Electrical Testers
-
Product
SpaceWire RMAP Tester
121
-
The SpaceWire RMAP Tester is a software test platform that provides the means to validate SpaceWire RMAP target implementations and to test the generic functionality of any unit that relies on the RMAP protocol for its configuration and control.
-
Product
Carbon Monoxide Detector Tester
Solo C3
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
Saicheng Friction Peel Tester
-
X-810 Friction Peel Tester measures static and dynamic coefficient of friction, as well as run seal strength tests, 180° peel test, 90° peel test.
-
Product
Megohmmeters/Insulation Resistance Testers
-
Full line of megohmmeters with test voltages 50V to 5000V. Capability to measure insulation resistance up to 10T. These rugged, weather resistant meters are accurate, reliable and built to perform. Battery, AC Powered & Hand-cranked models available.
-
Product
DIN Abrasion Tester
UI-FT24
-
DIN Abrasion Tester – DIN Abrader(Abraser) is a Rotary Drum Abrasion Tester of rubber testing instruments to test abrasion resistance of rubber, shoe sole. DIN abrasion test method meets ISO 4649, DIN 53516, ASTM D5963, SATRA TM174, and other abrasion resistance test method.
-
Product
Electric Power System Characteristics Test
-
This test is also known as the power supply line voltage and frequency variations test. A few of the measured characteristics are: voltage and frequency modulation, voltage spike, and voltage transient recovery.
-
Product
Portable Electrical Management Systems
EMS-LCHW30
-
Progressive Industries Portable Electrical Management Systems (EMS) provide full RV protection against all adverse power conditions. You will feel secure with multi-mode surge, voltage, polarity and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: Voltage(s), current, frequency, error code, and previous error code (if applicable). Replacement parts are simply plug-and-play, making repairs quick and easy. As with our portable models, the computer is driven by state of the art microprocessors. Should the software ever change, EMS owners can receive a free upgrade at no cost.
-
Product
CANbus Network Tester
-
Automatic Pin Test - automatically checks any abnormality on the OBD2 port caused by shorting (i.e., Pin 16 Power shorted to Ground), reverse polarity, and any other abnormalities
-
Product
Electric Vehicle Charger Testing
EV-TEST100
-
EV-TEST100 in combination with appropriate HT multifunction instrument simulates an electric vehicle connected to the charging station, allowing you to verify the EVSE full functionality and electrical safety. EV-TEST100 is able to test charging stations with charging modes 2 and 3 and Type 2 connector (European standard).
-
Product
Shoe Heat Insulation Tester
UI-FT08
-
Shoe Heat Insulation Tester – Thermal Insulation Tester is used to test shoe heat insulation / thermal insulation against hot performance. Place the shoe in sandbath and the footwear shall contact with the plate(forepart and the heel) in certain temperature for a given period. Then to measure the temperature increase inside of the shoe. The contact temperature and time is specified in production standard.
-
Product
Defibrillator Analyzers, Pacemaker Testers and AED Testers
-
Fluke Biomedical’s defibrillator analyzers and defibrillator/transcutaneous pacemaker testing devices are rugged, portable precision test instruments that ensure proper operation and ultimate performance of critical life-support cardiac-resuscitation equipment. We offer best-in-class defibrillator testers that feature capabilities which encompass a wide spectrum of worldwide established pulse shapes, showcasing AED tester compatibility, and outperforming competitors in accuracy and standards.
-
Product
ATX Power Supply Tester
Dr.Power II
-
Thermaltake Technology Co., Ltd.
Designed from the ground-up, it supports every ATX power supply available today up to ATX12V v2.3.- Oversized LCD panel that accurately shows the value of each specific power rails (within one-tenth of a volt).- Accurate voltage indicating for +12V/+5V/+3.3V/5VSB/-12V.- Built-in output connectors diagnostic system, low-voltage, high-voltage, no voltage, PG alarm systems.
-
-
Product
Single-Functional Testers
MI 3121
-
The MI 3121 SMARTEC Insulation / Continuity is a tester for dead testing of electrical installations. With both an analogue and digital representation of the results, the instrument ensures accurate measurements up to 2000 Ω on continuity and up to 30 GΩ on insulation function. Configurable limits enable a PASS / FAIL evaluation of test results, which is accompanied with the bright red and green indicator lights for comfortable use even in the dark conditions. The MI 3121 is equipped with a built-in charger and has a magnetic holder in order to free up hands for testing.
