WinWay’s commitment to technology, quality and service ensures our interface solutions go above and beyond to exceed your expectations. Our products and services have a proven track record of delivering customer success in semiconductor testing. The Company offers comprehensive test interface solutions ranging from wafer-level test, package-level test to thermal management.
-
Product
Testing Software
-
SMC supplies as standard several types of software adapted to each set, for automatic testing, unit operation and reports or results acquisition, which allows the full functionality of the equipment; the following programs are included with the corresponding equipment:
-
Product
Test Fixtures
-
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Product
6TL22 Off-Line Testing Platform
H71002200
Test Platform
Learn about our Build to print service for Test Platforms. The 6TL22 Platform is a perfect base for the conception of a real modular Automatic Test Equipment for low to mid manufacturing volumes.A system designed around the 6TL22 is simple, easy to maintain and cost effective. The rack is prepared for the direct integration of the three platform based receivers from Virginia Panel, the S6, G12 and G12X.
-
Product
Test Sockets
-
Yamaichi Electronics Co., Ltd.
A test socket is the ideal point to test your home’s internal phone wiring for faults. You can also use it to identify any potential faults with the phone line outside. Your test socket is located in your master socket. It is the point between the internal phone wiring in your house and the phone line outside. That means by plugging into your test socket you can bypass all the internal wiring and test your device directly on the phone line.
-
-
Product
Test System
-
Maynuo Electronic Co.,Ltd a professional R & D and production of programmable DC electronic loads, programmable DC power supply, high power load, power supply, AC power supply, power supply, such as testing high-performance mobile phone test equipment and facilities, as well as electrical, electronic, aerospace, military, chemical, automotive, battery charger, battery, solar cell production lines and other industries to provide automated testing program. The company has many years experience in a number of outstanding technical R & D, product innovation by the majority of users. We are committed to provide users with more accurate and more stable more easily accessible to the higher cost of test instruments, to create the industry in testing the influence of an international brand of excellence.
-
Product
Test Patterns
DisplayMate Multimedia Edition
-
DisplayMate Technologies Corporation
DisplayMate Multimedia Edition is the most advanced and powerful version of DisplayMate ever, with lots of proprietary and highly innovative suites of test patterns for setting up, tuning-up, calibrating, testing, evaluating, diagnosing, and analyzing CRTs, analog and digital LCD, Plasma, DLP, LCoS, and SXRD monitors and projectors, microdisplays, video boards, color printers, TVs and HDTVs, NTSC/PAL Television encoders and decoders, and more.
-
-
Product
Test System
Series 303
-
The 303-Relay Test System tests the integrity of electromechanical relays and switches. The system can perform an array of tests and control output binning in a fraction of the time of any other tester on the market. Ease of use and overall system flexibility make the 303 ideal for applications in development, incoming inspection, and production line testing.
-
Product
HALT/HASS Testing
HALT HASS Chamber
-
AST applies stresses (such as temperature and vibration) to products well beyond its normal use environment. This type of testing is done to determine product operating and destruct limits. These stresses are applied as the product is functionally tested and continuously monitored for failures.Highly Accelerated Stress Testing (HALT) and Highly Accelerated Stress Screening (HASS) are two types of accelerated stress testing. These types of tests are commonly used to eliminate design problems, helping to develop a robust, mature product prior to market introduction. It can also be used to screen out infant mortality issues prior to shipment.
-
Product
Automation Testing
-
At Updoer Technology, we strive to provide a streamlined experience. We follow the test-driven approach to maintain your app's quality, and you get bug-free software and quality at its best! As a valued client, we want to ensure that you're getting what you paid for; Your satisfaction comes first at Updoer Technology because we value relationships over everything else.
-
Product
Supercapacitor Test
-
The CT3001A/C battery test systems are upgraded from CT2001A/C with higher precision and data logging rate. The tester can be used to run precision tests for coin cells, pouch cells, prismatic cells, and especially supercapacitors (ultra-capacitors). Each tester has 8 independent channel which can be programmed to run constant current charge/discharge, constant voltage charge, constant power discharge, constant resistant discharge, and direct current internal resistance (DCIR) tests.
-
Product
Vibration Testing
-
DATASYST Engineering & Testing Services, Inc.
