Hall
a measurable transverse voltage which occurs when current flows through a conductor in a magnetic field.
-
Product
Current Sensors
-
Measurlogic offers an array of current sensors for every need, including split core, solid core and Rope current transformers (CTs); DC Shunts and Hall Effect Sensors. All of our electrical sensors are designed with an easy, un-intrusive installation in mind. With a low cost and high accuracy guarantee, we provide top of the line solutions for measurement and cost savings for residents and business owners alike.
-
Product
Position Sensors
-
Position sensor is a device that can detect the movement of an object and converts these into signals suitable for processing, transmission, or control. TE Connectivity (TE) is a leading manufacturer of industrial linear and angular position, tilt and fluid level sensors. Both off -the-shelf and custom position sensing solutions are available featuring our core technologies, including inductive, potentiometric, magnetoresistive, hall effect, reed switch, electrolytic and capacitive sensing.
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Product
CEMS
FMD 02
-
IMR Environmental Equipment, Inc.
The continuous measurement of velocity and temperature of gas flows is much important at operation of a system with flowing gases (e.g. hall outlet air, exhaust etc.).
-
Product
Hall-Sensor Board with analog output
041-970
-
The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1200B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Axial-Hall-Probe
-
For the Gaussmeters are several axial Probes with different dimensions and sensitivity available.
-
Product
Isolated Hall Effect Current Sensors
-
Isolated Hall Effect current sensors provide accurate high bandwidth current sensing. Vektrex offers models to 320A. For use, the 50-ohm voltage output is connected directly to an oscilloscope or data acquisition system. VCS sensors are magnetically isolated like clamp-on oscilloscope probes. With secure cable attachment, repeatability is ensured.
-
Product
Measuring Device For Measuring Residual Magnetism
Teslameter M-Test LL
-
Measure residual magnetism on ferromagnetic materials precisely and reliablyquick detection of residual magnetismreproducible measurement results through automatic storage of the maximum valuesdefined measuring distance of 0.5 mm from the Hall probe to the measuring surfacemeasuring static and alternating magnetic fieldsselectable units: A / cm, Gauss, mTwear-resistant test sample
-
Product
AC / DC Current Probe, 100 MHz, 30 Arms
N2783B
Oscilloscope Probe
The N2783B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
-
Product
USB Hall Probes
-
MAGNET-PHYSIK Dr. Steingroever GmbH
The USB Hall probe is simply connected to a computer and operated using easy-to-understand software. No additional measuring device is required to measure the magnetic field strength. You can download the "USB Teslameter" software for Windows here. A Linux version is available from us on request.
-
Product
Non-Contact Type Magneto-Electric Rotation Detector
MP-9820
-
MP-9820 is a magneto-electric-rotation detector using an internal hall element, a permanent magnet, DC amplifier, and voltage regulator in its compact body. Using MP-9820 in combination with detection gear enables deriving stable rectangular waveform from ultra low speed all the way through high speed. (1 Hz to 100 kHz)MP-9820 finds wide range of applications and rotational measurement objects by using with TM-3100 series tachometer and FV-1500 FV converter.
-
Product
Reference Magnet
-
Reference magnets generate a homogeneous magnetic field in an air gap. They are mainly used to calibrate hall probes for their full scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using reference magnets.
-
Product
Melting Furnace
-
Napco Precision Instruments Co
*It can be used in melting powder (more than 1g)*Fast speed, less loss, simply operating. High efficiency.*Suitable for factory, exhibition hall, old material recycling, jewelry repair,shop, the pawn etc.
-
Product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
Product
Miniature Magnetic Field Sensor
FLC 100
-
Complete miniature fluxgate magnetometer can be used in any application where the sensitivity of Hall- or MR-magnetometers is not sufficient, e. g. measurement of the earth's field, detection of AC field from power lines, vehicle detection, compass navigation, and many others. Due to its low price and low power consumption ideally suited for multi-sensor array systems.
