Refrigerated Chambers
Any insulated compartment where the ambient temperature can be controlled to maintain a required low temperature.
See Also: Chambers, TEM Cells, Acoustic Chambers, Altitude Chambers, Anechoic Chambers, Climate Chambers, Dust Chambers, Environmental Chambers, ESS Chambers, Humidity Chambers, Reverberation Chambers, RF Chambers, Salt Spray Chambers, Sound Chambers, Temperature Chambers, Temperature Humidity Chambers, Thermal Shock Chambers, Vacuum Chambers
-
Product
Walk-In/Drive-In Humidity Environmental Chamber
-
Burnsco Environmental Test Chambers
These custom designed chambers are used for testing large products, vehicles, or batch testing. They offer temperature and humidity simulation capabilities for climatic testing and temperature/humidity cycling whenever there is a need to simulate wide temperature and humidity extremes. They can be made almost any length, width or height.
-
Product
Environmental Stress Screening (ESS) Chamber
ESS
-
Developed to help electronics manufacturers detect product defects and production flaws, Environmental Stress Screening (ESS) forces infancy product failures that would otherwise occur after final assembly and product delivery. ESS’s goal is to improve profitability by eliminating defective products. ESS Systems can meet individual performance needs, product loading, and throughput requirements. Thermotron has the experience to provide the best solution for ESS testing at your company.
-
Product
TSA Thermal Shock Chambers
-
Traditional three-zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air is pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
Product
RF Diagnostic Chamber
DST200
-
The R&S®DST200 RF diagnostic chamber is the ideal environment for RF analysis during development. It supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used at all times during the product design and optimization phase. The R&S®DST200 effectively assists in achieving high first-time pass rates during final type approval, which saves time and money.
-
Product
Stress screening test chambers for temperature and climate
TS and CS series
-
Our based on the modular concept of the standard range of temperature and climatic stress screening test chambers allow you through increased compressor and large fan performance very high temperature change of up to 30 K / min with conventional refrigeration, or to 70 K / min with liquid nitrogen. These devices allow you to very quickly determine the load limits of your test object in fast motion.
-
Product
Benchtop Temperature Chamber | Environmental Test Chamber
-
The first true Hybrid Temperature Chamber/Platform combination called the Hybrid Benchtop Chamber. The floor of the chamber is a completely functioning Hot/Cold Plate, independent or simultaneous with the chamber. Our models come in different sizes: Micro, Small, and Medium thermal Chambers.
-
Product
Temperature Chambers Environmental Test Chambers
-
Proven Traditional Designs, evolved with New Generation FeaturesCyro Chambers come with 1 year Guarantee
-
Product
Altitude Test Chamber
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Morningtest altitude test chamber combines temperature and altitude environments with optional humidity for simultaneous environmental testing. An altitude chamber allows users to control the environmental test chamber temperature while subjecting the product under test to various levels of altitude up to 150,000 feet.
-
Product
Rain Spray Test Environmental Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s rain spray test environmental chamber is also known as rain spray test chamber, it is used to test the water resistance for electronic and electrical products, such as solar lights, garden lights, buried lights, tunnel lights, car lights, fountain lights, the display…etc. It can also provide references for product design and quality control.
-
Product
Humidity Chamber
HCP
-
Does your application temperature lie between 8 C above room temperature and 90C, with controllable humidity? Then the Memmert humidity chamber HCP is unbeatable in price, performance and comfort. The almost unlimited programming possibilities of temperature profiles make ideal environmental conditions for the load possible.
-
Product
Thermal Shock Test Chamber (Three Zone)
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
Benchtop Environmental Test Chambers
-
Benchtop Test Chambers provide superior performance over a wide range of applications. Ideal for testing smaller products such as computer components, these chambers combine superior performance with compact design that is perfect for research and development or personal point-of-use testing.
