Environment Chambers
simulate surrounding conditions test target will be exposed to in application.
-
-
Product
Salt Spray Chambers
MX-9200
-
LR Environmental Equipment Co. Inc.
A high reliability thermostatic temperature controller maintains the salt solution at a preset controlled temperature in a reservoir within the double wall construction. The salt solution is introduced into the chamber through an atomizing nozzle. The nozzle can be calibrated by us to perform to MIL-STD-19500B, paragraph 40.8 and other specifications. This specification requires that a salt residue be deposited on the specimens, in addition to generating salt fog atmosphere.
-
Product
Thermally Protected Ballast Heating Test Chamber
TPB-UL935
-
Working room dimension: 610×610×610mm• Temperature range: RT+10℃～+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)
-
Product
TSE-12-A Thermal Shock Chamber
-
Did you think that getting a thermal shock chamber was too expensive, required special utilities, and half your lab-space? The TSE-12 thermal shock chamber is the solution. Only 26 inches wide, the TSE-12 transfers product loads between cold and hot zones with a temperature range of -65°C to 200°C.
-
Product
Software Communications Architecture (SCA) Development Environment
-
NordiaSoft products enable embedded systems developers to rapidly create software artifacts using the Component Based Development (CBD) and Model Driven Engineering (MDE) paradigms. Implementing the Software Communications Architecture (SCA), an open specification adopted internationally and evolved through the Wireless Innovation Forum (WInnF), a consortium of major radio manufacturers, academic, research laboratories and government authorities, the NordiaSoft products provide multiple advantages over other commercially available solutions for embedded systems:
-
Product
Rapid Temperature Change Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
The Wewon’s rapid temperature change test chamber is equipped with two 1.5 kW French Tecumseh compressors, Cooling capacity temperature change rate can be 3℃ / min. The machine can carry out on-line product quality inspection task according to the specified temperature change rate. The volume and wind speed will be adjusted automatically, This makes the temperature in the test area is evenly distributed. Through an electronic expansion valve, The surface temperature difference of the tested product is suppressed, and the linear control precision is realized.https://www.wewontech.com/rapid-temperature-change-test-chamber/
-
Product
Drive-In Chambers
-
Environmental testing of automobiles requires additional consideration of the facility where the chamber will be installed, and its planned use. Test methods for vehicles can include additional conditions besides temperature and humidity in an attempt to simulate real-world conditions.
-
Product
TSD-101-W Chambers Chambers
-
ESPEC developed the TSD-101-W with an large interior of 28"x16", while strictly limiting the overall size of the system. The footprint is reduced by 40%, as well as lowering power demand by 60% compared to conventional units.
-
Product
High Accuracy Low Pressure Environment Pressure Switch
P100G
-
The P100G High Accuracy Low Pressure Environment Pressure switches are ideal in light pressure applications where precision of setpoint must be high and repeatability low. These switches are commonly used in natural gas well heads, natural gas generator sets, and air applications like forced draft blowers. The P100G can be used both in dry indoor applications or within an enclosure.
-
Product
Electromagnetic anechoic box/Shield box/Anechoic chamber
-
The necessity of a wireless system test has risen by the spread of recent wireless telecommunication equipment as shown in cellular phone, wireless LAN, RF-ID tag and ETC (Electronic Toll Collection system). It is necessary for a wireless test to be performed in anechoic environment in which an external noise is intercepted and a radio wave does not reflect internally. An anechoic chamber (room version of a shield box) is proper facilities but needs a wide space and a huge cost. Especially, the equipment under wireless system test on the production line can not radiate any signal radio wave outside before approval. The shield box satisfies these conditions.
-
Product
Large-size Hybrid Reverberation / Anechoic Chamber
F-Series
-
The F large-size hybrid Reverberation/Anechoic Chamber represents the most versatile OTA test system in the market today. With the same unique test features of their E Series RC counterparts, the F-Series can also test large form-factor devices under test (DUTs) like laptops, large TV sets, solar and trash compactors, drones, fridges or washing and vending machines, among others.
-
Product
Environment Meters
-
Lutron Electronic Enterprise Co., Ltd.
Highly precise, compact, and pocket-sized environment meters designed for HVAC, industrial, agriculture, and field applications.
-
Product
Solar Spectrum Test Chamber / Solar Radiation Test Chamber
-
WEIBER Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. Weiber provide Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Weiber provide Solar Simulation Test Chamber.
-
Product
Expendable Refrigerant Chambers
LDF Series
-
The Bemco LDF Series of wide range expendable refrigerant chambers are designed for low initial cost, rapid temperature cycling, environmental stress screening (ESS), and for handling large thermal loads. These systems are compact for their size, can be bench mounted, and are easily modified to special testing configurations.