-
Product
Transmittance Dust Measuring Devices
-
Maintaining a clear sightline even when dust concentrations are highTransmittance dust measuring devices transmit light through the entire duct. With this type of measurement, light attenuation indicates the concentration of dust inside the duct. These measuring devices are specially designed for medium to high dust concentrations and large duct diameters. Consequently, they are equally suited to emission and process monitoring as they are to hall monitoring applications.
-
Product
Current Probe With Hall Effect Technology
CP 35
-
The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Hall Effect Measurement Equipment
HEM
-
The physical quantity of Hall Coefficient, Hall Mobility and Carrier Density etc. can be investigated by measuring at room temperature voltage occurred perpendicularly to the both magnetic field and constant-current when flowing constant-current perpendicularly to magnetic field from current source while applying magnetic field to sample set at the center of magnetic field of magnet.
-
Product
Vehicle Actuator Tester
7651
-
Peaceful Thriving Enterprise Co Ltd
This device is design to test electronic components actuate by magnetic field or electronic magnetic field. Devices like actuator, ignition coil, AC generator, indoor air blower, valve controller EGR (exhaust gas control), injector, spark plug, relay and hall effect sensor can be tested.
-
Product
Single Axis Magnetometers
MAG Serie
-
Macintyre Electronic Design Associa
The µMAG series is the premiere, handheld instrument for the precision measurement of the vector components of weak static and low frequency magnetic fields. The superior stability, linearity and accuracy of the uMAG, compared to Hall Effect or Magnetoresistance base instruments, make it the only choice for high quality low magnetic field measurements and best choice for gerneral purpose magnetometer applications.
-
Product
Digital Gauss Meter
-
STAR TRACE SOLUTIONS PVT. LTD.
Digital Gauss meters are hand held devices which are used to measure D.C magnetic field using Hall Probes. The Gauss meter is available in two different ranges and helps in quick calibration. As the Digital Gauss meter is easy and simple to handle it is extensively used in industries which require measurement of magnetic field.
-
Product
Geomagnetometer w/Hall Probe
IDR-321
-
Integrity Design and Reseach Corp.
Typical applications: Earth's field vector measurement, air shipment inspection, mapping & recording field perturbations, etc.
-
Product
Zero Field Cavity
-
Zero field cavities generate a zero magnetic field in an air gap. They are mainly used to calibrate hall probes for their zero scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using Zero Field Cavity.
-
Product
Resistivity and Hall Effect
-
The Resistivity System allows the user to make Resistivity and Hall Effect measurements in the range of to M. Samples are mounted on special platforms inside the VTI with contacts made to the sample according to the customer's requirements.
-
Product
Guarded Insert For PPMS®
-
The Lake Shore guarded insert can be used alone or with one of our PPMS Hall measurement packages that include the MeasureReady® M91 FastHall controller. Cut your measurement time up to one-half with the M91. Measurements are so fast that time-dependent misalignment errors are eliminated using the patented FastHall™ measurement technique.
-
Product
Sport Sensor Range
-
DHE (Differential Hall Effect) sensors give an output when subjected to a changing magnetic field. The field is set up by a magnet inside the sensor body and changes when ferromagnetic teeth are passed beneath the sensor (no magnets are required in the target). To improve noise resistance, the sensor has two Hall effect elements and only responds to changes in magnetic field strength corresponding to tooth passing frequencies above 15Hz. As each tooth passes the sensor, the digital state of the output changes
-
Product
Cryogenic Probe Station
CPX-VF
-
The Lake Shore CPX-VF probe station enhances the standard probe station capabilities with the addition of a ±2.5 T vertical field superconducting magnet. It can do all the standard C-V, I-V, microwave, and electro-optical probing of the CPX, plus out-of-plane vertical field superconducting magnetic measurements. Researchers can use it to perform Hall effect measurements and test magneto-transport parameters. The CPX-VF is one of Lake Shore’s premium probe stations for combining microwave measurements with magnetic field.
