Transformer Turns Ratio Testers
See Also: Transformer Testers, Transformer Turns Ratio
-
Product
Primary Injection Testers
AT-10B
-
ETI’s AT-10B autotransformer steps-down 480V outputs to 240V outputs. This portable autotransformer allows ETI’s PI-1600 or PI-800 circuit breaker testers to be used at full-capacity on 240 and 480 VAC lines. The unit provides 240 VAC at 10 kVA, is housed in a rugged ABS enclosure approximately 22″ x 11″ x 22″, and weighs less than 125 lbs.
-
Product
Needle Flame Combustion Tester
-
Shanghai Dean Electrical Co., Ltd
The touch screen control needle flame combustion tester is developed according to the requirements of the needle flame combustion test in the standard
-
Product
Inmarsat-C Physical Layer Tester
CPLT
-
Square Peg Communications Inc.
Square Peg Communications Inc.’s Inmarsat-C Physical Layer Tester (CPLT) is a software application that runs on the generic high-rate Physical Layer Tester (PLTH) platform. The CPLT supports testing of the physical layer performance and protocol implementations of Inmarsat-C Mobile Earth Stations (MESs) and Land Earth Stations (LESs).
-
Product
Component Testers
-
Unlike other handheld instruments such as LCR meters that make measurements using an AC signal with a specific test frequency, the 830C measures capacitance by applying a constant current that briefly charges, then discharges the connected capacitor.
-
Product
Tensile Strength Tester
DRK101C
-
Shandong Drick Instruments Co., Ltd.
DRK101C tensile strength tester is designed adopting modern mechanical design concept and human body engineering design criterion with advanced microcomputer processing technology .It has a novel design, excellent performance, and beautiful appearance.
-
Product
Insulation Oil Tester
KVJS-7000
-
KV Hipot Power Test Equipment Co.,Ltd
Insulation oil dielectric loss and resistivity tester is mainly used to test dielectric loss factor and resistivity of insulation oil and liquid insulation medium.
-
Product
Battery Internal Resistance Tester
HDGC-3915
-
HD Power Test Equipment Co.ltd
Battery Internal Resistance Tester is designed using the advanced AC discharge measurement method to test accurately voltage and resistance of battery. It is strictly designed to evaluate battery performance, state and life-time, which maintain all stationary power systems including Uninterruptible Power System. Battery Internal Resistance Tester can proceed the measurement in a group and in a single section of battery. With accurate testing of resistance and voltage, it gives an indication of battery capacity and technical status. The measurement data can be read on the instrument display directly. And it can also be uploaded to PC simply by using the USB drive. With the analyzing software, you could not only keep a record of the testing result but also have detailed analyzing for the status of batteries in different testing conditions.
-
Product
Hand-Held/Digital Load Tester
6030
-
• Full 125 Amp load tests 12 Volt batteries, alternators and starters on all type of vehicles• PATENTED• Made in USA of US and Global Components
-
Product
ATX Power Supply Tester
Dr.Power II
-
Thermaltake Technology Co., Ltd.
Designed from the ground-up, it supports every ATX power supply available today up to ATX12V v2.3. - Oversized LCD panel that accurately shows the value of each specific power rails (within one-tenth of a volt). - Accurate voltage indicating for +12V/+5V/+3.3V/5VSB/-12V. - Built-in output connectors diagnostic system, low-voltage, high-voltage, no voltage, PG alarm systems.
-
Product
Helium Leak Testers
-
Yamaha Fine Technologies Co., Ltd.
Yamaha Fine Tech's proprietary low vacuum test realizes highly reliable measurement. With our proprietary low vacuum chamber system and helium gas detector, highly reliable inspections are conducted. Easy operation and easy maintenance are realized by a full fail-safe and sophisticated control system.
-
Product
Fiber Optic Tester
OPTOWARE-FTTx-PON Test Solutions
-
FTTx networks using PON technology can be characterized and maintained every step of the way using very simple new fiber-optic test equipment.
-
Product
Battery Impedance Tester
-
Weshine Electric Manufacturing Co., Ltd
The DC test method is adopted to simulate the actual use of the battery in a real and objective way, which can effectively eliminate the hidden dangers such as deficiency, deficiency and connection failure between batteries while measuring the internal resistance of the battery.
-
Product
Apparent / Bulk Density Tester
Bulk Density Tester Series
-
The Apparent Density Tester - Bulk Density Tester series testers are used to measure apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders. There are three methods according to ASTM D 1895 that are applicable to various forms of these materials that are commonly encountered - from powders and granules to large flakes and cut fibers. The apparatus consists of a measuring cup which is polished inside and a funnel.
-
Product
Hardness Testers
-
Dalian Taijia Technology Co.,Ltd
Digital durometer for shore hardness testing pocket size model with integrated probe● Test scale: shore hardness● Standards: DIN53505, ASTMD2240, ISO7619, JISK7215● Parameters displayed: hardness result, average value, max. value● Measurement range:0-100HA(HD)(HC)● Measurement deviation:＜1%H● Resolution: 0.1● Auto switch off● With RS232C interface● Operating conditions: 0℃ to 40℃● Power supply: 4x1.5V AAA (UM-4) battery● Battery indicator: low battery indicator● Dimensions: 162x65x38mm● Weight (not including probe):173g● Application:Shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials.Shore D is designed for plastics, Formica, Epoxies and Plexiglass.shore C is designed for various foam and sponge.
