Fibre Channel over Ethernet
technology handles Fibre Channel protocol through 10 or > Gigabit Ethernet.
-
product
PXI 4 Banks of 20 Channel 2 Pole MUX
40-615-022-4/20/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
PXI Single 2 Channel (M Mode) ST 50 Cons
40-855-512-M50
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
product
Infiniium S-Series High-Definition Oscilloscope: 8 GHz, 4 Analog Plus 16 Digital Channels
MSOS804A
8 GHz bandwidth4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 6.4 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
product
Oscilloscope, 0+2 Channel, 100 MHz, 500 MSPS, 6 kpts, 3.5 ns
72-8474
72-8474 Compact handheld unit provides outstanding Two Channel colour DSO Oscilloscope performance plus added functions of a full featured digital multimeter.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 1 Channel (Single Ended) or 1 Channel (Differential)
M2P.5960-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PXI Quad 2 Channel Optic Mux LC
40-855-442
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Ethernet MACsec PHY
Macom Technology Solutions Holdings Inc.
IEEE 802.1AE Media Access Control Security (MACsec) is an industry standard security technology that provides secure communication for Ethernet traffic. MACOM’s wire-speed Ethernet MACsec PHY products offer highly scalable and cost-effective encryption solutions to address the data security issues in wireless, carrier, data center and cloud networks. Combining MACOM’s strength in high speed, high performance mixed-signal I/O and industry leading CMOS silicon technology, MACOM’s MACsec PHY products provide line-rate encryption and authentication at a very low power-footprint that enables encryption at wire-speed on every port. They are ideal for adoption on switch/router line cards, data center interconnect (DCI) transponder and wireless xHaul aggregation systems to provide security function in addition to the connectivity to optical and copper modules.
-
product
PXI 4 Banks of 20 Channel 1 Pole MUX
40-615-021-4/20/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
4 Discrete/Switch I/O Channels (±100 V, 3 A/Ch.)
DT3
The DT3 module (the enhanced version) feature 4 independent, high current, isolated, programmable channels that can be used for input voltage measurements (±100 V), or as a bi-directional current switch (up to 3 A per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
product
Infiniium S-Series High-Definition Oscilloscope: 6 GHz, 4 Analog Plus 16 Digital Channels
MSOS604A
6 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 6.8 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
42-204-002
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
product
14 Bit Digitizer For PCIe With 8 Channels 25 MS/s Up To 8 GS Memory
Octopus-14 Express / CompuScope Express 8382
The GaGe Octopus Express 83XX CompuScope PCIe digitizer board features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11-bits with 10 MHz input.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - United Kingdom 240VAC
781630-06
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
16 Channels, 200MHz, 1 M Samples/Channel Buffer USB Logic Analyzer
La-Logic-16
The La-Logic-16 is a sophisticated PC-based logic analyzer. It captures at a maximum of 200Mhz on its 16 channels simultaneously into it?s deep 1M samples/channel buffer.It can also operate as a 16-channel pattern generator.It connects to the PC via the USB-port and does not require any external power. The package is complete with all accessories included to start debugging immediately.
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 250 MS/s on 4 Channels Digitizer, 625 GS/s AWG on 4 Channels
DN2.822-04
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
2 To 18 GHz 6 Channel Downconverter
Teledyne RF & Micrrowave's Six Channel 2 - 18 GHz (RF and LO) downconverter operates with an IF of ~960 MHz, providing 25 dB of RF-IF gain, and bandwidth of ~500 MHz. This downconverter operates on a single LO at -6 dBm which is amplified, split, then again amplified to each of the 6 channels. Integrated into each channel is a range extension switch, controlled by a TTL input and adding 20 dB attenuation. Noise figure is ~ 13.5 dB and output IP3 is ~+25 dBm. The downconverter is 2- sided, hermetically sealed and designed for rugged applications.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 2 Channels
M2P.5911-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels
-
product
8 CANBus Channels, CAN 2.0 A/B Protocol or J1939 Protocol
CB3
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
product
20-port Ethernet Switch
VPX3-652
Curtiss-Wright Defense Solutions
The VPX3-652 is a fully featured Layer-2 managed Ethernet switch designed to support advanced network architectures for the defense industry.
-
product
WaveRunner 9254M-MS (2.5 GHz Bandwidth, 4+16 Input Channels, 40 GS/s on 2 Ch Sample Rate
WaveRunner 9254M-MS
2.5 GHz, 40 GS/s, 4ch, 64 Mpts/Ch Mixed Signal Oscilloscope with 15.4" Capacitive Display.
-
product
Oscilloscope 40 GHz, 2 Channels, 1mm Inputs
UXR0402BP
XR0402BP Infiniium UXR-Series is the 40 GHz, 2 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
product
OpenVPX Ethernet I/O rear transition module.
EnsembleSeries™ RTM30P
*Companion Rear Transition Module for 3U OpenVPX Xeon® D-series process payloads (LDS3506)*Field Replacement Unit capability
-
product
Single Channel Potentiostats
Potentiostats control a voltage and measure a resulting current. The Control Amplifier outputs power to the counter electrode (also called auxiliary electrode). A feedback loop is established to control the cell potential between the reference and working electrode. This voltage is measured by the input electrometer, that has a high impedance. This current is then measured between the working and counter electrodes while this potential is maintained at the working electrode and reference electrode.
-
product
PXI RTD Simulator Module, 4 Channel, PT500
40-263-502
The 40-263-502 is a 4-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
product
Oscilloscope - 1-6 GHz, 4 Analog Channels
DSOX6004A
1 GHz - 6 GHz4 analog channels Easily view and isolate signals on the 12.1-in capacitive multi-touch screen with Zone triggering and 450,000 wfms/s update rate Make more precise measurements with 115 uVrms noise floor at 1 mV/div (1 GHz)Get performance measurements anywhere with the portable 6-in deep size Quickly see analysis details with standard histogram and color grade View signal integrity with jitter and eye diagram analysis options
-
product
16 Channel Multievent Peak Sensing ADC
V785N
The Model V785N is a 1-unit wide VME 6U module housing 16 Peak Sensing Analog-to-Digital Conversion channels. Each channel is able to detect and convert the peak value of the positive analog signals (with >50 ns risetime) fed to the relevant connectors. Input voltage range is 0 ÷ 4 V. The Mod. V785 N features LEMO 00 connectors for both input and control signals.
-
product
Automated Fibre Loss Test Set
LTS-1500
The LTS-1500 is a small, rugged automated fiber optic loss test set that characterises singlemode fiber links at wavelengths of 1310, 1490 and 1550 nm. It is comprised of a sensitive InGaAs based optical power meter calibrated at six wavelengths with better than -75 dBm noise level plus a stabilised laser light source with up to three selectable wavelengths.
-
product
Oscilloscope: 1.5 GHz, 4 Analog Channels
DSOX4154G
12.1-inch display, capacitive touch screen technology, InfiniiScan Zone touch triggering, 1-million-waveforms/sec update rate, MegaZoom IV smart memory technology, and standard segmented memory