-
Product
Electrical Heat Shrink Tubing Solutions
-
TE Connectivity produces Raychem Electrical heat shrink tubing that sets extremely high standards in areas such as insulation, protection, and element proofing. Raychem shrink tubing uses a duplication process that involves a cross-linked material design ensuring cable system's performance. This cross-linked design creates an impenetrable barrier from the elements while simultaneously binding cables and insulating them. The heat shrink process involves tubing that utilizes a thermal influence that causes it to tightly shrink and adhere to a cable. This tight seal is not only ultra-protective, but also flexible, abrasion resistant, and easy to use. This flexible tubing can fit a huge range of cable sizes and specifications. Perfect for various different operations and industrial applications. This includes cables, wires, and even joints.
-
Product
Earth Tester
TAURUS PRECIOHM ET
-
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
Product
Digital Vibration Tester
DVM-1000
-
Quick accurate analysis for checking balance and alignment of a rotating object. Large LCD display Statistics: Mean, Max, MIN, No. of Measurements and Std deviation Inch/Metric Conversion with the push of a button Max Hold Function Regulated Output(AC output 2.0v peak full scale
-
Product
Load Cell Tester
LCT-Ultimate
-
Industrial Measurement Systems Ltd.
This most advanced Load Cell Tester model LCT-Ultimate is a stand-alone hand-held device that was especially designed for full trouble shooting of strain-gage based load cells. The LCT-Ultimate can check all common types of standard load cells that are available on the market:
-
Product
Digital Igniter Tester
Alpha 4314
-
The Alpha 4314 Digital Igniter Tester is a portable digital ohmmeter which has been specifically designed for ultra-safe resistance testing on explosive devices (i.e. squibs, detonators).
-
Product
Mobilize Electrical Safety Analyzer And Tester
Safe-T Sim®
-
The world’s smallest automated electrical safety analyzer is designed to perform all electrical safety tests with the touch of one button. Advanced features and half the cost of other automated safety analyzers. User-defined tests with programmable Pass and Fail limits. Wireless technology plus our app provide the capability to control the Safe-T Sim and generate a complete electronic test report right from your smart device!*
-
Product
Electrical Calibration
GF6018A
-
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
Product
Anaerobic Jar Tester
LD-LAJ-A12
-
Anaerobic JarLD-LAJ-A12with 3.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
-
Product
Loudspeaker Cable Testers
EMO E450
-
The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.
-
Product
AATCC Wrinkle Recovery Tester
M272
-
To determine a fabric's ability to recover after wrinkling under a predetermined load for a set period of time. Set of 3-D plastic replicas are available to grade fabrics.
-
Product
Bit Error Rate Tester
iBERT Series
-
Provide a range of signal conditioning and BER analysis from 1.5 Gb/s to 40 Gb/s on 1-4 channels and deliver the test and measurement industry''s broadest serial communications test portfolio of bit error rate tester products.
-
Product
Electrical Design Software
AutoCAD Electrical
-
AutoCAD Electrical software includes all the functionality of familiar AutoCAD software, plus a complete set of electrical design CAD features.
-
Product
Wi-Fi / Bluetooth / GPS Tester
MP5010
-
*Wi-Fi/Bluetooth/GPS Mobile Phone Tablet Integration Tester
-
Product
HIPOT testers
HypotMAX III
-
Patented SmartGFI® functionStorage of 50 test setupsRemote Safety InterlockUSB/RS-232 or GPIB interfaces availableAdvanced menu driven controlDigitally controlled arc detection systemCHARGE LO® & RAMP HI® systems
-
Product
Transformer Turns Ratio Testers
-
Transformer turns ratio testers from TRT series are DV Power instruments mainly designed for the measurement of power transformer turns ratio. Also, they measure transformer excitation current and phase shift. Special tests, such as automatic vector group detection and magnetic balance, can be performed on three-phase transformers and three-phase autotransformers.All models, except TRT03 series, have a built-in true three-phase power source, which is necessary for testing turns ratio of transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.DV Power turns ratio testers can output various test voltages for different applications. From the extremely low test voltage of 1 V AC that enables turns ratio verification of the majority of current transformers, up to the highest test voltage of 500 V AC that provides the most accurate turns ratio testing of power transformers used in power generation and transmission. By using the external booster, test voltage increases up to 5 kV AC in order to successfully test capacitive voltage transformers.All DV Power turns ratio testers have a built-in tap changer control unit. Because of that, it is possible to control the on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, the instrument and included DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option significantly facilitates and shortens the turns ratio testing time.TRT turns ratio testers use the same set of cables as three-phase winding ohmmeter & tap changer analyzers from the TWA series. Consequently, it enables one-time cable setup for performing eight tests:turns ratioexcitation currentphase anglemagnetic balancevector group detectionwinding resistanceon-load tap changer DVtestand demagnetization.
-
Product
Corrosion (Salt Spray Tester)
-
This device is used to test the surface treatment of various materials.
