Fiber Test Systems
-
Product
EBIRST 50-pin D-type To 2x8-pin Power D-type Adapter
93-005-236
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
-
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
-
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
EBIRST 200-pin LFH To 96-pin SCSI Adapter Cable
93-002-226
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, to ST
7-416804506-036
-
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, to ST.
-
Product
EBIRST 200-pin LFH To 104-pin D-type Adapter
93-002-422
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
-
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
Product
Universal OTP Functional Test System for the Production of Level and Fluid Sensors
-
Multifunctional function tester with parallel test function based on the LXinstruments OTP2 system platform. The system is used for assembly, final test and calibration of liquid and level sensors for commercial vehicles, construction machinery and shipbuilding in a high mix / medium volume environment.
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
-
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
SMD Test Fixture
16034G
-
Perform impedance evaluation on a minimum SMD size of 0.6(L) x 0.3(W) [mm]
-
Product
LitePoint RF Test System
J750
-
The option of adding LitePoint instrumentation to the J750 system delivers a cost-effective, complete production test solution covering global wireless connectivity standards.
-
Product
Parametric Test Fixture
U2941A
-
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
EFT Module for Teststand
-
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
Product
Test Fixture, Axial And Radial
16047A
-
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
TD-SCDMA Analysis Using NI PXI RF Test Instruments
NI-RFmx TD-SCDMA
-
The NI-RFmx TD-SCDMA personality is a highly optimized API for performing physical layer measurements on TD-SCDMA cellular standard signals. NI-RFmx TD-SCDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
Product
In-Circuit Test System Repairs
-
Forwessun provides expert repair services for a wide range of Test Systems, helping you maintain optimal performance and extend the life of your equipment. Our team of skilled technicians quickly identifies and addresses issues, ensuring that your system is back in operation with minimal downtime. We handle both routine and complex repairs, offering comprehensive solutions to keep your systems running efficiently and reliably.
-
Product
Audio and Acoustic Functional Test Solution
-
With the growing popularity of Internet of Things devices worldwide, many electrical products are adopting voice commands as their user interface. This means that acoustic and audio test challenges are likely to impact more products than ever before. Test teams must meet extended test coverage requirements to ensure product quality while maintaining throughput and operational efficiency. For a solution to meet these sorts of demands, it must:
-
Product
SoC Test System
T2000
-
SoC devices require small-lot high-mix manufacturing methods in the present era of rapid generation change. Semiconductor makers struggle with requirements to replace their testers on a 2-3 year cycle. The T2000 addresses their needs by enabling rapid response to market needs with minimum capital investment.
-
Product
Mezzanine System Carrier
MMS8010 / MMS8011
-
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
Product
Mezzanine System
5181
-
ECM P/N 5181 uses TI TLV320AIC23 high resolution audio codecs to provide two channels of Audio input and two channels of Audio output. Each input channel consists of two inputs a left and a right, and each output channel consists of two outputs left and right. The outputs are muteable.
-
Product
Dual 2 Channel Fibre Optic Mux SC/PC
40-815-222
-
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
Bloomy Simulation Reference System
-
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
-
Product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Flex Socket Test Module
JT 2127/Flex Socket Test Module
-
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
Product
AIM System Solutions
-
AIM can provide a wide range of customized solutions:*Special-to Type Test Equipment (STTE)*High Level Bus Analysers (HLBA)*Data Acquisition Recording & Simulation Systems*Aircraft Ground Equipment (AGE)*MIL-STD-1760 Weapon Test Sets*Fibre optic MIL-STD-1553 Stub/ARINC429 Link Extension System (FoMIS/FoL)
-
Product
Test Instruments
-
Test instrumentation from COTS to custom, including VXI, PXI and LXI-based platforms.
-
Product
Automated Compliance and Device Characterization Tests
N5990A
-
The Keysight N5990A test automation software platform is the most powerful tool for serial and multi-lane gigabit testing. It is the unique universal platform for testing a wide range of digital buses such as PCI Express, USB, HDMI or MIPI. The same graphical user interface and operating principles are used for all applications. This boosts productivity, especially when testing devices which support multiple digital buses. The N5990A can be tailored to your individual test needs with the flexible test sequenzer and controls all instruments needed for your tests. The configurable database interface of the N5990A test automation platform enables the convenient storage of all test results. A web interface allows an effective and easy operation. Custom calibration and test procedures can be implemented easily with User Programming.
-
Product
LabVIEW Professional Development System
-
ntegrate hardware from a variety of measurement instruments and devicesIntuitive graphical programming syntax to simplify automationBuild custom user interfaces for engineering applicationsBuilt-in algorithms for signal processing, analysis, math, and PID controlSoftware engineering tools to debug, validate, and deploy codeOne-year SSP membership for technical support, online training, and software upgrades
-
Product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
-
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
Product
Military Communications Test
-
Astronics testers for military radios and wireless communications systems help you keep your most critical communications up and running smoothly. Write test program sets once and deploy them instantaneously everywhere – whether your test set is in the factory, at the depot, or in operation.
