PCMCIA Interfaces
-
Product
Linear Testfixture for Pylon Mass Interconnected Cassette interface (Cassette Not Included) 6 Positions Blocks, UUT 306 x 248 mm
MG-02-01 Pylon Genrad VG series
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 6 interface blocks of 170 signals• All interface blocks can be customized
-
Product
Ethernet, GPIB And USB To Serial Interface Board
-
ICS's Model 9006 is a multi-interface to serial board that adds Ethernet, GPIB and USB interfaces to serial devices or older instruments. Use with an embedded processor board to create smart instruments with multiple interfaces. The 9006's Ethernet port is VXI-11 compatible for easy control by the following computer systems without special drivers: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. VXI-11 is one of the 9006's Ethernet protocols. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Ethernet-GPIB-USB to Modbus RTU Interface
Model 9009
-
* All interfaces provide full control of the Modbus RTU slave devices.* Ethernet port supports VXI-11, raw socket and Modbus TCP/IP to Modbus RTU conversion. * GPIB port works with any IEEE-488.2 compatible GPIB controller.* USB port uses Microsoft supplied driver to prevent operating system change problems.* The 9009 uses a simple command set that is accessible from any port.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls. Works with Agilent, NI and Kikisui VISA libraries* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Ethernet interface protocol is fully VXI-11 compliant and does not require special PC drivers.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* OEM oriented board designed for integration inside the user's system with only one cable. On board regulator works with 5 to 15 Vdc power.* Support programs Include ICS's VXI-11 and VISA keyboard control programs and a NTML page utility for uploading your customer webpages.
-
Product
Ethernet To GPIB Instrument Interfaces
-
ICS's 9055 and 8055 Ethernet to GPIB Instrument Interfaces convert any GPIB instrument into a VXI-11.3 compatible instrument that does not require special drivers and is compatible with the following operating systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows systems with VISA or an RPC library. ICS's 9055 and 8055 use VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. To learn more about the VXI-11 protocol and how it benefits your system, download our new VXI-11 Tutorial or a copy of the VXI-11 Specification.
-
Product
Analog I/O Interfaces
-
United Electronic Industries, Inc.
24 differential analog input channels Maximum sampling rate of 1000 Hz per channel 18-bit resolution ±3 µA accuracy 350 Vrms Isolation Dynamic autozero support Embedded averaging engine
-
Product
PCI 32 Channel TTL Digital Interface
8010
-
The 8010 PCI digital I/O interface provides 32 channels of buffered drive digital I/O, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
Interface Solutions (Rigid Probes) I-P1S2
1017928
-
The Interface Solutions Rigid Probes, specifically the I-P1S2 model, is engineered for precision and reliability in critical applications. This design features a basic contact probe capable of withstanding extreme temperatures ranging from -45°C to +250°C, making it ideal for environments with challenging thermal conditions. The probe's continuous current rating of 40A ensures high performance, allowing it to maintain its functionality even under rigorous electrical demands.
-
Product
Portable Interface Unit
1553-USB-PIU
-
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The unit is supplied with "C" Driver library, together with a Windows GUI, providing a user friendly software tool for all 1553 set-ups, data management and storage.
-
Product
Single Port Serial Interface
APCI-7300-3
-
*PCI interface to the 32-bit data bus. *Asynchronous communication adapter, 1-port serial interface*1 socket for SI modules*Modular structure through SI modules*Configurable as: RS232, RS422, RS485, with or without isolation, or 20 mA Current Loop (active, passive) with isolation*Addressing through software
-
Product
PCI 8 Form C Relay Output / 8 Isolated Input Digital Interface
8011
-
The 8011 digital I/O interface provides 8 optically isolated inputs and 8 Form C relay outputs. The inputs protect the PC and other sensitive equipment from spikes and ground loop current that can be generated in industrial environments, while the outputs provide higher current capabilities (up to 2A) and are optimized for 24V operation.
-
Product
Network Interface & Acceleration Cards
-
Advantech's PCIe accelerators and network interface cards bring high-speed connectivity and fast packet processing to network appliances and servers.
-
Product
DMX to Analog Interfaces
-
The MTX-DE48 decodes signals from DMX control desks to analog dimmers. It is used to integrate DMX controllers into existing analog installations. The standard 0 to 10V output is compatable with many LED drivers. Output may be adjusted up to 28V for use with some older dimmer systems. A negative output voltage option is also available.
