Backplane Test
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB112
-
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slot, one PCIe x16 slot, and ten 32bit/33MHz PCI slots
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Test System
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
CATR Benchtop Antenna Test System
ATS800B
Test System
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
14-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB100
-
The FAB100 features one CPU card slot, four ISA slots, four PCI-E x1 slots, one PCI-E x16 slot, and four 32bit/33MHz PCI slots. This PICMG 1.3 backplane also supports a built-in 24-pin ATX power connector. Furthermore, the FAB100 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491 and AX6145, to house the FAB100 and any customer's industrial integrations flexibly.
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB113
-
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x1 slot, one PCIe x16 slot, and four 32bit/33MHz PCI slots
-
Product
Test Port Cable, 1 Mm
11500K
Test Port Cable
Connect test ports to devices, fixtures, or probe tips with this 20-cm cable featuring a return loss of 16 dB minimum
-
Product
Analog Backplanes
MSXB 031
-
Analog Backplanes provide expansion slots to accommodate compatible analog external boards. Analog Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical.
-
Product
PCI Express Expansion Backplane
SKU-076-0X
-
PCI Express Expansion backplane was designed as a universal solution for Desktop or Laptop host computer expansion. It allows adding up to four additional PCI Express boards to the host computer. Expansion backplane can be placed inside any general-purpose computer chassis, and connects to the host computer via 5ft (or 10ft) CAT6 cable.
-
Product
EBIRST 50-pin D-type To 37-pin D-type Adapter
93-005-418
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Automated Multi-Functional Tester
QTouch 1408 C
Functional Test
Qmax Test Technologies Pvt. Ltd.
QTouch 1408 C – Automated Multi-Functional Tester with in-built camera is designed to make automatic image capturing and probing of electrical signals with ease and speed especially in PCBs with high density/high pin count device that are mounted on the PCB. It is designed to move on X, Y, Z directions making it possible to probe every component as close as 20 mils. Easy tagging feature allows the user to get the real time XY coordinates using the library information with minimal intervention. CAD import feature is available for Auto Test Generation/to extract the XY coordinates from the CAD data. Qmax Automated Multi Functional Tester can perform Board level functional test of a PCB and guided probe / Back tracking diagnostics utility to reliably test Digital, Analog and Mixed Signal PCBs and fault isolation to the PCB level or component level.
-
Product
Wallmount Industrial Chassis Supports 10-Slot Backplane
RK-609B
Chassis
- Supports 10 slot PICMG backplane- Two 5.25" and two 3.5" external drive bays, one internal 3.5" drive bay- Upper cover with captive screw- Drive bay with shock and vibration resistant design- Replaceable and easy-to-clean air filter- 12cm cooling fan (85CFM)- Two USB and one PS/2 keyboard connectors on front panel
-
Product
OpenVPX Backplanes - 3U, 6U
-
OpenVPX provides a versatile, high-speed architecture utilizing the rugged Eurocard form factor. There are backwards-compatibility options with VME/64x with hybrid backplanes.
-
Product
In-Circuit Testing and Test Engineering
-
5184 Test NodesHPUX or Windows60 Mhz ASRU Frequency Counter, Timer10 Mhz Clock, 6 Mhz data ratesVector Test for VLSI, PLCC & ASICSTestjet and VTEP Vectorless TestingAdvanced Boundary ScanSilicon Nails AvailableSeries V upgradeable
-
Product
Drive Controller Function Test – Universal Functional Test System for Industrial Electronics
Functional Test
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
Product
VME64x VITA 1.7 Backplanes
-
Atrenne VME64x VITA 1.7 backplanes comply with ANSI/VITA 5.1, include a 12-layer low noise striplinedesign with outside layers, which incorporates a chassis ground EMI shield and are available in customer configurations.
