Hall
a measurable transverse voltage which occurs when current flows through a conductor in a magnetic field.
-
Product
Photonic Hall Effect
HMS7000
-
Classic hall effect measurement system is to read voltage difference made between both diagonal sides, when flowing current and applying magnet field strength, in perpendicular to flowing current direction. - Photonic hall effect measurement is to read various electrical properties by illuminating light of “various range of wavelength” on the sample, in addition to flowing current and applying magnet field strength. - It is great to see “RGB (Red, Green, Blue), Light intensity vs carrier density, carrier mobility, resistivity, hall coefficient”
-
-
Product
Hall Effect Sensors
906
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Bi-directional option 906B
-
Product
Quantum Hall Resistance System
-
Measurements International Ltd.
Quantum Hall System, System Accuracy to < 0.003 ppm with CCC Model 6200A, System Accuracy to < 0.015 ppm with DCC Model 6020Q, 5 Tesla Standard System Magnet, Stable Controlled Sample Environment, Base Temperature < 3.6 K, Low Operating Costs, Direct Transfer to 100 Ω, 1 kΩ, 10 kΩ, and 100 Ω Standards, System Range 0.1 Ω to 100 kΩ, Graphene Device Values 1 kΩ, 10 kΩ, 12.9064037 kΩ and 100 kΩ, Triple Sample Device Mounting.
-
-
Product
Gridless End-Hall Ion Sources
-
Veeco's Gridless End Hall Ion Sources provide high beam current for vacuum coating processes.
-
Product
Hall Sensor Board with I2C Interface
050-279
-
Version: +5V/90A +3,3V/25A +12V/60A +12V/60A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Closed Loop Hall Effect Current Sensors/Transducers
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor
-
Product
Closed Loop Hall AC/DC Current Sensor
CYHCS-SH
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can beused for measurement of DC and AC current, pulse currents etc. The output of thetransducer reflects the real wave of the current carrying conductor.
-
Product
USB Hall Probes
-
MAGNET-PHYSIK Dr. Steingroever GmbH
The USB Hall probe is simply connected to a computer and operated using easy-to-understand software. No additional measuring device is required to measure the magnetic field strength. You can download the "USB Teslameter" software for Windows here. A Linux version is available from us on request.
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Product
AC/DC Hall Effect Sensors
-
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
-
Product
Hall Effect Measurement system
HMS-5000
-
Constant current source + Van der Pauw method terminal conversion system
-
Product
Super high temperature hall effect measurement system
-
Super high temperature hall effect measurement system that is useful to flow gas into chamber with sample. - Newly developed furnace that makes it possible to increase over 800 and use for measuring hall effect. - Gas flow control system in order to flow various gas. - Sample holder for high temperature. (keep the good contact on 800) - High Temperature control system (DC power) On condition of specific temperature with gas flow , new semiconductor materials have been developed to see electrical property's change.
-
Product
Hall Effect Magnet Kit
-
Permanent magnet - Neodium materials - +/- 0.03Tesla deviation can be made in a process of assembling magnet. - However, we indicates correct tesla strength measured by gaussmeter, before shipping magnet kit.
-
Product
Rotary Hall Effect Sensor
-
The output of the Rotary Hall-effect sensor is a voltage which changes in direct proportion to the shaft angle. The sensor is non-contact, using Hall elements to determine the angle of a magnet. The magnet is either mounted in a shaft integral to the sensor or can be mounted externally to the sensor.
-
Product
Hall Effect Proximity Switches/Sensors
-
ChenYang Technologies GmbH & Co. KG
A Hall Effect proximity switch is a non-contact electronic switch, which consist of a permanent magnet or ferromagnetic part as trigger intermediary and a Hall Effect sensor IC. The Hall sensor IC detects the change of the magnet field when the permanent magnet comes in the close proximity to it and generates an electric signal. This signal is amplified and rectified to control the output signal of the switch.
-
Product
Hall Sensor Board with I2C Interface
050-280
-
Version: +24V/60A -24V/60A -5,2V/90A -2V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Closed Loop Hall AC/DC Current Sensor
CYHCS-D8
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current in the carrying conductor.
-
Product
Hall Effect Thickness Gage
Magna-Mike 8600
-
The Magna-Mike® 8600 is a portable thickness gage that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
Product
Hall Effect Sensor
-
The hall effect sensor products are manufactured according to international standards. Being an ISO 9001:2008, ISO 14001 and OHSAS 18001 certified company, DER EE is capable of designing and producing superior products to the highest standards of customers' requirements. Hall effect sensors we provided are a device containing both the sensor which produces a very low signal level and contains the vacuum tube amplifier and a high gain integrated circuit (IC) amplifier in a single package. hall effect sensor offer many applications to sense position and motion, to control electric motor control, to sense wheel rotation and so on.
-
Product
Hall Effect Sensor
907 XP (Explosion Proof)
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
Product
Hall Sensor Board with I2C Interface
048-368
-
Version: +5V/60A +5V/60A +3,3V/25A +12V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Group3 Hall probe
-
The Group3 Hall probe produces an analog voltage as its output signal, corrected for temperature effects and non-linearities, producing a signal accurate to within 0.05%, from -1 to +1 T, over 10 to 50 deg C. Group3 can offer different field and temperature ranges, and custom probe dimensions.
-
-
Product
Hall Effect Sensors
-
A new range of sensors based on closed loop hall effect technology, for measuring and monitoring of e.g. secondary transformer overload or shortcircuit detection, DC link from ground fault and overload, motor overload.
-
Product
Hall Effect Measurement system
HMS-5500
-
Variable temp : 80K ~ 350K (model# : AMP55T ) - HMS-5500 can be compatibly used with both low temp magnet kit (model# :AMP55T) and high temp magnet kit (model#: AHT55T5, upto 500dC) - Below image is to show model# HMS-5500 + AMP55T, for low temp.
-
Product
Hall Sensor Board with I2C Interface
050-382
-
Version: +5V/15A +12V/15A -5V/15A -12V/15A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Speed Sensors
-
DHE (Differential Hall Effect) sensors give an output when subjected to a changing magnetic field. The field is set up by a magnet inside the sensor body and changes when ferromagnetic teeth are passed beneath the sensor (no magnets are required in the target). To improve noise resistance, the sensor has two Hall effect elements and only responds to changes in magnetic field strength corresponding to tooth passing frequencies above 15Hz. As each tooth passes the sensor, the digital state of the output changes.
-
Product
C Series Frequency Input Module
-
The C Series Frequency Input Module is designed to acquire isolated frequency inputs from magnetic pickup sensors, variable reluctance sensors, Hall effect sensors, and other transducers with a frequency output. Additionally, the C Series Frequency Input Module provides isolation, configurable thresholds, selectable filtering, and embedded counter measurement logic. These measurements can be synchronized with other frequency, analog, digital, and counter measurements in a single acquisition.
