-
Product
Flame Detector
SMC 3100
-
The SMC 3100 Series Flame Detector utilizes a tri-spectra design (UV, IR and visible light spectrums) to provide continuous and reliable flame detection. The 3100 Series design provides the ability to detect flames from both hydrocarbon and non-hydrocarbon sources, making it ideal for a facility where the flame source could be generated from a variety of gases.
-
Product
Flame Photometers
-
Flame Photometer applies the emission spectrum as the basic principle, which uses the flame heat and excites part of the atoms in alkaline earth metal. The atoms receive energy and transfer it to the old energy level. When the atom is at a normal energy level it releases the energy.
-
Product
UV/IR Flame Detector
FL500
-
The FL500 UV/IR Flame Detector monitors for radiation emitted by a flame in both the ultraviolet (UV) and infrared (IR) spectral ranges. This UV/IR combination provides a fast response time and increased false alarm immunity against sources of radiation for reliable protection.
-
Product
HMV Horizontal Flame Chamber - Motor Vehicles
-
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
Product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
-
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
Product
Needle Flame Test Apparatus
-
Needle Flame Test Apparatus is designed to carry out fire hazard testing. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. Testing with regard to fire hazards can be done by creating exactly the conditions occurring in practice. However, this is not possible in most instances. Hence for this test, the actual conditions are simulated as closely as possible by the Needle Flame Test Apparatus.
-
Product
Flame Photometers
-
Flame Photometers are used widely in the measurement of alkali elements concentration in all sample types in: Mineral Extraction, Oil Industry, Paper Industry, Pharmaceuticals, Soil Analysis, Utilities, Food & Beverage, Chemical Manufacture and Fertilizer and Clinical laboratory testing and Pathological study in medical health.
-
Product
Gas and Flame Detection System
Zero Two
-
Modular system offering the widest range of control cards for use in an integrated fire and/or gas detection system. The Zero Two Series system can monitor any combination of the following: combustible gas, H2S, toxic gas, ultrasonic, oxygen deficiency and flame detection.
-
Product
HVR-LS Horizontal Vertical Flame Tester
HVR-LS/HVR-LSS
-
This equipment meets the requirements of ANSI/UL94, IEC60950-1, IEC695-2-2 and GB Standard. It is used to test the appliances and plastic materials parts of electrical equipment for the horizontal, vertical flammability test. The product tank shell is irony spray, and configured a transparent viewing window, the digital meter shows the burning time, afterflame time, afterglow time, this device has beautiful appearance, is easy to use and has reliable performance.
-
Product
IEC60695 Needle Flame Test Machine
CX-Z18
-
Shenzhen Chuangxin Instruments Co., Ltd.
Needle Flame Tester is made according to Standard IEC60695 and GB5169, meanwhile it’s a synthesis test equipment that can meet related standard requirements. It’s mainly used to simulate technical evaluation interior equipment. It’s applied to the risk of ignition test of electrotechnical equipment, parts and elements, also suitable for the risk of ignition test of solid electrical insulating materials or other combustible material.
-
Product
Needle Flame Combustion Tester
-
Shanghai Dean Electrical Co., Ltd
The touch screen control needle flame combustion tester is developed according to the requirements of the needle flame combustion test in the standard
-
Product
ZY-3 Needle Flame Test
ZY-3/ZY-3S
-
According to IEC60695-2-2 and IEC60695-11-5, ZY-3/ZY-3S Needle Flame Test is applied in the production and quality control department of lighting instrument, hyperpiesia electrical apparatus, domestic appliance, machine electric appliance, electrical machine, power tool, electronic instrument, electrician instrument and technical equipment. Also, it is fit for the industry of insulation material, engineering plastics and solid combustible material.
-
-
Product
Flame & Other Plastics Testing
-
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
Product
Flame Testing
-
Helping you ensure acceptable flammability and flame resistance for electronic products and components.