-
Product
PCI Express to VME interface
SIS1100e/3104
-
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
-
Product
Test & Simulation Interface for PCI Express
PCIe-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI Express
-
Product
PMC Interface Module Carrier
PIM-Carrier-6U
-
The PMC Carrier routes the PMC IO from P04/P14 to J3/J5. PIM-Carrier-6U routes the IO from J3/J5 to the two PIM positions. The PIMs route the IO to the bezel providing the equivalent of PMC front bezel IO on the rear of the chassis.
-
Product
DISCRETE TMTC INTERFACE BOX
-
The Discrete TM/TC Box is a 6U custom 19’’ rack equipment that could be filled with 6U, 4HP plug-ins covering the main ECSS compliant discrete I /Fs. The I/O signals of this box are all arranged in the rear side of the box, keeping clear the front side: in this way no accidental operation could be performed on the box.
-
Product
PXI RS232 Interface Galvanic Isolation
PXI‑8432/4 - OTP2-Modul-Nr196
-
The PXI‑8432/4 module is a high-performance, dielectric-proof interface for high-speed communication with RS-232 devices. The module offers data transfers via the high-speed DMA interface, multithreading and multiprocessor support. NI serial ports appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
2U, 4U, and 6U Developmental RF Interface Units
1257A-D
Interface
The Astronics 1257A-D is a sixth-generation RFIU design. It comes with a new easy-to-use LXI Core 2011-compliant device and new enhanced features, including the ability to acquire all of the components you need to assemble your own unit in-house, reducing your design time.
-
Product
Programming Interface for CMC Test Sets
CMEngine
-
CMEngine is an open programming interface that enables you to integrate the CMC test sets into your own testing environment and control them within any type of application.
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - 6U VPX
Model 57611
-
- Four or eight channels of serial FPDP interface- Fully compliant with VITA 17.1specification- Fiber optic or copper serial interfaces- One or two Virtex-6 FPGAs- Up to 2 or 4 GB of DDR3 SDRAM- PCI Express interface up to x8- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
Product
Automatic Test Equipment, Test Interface Units and Test Program Sets
-
Axis Aerospace & Technologies Ltd.
AXISCADES is a pioneer in Test Solutions and has a long pedigree in developing Test Systems. AXISCADES has designed and developed Automatic Test Equipment, Test Interface Units/Interface Test Adapters and associated Test Program Set Software for Indian and Global, Aerospace and Defence OEMs and End Users.
-
Product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Smartcard Interfaces
-
ST offers complete analog interfaces for asynchronous 1.8 V, 3 V and 5 V smartcards. They can be placed between the card and the microcontroller with only a few external components to perform all supply protection and control functions. Main targeted applications are smartcard readers for set-top boxes, IC card readers for banking, identification and pay TV.
-
-
Product
Reference Grade Compact Audio Interface
Lyra 2
-
Lyra represents the pinnacle of compact audio interfaces. Packing Prism Sounds trusted, uncompromising AD/DA conversion into a compact chassis perfect for use in the studio or on the road.
-
Product
PCI Express 16 Reed Relay Output Digital Interface
8003e
-
The 8003e PCI Express digital I/O interface provides 16 Reed relay outputs. The outputs provide high quality, long-life, dry contact switch closures suitable for low-current applications up to 10VA. Reed relays are normally open and close when energized. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
Configurable System For Temperature Measurement With CAN Interface
MU thermocouple1 CAN
-
The thermocouple measuring unit offers connections for 8 thermocouples, which are designed for the temperature measuring ranges J, K or T, depending on the product version.
-
Product
Bench/System Linear Regulated DC Power Supply With Smart Analog Controls, Single, Dual Or Triple Outputs, 48 To 242 Watts, With/without Remote Interfaces
PL Series
-
ingle, dual or triple output modelsModels from 6V/8A up to 60V/1.5ALinear regulation - for the best performanceUltra-compact design - uses up less spaceTrue Analogue controls - for ease of useS-Lock function - instantly lock settingsV-Span function - customize the voltage rangeLow current range and current meter averagingDC output switches and "view limits" buttonSelectable remote sense terminalsIndependent, Isolated Tracking, Ratio Tracking and True Parallel modes on dual & triple modelsHigh current low voltage output on triple output model
-
Product
Shuttle Bus VMC Intelligent Interface Card
IIB-SB-VME
-
The Shuttle Bus VME is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, andMultiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a VMEplatform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include LDB_BCT,LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