-
Product
3U 12-slot VPX Backplane Aligned To SOSA 1.0
1OVX312AFQ-xxxx
-
3U 12-slot backplane with profiles aligned SOSA. It is designed to meet the U.S. Army’s C5ISR Modular Open Suite of Standards (CMOSS), and supports high-speed signals on all data paths and VITA 67.3 and VITA 66.5 connectors.
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
Test System
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
Test Fixtures & Test Sets
-
Keysight test fixtures are used to hold electronic components or materials (physically and electrically) in order to perform various measurements. Keysight offers a variety of test fixtures from Parametric, Dialectrice, Liquid test fixtures and more.Some of our test fixtures allow you to connect directly to your measurement instrument, while others require various adapters.
-
Product
Test Fixture, Axial And Radial
16047A
Test Fixture
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
-
Product
Automated Compliance and Device Characterization Tests
N5990A
Test Platform
The Keysight N5990A test automation software platform is the most powerful tool for serial and multi-lane gigabit testing. It is the unique universal platform for testing a wide range of digital buses such as PCI Express, USB, HDMI or MIPI. The same graphical user interface and operating principles are used for all applications. This boosts productivity, especially when testing devices which support multiple digital buses. The N5990A can be tailored to your individual test needs with the flexible test sequenzer and controls all instruments needed for your tests. The configurable database interface of the N5990A test automation platform enables the convenient storage of all test results. A web interface allows an effective and easy operation. Custom calibration and test procedures can be implemented easily with User Programming.
-
Product
Compact PCI PICMG 2.20 Backplanes
-
Comtel Electronics offers the Serial Mesh Backplanes PICMG 2.20 High Speed mesh connections on ZD connectors (P4 area). Fully compliancy with PICMG 2.0 Rev 3.0 Specs & 2.20 Spec.
-
Product
Desktop PCB Test System
BOARDWALKER 9627
Test System
Qmax Test Technologies Pvt. Ltd.
QT9627 is a cost effective entry level model Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test .Maximum Digital Test Speed 10MHz in the QT9627 .
-
Product
Test Contactors
OCwype
-
Johnstech International Corporation
The new OCwype™ contactors are the latest in a long line of Johnstech products that allow companies to reduce costs and time to market.
-
Product
Voltage Testing
VisualDetect series
-
Hachmann Innovative Elektronik
With the VisualDetect line you get a type series of handy, exact and easily operated voltage detectors and maintenance testers.
-
Product
Test Engineering
-
With a thorough knowledge of various internet connectivity products, Xebrium’s team of Software Engineers, Network Engineers, and Test Engineers are relied upon to implement and rigorously test networking and wireless product.
-
Product
Battery Testing
-
Weshine Electric Manufacturing Co., Ltd
The DC test method is adopted to simulate the actual use of the battery in a real and objective way, which can effectively eliminate the hidden dangers such as deficiency, deficiency and connection failure between batteries while measuring the internal resistance of the battery.
-
Product
Test & Development
-
Taking a new board level product or system from concept to deliverable requires feature-rich development and testing tools. Elma's wide range of Type 15 (desktop), Type 32 & D-Frame (portable/desktop) and Type 39E (development frame) chassis for VITA and PICMG bus architectures provide the platforms necessary to meet your needs.
-
Product
In-House Testing
-
Aerodyn’s state of the art test facility features vast capabilities for new product development and testing to meet our customers’ needs. By coupling our extensive design, fabrication, and instrumentation capabilities, along with our LabVIEW certified engineers, Aerodyn offer the utmost support to allow for very quick test setups and delivery of results.
-
Product
Test Automation System for Engine Testing
STARS Engine
-
With a wide range of user-friendly features, STARS Engine can run the most complex of tests with a simple press of a button making your test operation effective and efficient and above all, reliable. STARS provides all the features you need to run a wide range of Engine Test Programmes from simple manual testing to dynamic automatic tests, all from a single, simple to use user interface. STARS is designed to be run in either stand-alone operation for a single test stand or as a cluster of systems to allow a test field to be run more efficiently. In both cases the user works in the same way and uses the same interface.