-
Product
Flame Burning Tester
DRK3024A
-
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
Product
Integral Intelligent Flame Detector
FS-100
-
FS-100 utilizes SMT technology which integrates a photoelectric sensor, a microprocessor, and a Human-Computer Interface (HCI) and an output interface together, sending out various outputs including an ON/OFF flame signal, a fault signal, a 4-20mA signal, and an RS-485 output (meets the MODBUS standard) via the quick connector.
-
Product
Gas & Flame Detection System
Syntel
-
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Heavy Impact Tester, Battery Safety Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery impact tester tests the safety of the battery through different weights, different heights and different impact areas. After a series of tests on this battery impact tester, the battery must not have flame or explosion.
-
Product
Personal Safety Gas Monitors
-
Teledyne Gas & Flame Detection
Want to protect your staff with high-end portable gas detectors? Discover Teledyne Gas and Flame Detection gas detection solutions.
-
Product
Medical Face Masks Flammability Tester
-
Sataton Instruments Technology CO., Ltd
Medical face masks flammability tester is to determine the fire resistance performance of medical face masks and full face masks. The tester can provide a specific flame and make the dummy head with facepiece move to the flame under a specific speed. The operator can observe the effects of the flame on the masks and facepiece. The tester is suitable for medical face mask, respiratory protective equipment and full face masks.
-
Product
GFID Analyzer
-
Gasmet Flame Ionization Detector (GFID) is designed for continuous total hydrocarbon (THC) measurements. GFID analyzer offers a TÜV certified solution (QAL1) for measuring pollutants from hot, wet and corrosive gas streams.
-
Product
Control Unit
MX 62 TP
-
Teledyne Gas & Flame Detection
Bringing together the latest data logger and alarm unit for gas and flame detection systems, the MX 62 TP features an innovative HMI interface specifically designed to facilitate user-controller interactions.This interaction is simplified by a large, fully interactive 10" (up to 15") high-definition colour touchscreen, allowing for clearer visualisation of critical gas detection data.
-
Product
Infrared Camera System
FlareSpection
-
The FlareSpection™ system provides extremely clear and reliable flare image and pilot flame monitoring of multiple flare tips. FlareSpection optimizes plant operations, improves safety, and ensures regulatory compliance. It enables you to remotely and automatically confirm flare operation and detect differences in flare stack heat signatures.
-
Product
Multi Channel Detectors
-
Dual, triple, quad and eight channel infrared detectors for gas analysis and flame detection sensors where more than one element or event is to be detected.
-
Product
Fire and Gas Detection System
-
An innovative, modular system that combines highly reliable programmable logic controller (PLC) technology with our advanced gas and flame field devices.
-
Product
HVUL2 Horizontal Vertical Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVUL2 Horizontal Vertical Flame Chamber is designed for the flammability testing of plastic materials used in consumer electric devices and appliances per UL94. The chamber is constructed of stainless steel with a black interior and large sliding window for easy viewing. The HVUL2 includes a fully adjustable specimen support and a precision metered gas burner. Three digital timers with remote control are mounted on the inside back wall of the chamber, allowing for precise and simplified line-of-sight operation.
-
Product
Horizontal Flammability Tester
-
Sataton Instruments Technology CO., Ltd
Horizontal flame resistance tester is design based on FMVSS 302 to determine the burning behavior of materials as interior in motor vehicles by calculating the burning rate of the specimen after ignition by a small flame. Exposed to a certain flame for specified time, the specimen which is clamped in a U shape holder will be measured for the burned distance and time taken to burn this distance. The tester is particularly important for assessing safety of the materials used in the passenger compartment.
-
Product
Platinum Wire Electrode – 0.1–1.0 Mm Diameters
PEE1
-
High-purity platinum wire (99.99%) designed for flame tests, water electrolysis, and general electrochemical research. Featuring excellent conductivity, corrosion resistance, and thermal stability, platinum wire provides a chemically inert support that does not interfere with flame colors or electrochemical reactions. Available in diameters from 0.1 mm to 1.0 mm, with custom lengths and configurations available.