-
Product
Thermally Protected Ballast Heating Test Chamber
TPB-UL935
-
Working room dimension: 610×610×610mm• Temperature range: RT+10℃～+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)
-
Product
Box Rain Test Chamber
-
Comprehensive box rain test chamber (with swing pipe and right angle tube) is used to test the electric and electronic devices by simulating natural rainfall with spraying water from the water nozzles (holes) on swing pipe or straight tube. To estimate and recognize if the shell or sealing elements of these device could ensure a good condition of working during and after the test. The products are widely used in the industries of light, electrical, electronics, automobile, motorcycle, household electric appliances, electromechanical equipment, instruments and meters, and other industries.
-
Product
Vibration Chambers
ETV-SERIES
-
Environmental Chamber with Vibration Shaker Interface provision consists of Environmental Test Chamber, Vibration Shaker Interface Provision, HMI/PC PLC based Control System etc., This chamber is designed with unique features to meet the control parameters like Temperature, Humidity (optional) and 3 Axis Vibration Controls which are specified in the specification.
-
Product
Pre-Scan Emissions/Immunity Chambers
-
3m pre-scan Immunity/Emissions semi-anechoic chambers are designed to perform ANSI C63.4/CISPR 16-1-4 and IEC 61000-4-3 compliant radiated immunity and emissions measurements. When using this chamber for ANSI C63.4 pre-compliant radiated emissions pre-scan measurements there’s a limited scan height.
-
Product
Walk-In Conditioning Test Chamber
-
Weiber Walk in Conditioning Test Chamber offers an ideal apparatus for conditioning materials at non-ambient temperatures. Now researchers, engineers, and technicians have a simple and cost effective method to condition samples prior to testing. Laboratory Conditioning Chamber is designed for the conditioning of samples prior to testing, provides conditions from 20% to 98% RH ± 2 and 0°C to 94°C ±0.5°C.Conditioning Test Chambers offers ideal humidity and temperature conditions required for testing the effect of environmental changes on the product. The chamber can be widely used to evaluate the durability of various products. Weiber delivers customized products at the most economical rate and within the limited delivery period.
-
Product
TSE-12-A Thermal Shock Chamber
-
Did you think that getting a thermal shock chamber was too expensive, required special utilities, and half your lab-space? The TSE-12 thermal shock chamber is the solution. Only 26 inches wide, the TSE-12 transfers product loads between cold and hot zones with a temperature range of -65°C to 200°C.
-
Product
RF Shielded Chamber
MIL-STD
-
A high performance RF-shielded chamber specifically designed for radiated emissions testing in accordance with MIL-STD-461E/F. This chamber can be used for conducted emissions, conducted immunity, radiated emissions, and radiated immunity testing.
-
Product
Stability Chambers
-
Our stability test chambers are ideal for pharmaceutical, packaging, life science, personal care, medical, biomedical storage, research, and more.
-
Product
Pressure Accelerated Aging Test Chamber (HAST)
-
Guangdong Test EQ Equipment co., Ltd.
- Hyper-Accelerated Aging: Combines high temperature, 100% RH, and pressure to simulate decades of environmental degradation in days.- Precision Control: Triple-redundant PT100 sensors and PID algorithms for<1% pressure fluctuation.- Safety Systems: Auto-pressure release valves, hydrogen gas detection (for battery/polymer tests), and emergency cooling.- Corrosion-Resistant Build: SUS316L stainless steel interior, PTFE-coated seals, and ceramic-coated heaters.- Smart Connectivity: IoT-enabled remote monitoring, predictive maintenance alerts, and compliance with FDA 21 CFR Part 11 data integrity.
-
Product
Walk-In Xenon Lamp Weathering Test Chamber
-
Xenon is one of the noble gases and is a major component of arc lamps and flash lamp and it also has its importance in general anesthetics. One of the major applications of xenon lamp is that it can be used in research applications to simulate the sunlight.