Small, medium and large electro-dynamic vibration systemsServo-hydraulic vibration systemsCombined environment system (Temp-RH/Vibration)
-
Product
Corrosion Test
-
The purpose of this test is to determine the resistance of materials and protective coatings to corrosive atmospheres when a more corrosive environment than the salt fog/spray test is required. The test is used when material is stored or operated in areas, for example, where acidic atmospheres exist, such as in industrial areas or near the exhausts of any fuel-burning device. Gases such as sulfur dioxide are used to replicate the exhausts of fuel burning devices.
-
Product
Drive Controller Function Test – Universal Functional Test System for Industrial Electronics
Functional Test
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
Product
Board Test
-
The Horizontal/Vertical Signal Integrity Manual Work Station allows for multiple size circuit board configurations.
-
Product
Test Adapter
FECVF1600
-
Frothingham Electronics Corporation
The VF1600 Test Station is a high current forward pulser designed to be used in conjunction with our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of much higher forward current. The VF1600 station can produce a maximum current of 1600A at up to 5V using an 8.3 mS half sine waveform at the built in test station, and THETA and DVF tests at up to 500A at 10mS pulse width. It is derated for wider pulses. For rectangular VF pulses at 300us or 1ms, it can produce up to 2000A. The station can also test all of the usual FEC200 tests in the same test program.
-
Product
VLSI Test System
3380P
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Chemical Testing
-
Our modern and comprehensive Chemical Laboratory has been certified and registered in accordance with the Environmental Laboratory Accreditation Program (ELAP) and by the State of California Department of Health Services.
-
Product
Test Switches
RTS
-
STATES Type RTS Test Switches are designed to simplify and speed testing and check-out of relay, control and instrumentation systems. They eliminate the need to change connections and prevent open-circuiting CTs during tests.
-
Product
Torque Testing
-
Torque testers measure properties such as torsional strength and stiffness and are used in quality control of various fields including medical devices, metals, and aerospace
-
Product
EMC/EMI Testing
-
NCEE Labs has state of the art test equipment and experienced iNARTE EMC/EMI and qualified staff to provide Electromagnetic Compatibility (EMC) and Electromagnetic Interference (EMI) testing. The lab maintains accreditation to the latest FCC, CE and other international EMC/EMI standards.
-
Product
Acoustic Testing
-
Our acoustic testing experience includes acoustic qualification and evaluating sound pressure levels. We utilize microphones, pressure trans-ducers, and an acoustic intensity meter to record acoustic measurements.
-
Product
Microwave Testing
500B
-
The Model 500B Picoprobe sets new® standards in microwave probing performance. Benefiting from coaxial techniques, which have inherent low loss and low dispersion characteristics, the Model 500B Picoprobe achieves an insertion loss of less than 4.0 db and a return loss of greater than 15 db over its frequency range (see accompanying data).
-
Product
Material Testing & Physical Testing
-
Meeting the specifications put out by testing equipment manufacturers is critical when conducting quality control testing. We carry a wide variety of materials testing and physical testing products that are ideal for quality control testing along with research applications, letting you evaluate and test materials such as plastics, coatings, and chemicals. Physical properties testing products range from force and torque instruments, to hardness and thickness gauges, to viscometers and spectrometers.
-
Product
Test Solution
Eye-BERT MicroX
-
The Eye-BERT MicroX is a compact, easy to use test solution offering high performance bit error rate testing at a fraction of the cost of competing solutions. The unit is offered in two speed grades including the X10 which operates up to 14.5Gbps, and the X30 which extends the data rate to 29Gbps. Its broad data rate capabilities and long test patterns make this unit suitable for testing nearly all optical SFP, SFP+, and SFP28 transceivers in production with just one unit. The real-time eye opening monitor and eye scanning capability can aid in troubleshooting by providing the operator with additional link quality information. Other features include Autonomous pattern detection, SFP diagnostic tools, and wavelength tuning (per transceiver capability). With a click of a button the Eye-BERT MicroX will automatically test an SFP module based on its advertised capabilities and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
EMC Testing
-
Does your product send or receive electromagnetic data? This can be analyzed using various tests. We investigate the interference immunity and emitted interference of simple electrical devices and complex machinery. Our EMC measurements and tests conducted in accordance with standards recognize all activity in the electromagnetic field and ascertain how immune to interference a piece of equipment is. We will also offer guidance on optimizing the product in terms of its EMC properties during the development phase.
-
Product
Load Testing
OctoPerf
-
Use auto-correlations rules and frameworks as well as test validation to quickly create virtual users.
-
Product
Microwave Testing
220
-
The PICOPROBE® MODEL 220, a high performance microwave probe which incorporates a WR-5 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