-
Product
Explosion-Proof Chamber
-
NEWARE offers powerful enviromental test chambers to provide comprehensive testing support for your battery testing.
-
Product
Benchtop Chambers
-
A compact, portable environmental simulation unit designed to fit on laboratory benchtops for testing small products, components, or materials.
-
Product
Anechoic Chambers
-
Eckel Noise Control Technologies
Anechoic Chambers are echo-free enclosures with a sound energy absorption level of 99% to 100%, or a reflected sound pressure level of 10% or less. The frequency at which the energy absorption drops below 99%, or the pressure reflection exceeds 10%, is known as the low-frequency cut-off. Sound absorption is obtained by lining the walls, ceilings, and floor with wedges or other sound absorbing elements or SuperSoft panels, depending on performance level required and cut-off desired.
-
Product
Antenna Test Chambers
-
Special design for low PIM antenna measurements Shielding > 90 dB Frequency Range 700/1000 MHz to 6000 MHz Residual PIM < -165 dBc (@ 2 x 43 dBm) Up to 6 antenna ports for multi-band and MIMO antennas Standard models for antennas up to 2.7 m length Customized solutions available on request
-
Product
Vehicle Test Chambers
-
Our dynamometer chambers feature dependable mechanical refrigeration, superior air flow, and expansive control systems. Our dynamometer drive-in vehicle test chambers are designed to integrate directly with a dynamometer system, while simultaneously exposing vehicles to a wide variety of environmental conditions including temperature and/or humidity, rain, wind, and more. Our control systems allow for precise temperature and humidity testing while meeting your exact specifications.
-
Product
Ozone Test Chamber
EKT-2001OZ-HCLSX
-
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
Product
High & Low Temperature Chamber
-
NEWARE offers powerful enviromental test chambers to provide comprehensive testing support for your battery testing.
-
Product
Rain Test Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Rain test chambers for ingress protection testing simulates rain/water test as per IEC 60529 and DIN 40050-9((IP Code standard)) test standard. • IPX1 Protection against vertically dripping water• IPX2 Dripping water ± 15° from vertical• IPX3 Protection against spraying water• IPX4 Protection against splashing water• IPX5 Protection against low pressure jetting water• IPX6 Protection against high pressure jetting water• IPX7 Protection against temporary immersion• IPX8 Protection against continuous immersion• IPX9K Extremely high pressure jetting water
-
Product
Thermal Vacuum Chamber
-
Telstar Vacuum Solutions offers innovative custom solutions in design, construction and installation of space simulation thermal vacuum chambers, specially developed to optimize testing efficiency.
-
Product
Ozone Aging Test Chamber
-
This product series are mainly used to evaluate the ozone aging resisting performance of rubber and the protective efficacy of the antiozonant so as to take the effective ozone-aging resisting measures to extend the life span of the rubber products.
-
Product
Ambient Pressure Photoemission Spectroscopy With Nitrogen Environment
-
The APS04-N2-RH incorporates a tuneable deep ultra-violet (UV) source outputting 3.4 - 7.0 eV, for absolute work function and highest occupied molecular orbital (HOMO) measurements, a surface photovoltage spectroscopy (SPS) module outputting 400 - 1000 nm for Voc and Eg measurements, together with a 50 x 50 mm scanning area for planar relative work function measurements (Fermi level).
-
Product
Reverberation Chambers
-
Over the past several decades, RCs have been enjoying growing popularity as a promising facility for the characterization of wireless devices and for EMC testing. The RC (Reverberation Chamber) measurement method exhibits much competitive superiority over the AC (Anechoic Chamber) method and TEM Cell method, such as low cost, enhanced test repeatability, a more realistic test environment, and easily achieved high-field environment. The application of the RC for performing EMC testing was first proposed by H. A. Mendes in 1968. In the recent IEC 61000-4-21 standard, the importance of EMC testing using RCs as an alternative measurement technique has been recognized.
-
Product
Salt Spray Test Chamber
-
Salt water spraying/corrosive resistant machine are specialized to test the performance of the products for its surfaces of various materials after treatment of corrosive protection by means of painting, coating, galvanizing, anodizing and of lubricant.
-
Product
Walk-In Solar Panel Test Chamber
-
For testing various size Walk in Solar Panel Test Chamber WIEBER designs and manufactures Walk in Solar Photovoltaic Testing Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes.
-
Product
Environmental Test Chambers
-
An enclosure used to test the effects of specified environmental conditions on biological items, industrial products, materials, and electronic devices and components.
-
Product
2 Zone Thermal Shock Test Chamber
-
2-Zone Thermal Shock Testing Equipment with programmable electronics.