-
Product
Battery Testers
-
Shanghai Beha Electronics Co., Ltd.
*can measure the resistance of rechargeable batteries and DC voltage.*can also test Ni-cd, Ni-MH, Li-ion batteries.*DC Voltage measurement.*4-wire resistance measurement.
-
Product
Next Generation Battery Tester
-
Upgrade to Maccor's newest test platform, The Series 6000. While maintaining all of the features of Maccor's high precision hardware, the Series 6000 adds an element that will elevate your testing. The new high-speed control and data collection capabilities are impressive.The Advanced Multi Level Pulse ("AMLP") allows you to create the most complex pulse profiles available.
-
Product
Leeb Hardness Testers
-
Your product description goes here. Leeb hardness tester application: Leeb hardness tester is for metal. Die cavity of molds,Inspection of bearing and other mass produced parts on a production line,Failure analysis of pressure vessel, steam generator and other equipment, Inspection of installed machinery, permanent parts of assembled systems and heavy work pieces.Rapid testing in large range and multi-measuring areas for large-scale work piece.
-
Product
Battery Discharger & Capacity Tester
IDCE-CT
-
Fuzhou Fuguang Electronics Co., Ltd.
Each wireless module can monitor 4 batteries simultaneously comparing with the traditional method that each module only canmonitor 1 battery, the new wiring operation become easier because the quantity of new modules needed is only a quarter of old-fashioned modules.
-
Product
Waterproof Eco Tester
EcoTestr pH 2
-
From the market leader of testers comes the EcoTestr pH 1 & pH 2 – a new range of value-for-money, quality pH tester series designed for fuss-free pH measurements. Accurate, and easy to use, these testers are ideal for quick pH checks in hydroponic gardening, aquaculture, agriculture, pools, simple lab work and other water/wasterwater applications.
-
Product
Paper Thickness Tester
DRK107A
-
Shandong Drick Instruments Co., Ltd.
DRK107A Paper Thickness Tester is professionally applied to testing the thickness of paper specimens.
-
Product
SOLUBLE SALT TESTER
-
The PosiTector SST Soluble Salt Tester measures the concentration of soluble salts (salt contamination) on metal surfaces in accordance with ISO 8502-6, 8502-9. View Video
-
Product
Cable Testers
-
AEMC's line of hand-held cable testers provides direct and simple push button operation. The testers indicate faults, cable length, common wiring faults and more. All models feature a large, blue electroluminescent backlit display.
-
Product
Mixed Signal Automated Tester
MSAT
-
Whether you are testing radar systems for the Department of Defense (DoD), or the next actuator circuit card for aircraft landing systems, ARC’s Mixed Signal Automated Tester (MSAT) offers flexible automated testing capabilities for nearly every budget.
-
Product
CELL TESTER
SPOTLIGHT
-
SpotLIGHT was designed to minimize maintenance and to significantly reduce downtime. The lifecycle of its contacting system is longer than that of standard systems currently available on the market, thus substantially reducing TCO.
-
Product
Drop Weight Tear Tester
DWTT
-
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
Product
Single-Functional Testers
3122
-
The MI 3122 SMARTEC Z Line-Loop / RCD is designed specifically for live circuit testing. The instrument contains integrated characteristics of fuses and RCDs for the evaluation of test results. The online voltage monitoring system allows the operator to control what is happening on three simultaneous voltages in real-time. The bright red and green PASS / FAIL lights and help screens for each measurement make the handling of the instrument easy and clear. All the results can be quickly saved on the instrument and then downloaded via the optional A 1291 EuroLink PRO or A 1290 EuroLink PRO Plus software for evaluation and professional report generation after testing.
-
Product
Voltage Tester
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Voltage Tester is a testing instrument used for electrical power testing purposes. It is mainly used for detecting the presence of AC voltage in or around the object or surface and is very easy to operate.
-
Product
Case Depth Hardness Tester
HTD-4000
-
HTD 4000 is used to measure case depth and is capable of verifying case depths ranging from 0.4mm (16 thou) up to a maximum of 2.5 / 2.8mm (100110 thou). Our system utilizes a new and very advanced principle based on the continuous measurement of the electrical resistance in relation to the working load applied. Our design meets the demands of the heat treatment industry. HTD 4000 is equipped with a big stand to enable the testing of large work pieces having overall dimensions up to 550mm (22") in height and 350mm (13.8") depth
-
Product
Oxygen Permeability Tester
T-OPT Series
-
Oxygen Permeability Tester - QT-OPT series is ideal for industrial application laboratory testing of material for Oxygen permeability testing for quality control, research and development.
-
Product
Leakage Current Tester and Clamp-On Earth / Ground Resistance Tester
-
10µA Ultra High ResolutionLarge Conductor Diameter (30mm)AC Current in 5 Ranges (40mA, 400mA, 4A, 40A, 60A)Wide Frequency Response (40Hz-1KHz)ACA, ACV, Ω and ContinuityLarge 3¾ Digit LCD (4000 Count)40 Segment Fast Bargraph Display (20 times/sec.)Data Hold and Max / Min HoldRelative Measurement600 Vrms Overload Protection in Resistance Range