-
Product
Constant Temperature Humidity Battery Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Battery-Specific Thermal Management: Dual-compressor cascade cooling (-40°C stability) and ceramic heaters for rapid high-temperature recovery.- Precision Electrochemical Control: Integrated battery cyclers with CAN/Modbus protocols, supporting SOP (State of Power), SOH (State of Health), and DCR (Direct Current Resistance) monitoring.- Safety-Centric Design-meet Hazard Level: Chambers are designed with Fire-resistant stainless steel interior, fire suppression,nitrogen purge system, and emergency power cutoff for thermal runaway prevention .- Data Acquisition & AI Analytics: Real-time logging of voltage, current, temperature, and pressure via LabVIEW/Python APIs. AI-driven anomaly detection reduces test cycles by 30%.- Energy Efficiency and Energy Storage: Heat recovery during discharge cycles cuts energy use by 25% (ISO 50001 compliant).
-
Product
Reach-In Altitude Test Chamber
-
Weiber Altitude Test Chamber combine temperature and altitude to test basic components or subassemblies designed for use in a variety of industries. With altitude test chambers, user can control the temperature environment for testing while simulating various altitudes from site level to 10,400 meters (25kPa). Altitude testing may be continued without temperature control up to 600,000 meters (0.1 kPa).High Low Temperature Altitude Test Chamber is used to test temperature and low-pressure altitude conditions simultaneously. Two common applications of High Low Humidity Altitude Test Chamber are testing of avionics or other aerospace equipment to simulate actual conditions, and simulate high-altitude conditions found in mountainous regions or other regions. All models are factory tested, with an ergonomic and maintenance cum user-friendly design. These CE approved test chambers are created with multi-layered insulation with double vapour barrier is of low 'K' factor, high density and of non-hygroscopic in nature. Weiber test chamber are made in accordance with the international standard. Weiber Test Chambers are GMP complaints and are also ISO and NABL certified.
-
Product
Burn-in Room and Aging Test Chamber
-
Isolated type of burn-in room features: ●Separate the product and loading area, easy to control temperature and maintain. ●Temp. range: 40-70ºC±3/±5ºC, ●Temp. constancy: ±0.5ºC ●Uniformity: ±3ºC ●Test frame materials: painted stainless steel or a combination of forming aluminum ●Insulation: with PU foam ( doors with double glazing ) insulation, so that the internal temperature is not subject to external factors, to achieve power saving effect ●Product hierarchy placement, Selection of layer height in accordance with the requirements, convenient access ●Computer monitoring system is optional. ●Noise level:≤75dB Application Suitable for all kinds of electronic products, especially for products with heating characteristics Product and loading area should be separated Large-scale production
-
Product
Chambers
-
Our EMC anechoic chamber solutions paired with the Frankosorb® unique non-combustible absorber technology, we are the first choice when it comes to reliable and state-of-the-art test facilities. Our solutions are adapted to every kind of vehicle and its different power train units, incl. hydrogen, gasoline, petrol, from small-sized passenger cars up to large and heavy-weight transport vehicles.
-
Product
Altitude Test Chambers
-
Altitude chamber testing is important for manufacturers of products that might be shipped via air. It is especially important for defense and aerospace applications where pressure and vacuum conditions are even more intense. Our altitude test chambers simulate a variety of environmental conditions including temperature, altitude, humidity, and vibration for the rigorous testing standards of combined environment.
-
Product
Salt Spray Chamber
-
Wewon Environmental Chambers Co, Ltd.
Salt Spray Chamber used for testing the corrosive resistance of products whose the surface was treated with paint, electroplating, inorganic and organic film, anode handling, anti-rust oil, etc. Wall-mount spray system can be freely placed without occupying any effective test space.With imported quartz nozzle, it has the characteristics of smooth interior wall, accurate angle and no crystalline in long-time spraying. Distinctive spring door hinge design makes the chamber door easy to open and close. The inner and external shell of the chamber is made from PVC materials; Easy launder no leakage phenomenon
-
Product
Reach-In Stability Chambers
-
The PH series chambers are designed for performance specifications exceeding FDA and ICH requirements.
