PCMCIA Interfaces
-
Product
NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
781962-01
CAN Interface
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
GPIB User Installable Interface Module
EL34GPBU
Interface Module
EL34GPBU GPIB user-installable interface (SCPI-1999, IEEE 488.2) module adds a GPIB interface to your EL30000 Series bench electronic load.
-
Product
Serial Interface Device
Serial Interface
The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Interface Card
XMC-WMUX
Interface Card
Alta Data Technologies’ XMC-WMUX interface module (PCI Express Mezzanine Card for Carriers and Single Board Computers or Carriers) is a single or dual-channel (A-B Redundant = 4 Busses per Channel/Wings) WMUX card supported by the latest software technologies.
-
Product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-01
Interface Module
2-Port, C Series Vehicle Multiprotocol Interface Module—The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
Product
Portable Avionics Interfaces for USB 3.1
UA2000
Interface
The all-new USB 3.1 design and low-power requirements mean the UA2000 is compatible with USB 2, USB 3, USB 4, and Thunderbolt™ ports. The product ships with both USB-C and USB-A cables for easy connection to current and future computer ports.
-
Product
cRIO-PN-S, Slave, C Series PROFINET Slave Interface Module
782131-01
Interface Module
Slave, C Series PROFINET Slave Interface Module - The cRIO-PN-S connects NI programmable automation controllers (PACs) to PROFINET industrial networks as powerful slaves. The interface includes the NI‑PROFINET for CompactRIO driver for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces. The cRIO-PN-S is only compatible with CompactRIO systems.
-
Product
3U CompactPCI Serial 4-Port USB 3.2/2-Port Ethernet Card
cPCI-A3USB
Ethernet Interface
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 4x USB3.2 Gen 1 ports and 2x RJ45 2.5G LAN ports in front panel- 1x USB2.0 port on board- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
Interface Module for the Multimode, Muliprotocol Excalibur 8000 Family Carrier Boards
M8K1553MCH
Interface Module
The M8K1553MCH interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M8K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M8K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
Product
Interface
RAR15XF-TB
Interface
On-board firmware, large data buffers, and a high-level API are integrated to provide total flexibility in monitoring and generating ARINC bus traffic. Simultaneous scheduled and burst mode (FIFO) messaging is supported on all ARINC 429 transmit channels. Each ARINC 429 receive channel provides simultaneous dedicated and buffered mode storage, along with label/SDI filtering.
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
Interface
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
Multichannel Interface Card
DAS-429mPCIe/RT8-717
Interface Card
The card complies with the PCI Express support one lane 2.5 Gbps PCI Express. The card’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating ARINC 429 and ARINC 717 interfaces and for performing system simulation both in the lab and in the field.
-
Product
PCIe-8244, 4-Port, USB3 Vision Frame Grabber Device
782890-01
Interface
The PCIe‑8244 is a USB 3.0 interface device designed for use with USB3 Vision cameras. USB 3.0 is ideal for high-data-rate machine vision applications. USB3 Vision cameras also offer plug‑and‑play functionality and ease of use through a standardized catalog of functions.
-
Product
Interface
RCNIC-A2PA
Interface
The RCNIC platform is a high performance PMC module for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
PCI-8432, 4-Port, PCI, Isolated, RS232 Serial Interface Device
779145-01
Interface
The PCI‑8432/4 is a high-performance interface for high-speed, port‑to‑port isolated communication with RS232 devices. The PCI‑8432/4 features high-performance DMA transfers, multithreading, and multiprocessor support. NI … serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe and PCI Avionics Interface Cards
Interface
Ballard PCI Express (PCIe) and PCI Avionics Interface Cards enable computers to interface with a variety of avionics databuses for testing, validating and simulating commercial and military avionics equipment and systems.
-
Product
Interface
3508 MMS ECM
Interface
The 3508 Electrical Conversion Module (ECM) provides six (6) RS-232 outputs and ten (10) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
20 GHz Differential Probe with ProLink Interface
DH20-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PXI-8431, 4-Port, RS485/RS422 PXI Serial Interface Module
778985-01
Serial Interface
4-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/4 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
Ethernet Interface
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
Product
PCIe to PXIe Remote Control Interface Cable, 5m
43-921-500
Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
Product
Low-profile High-Performance IEEE488 GPIB Interface for PCIe Bus
LPCIe-3488A
Interface
The IEEE-488 standard, also known as GPIB, is a bus interface that connects instruments with a computer to form an ATE system. Today, GPIB is still the most popular interface between computer and instruments. ADLINK"s USB-3488A, LPCI-3488A and LPCIe-3488A controller interface cards are fully compatible with the IEEE-488.2 instrumentation control and communication standard and are capable of controlling up to 14 stand-alone instruments via IEEE-488 cables. The USB-3488A, LPCI-3488A and LPCIe-3488A are designed to meet the requirements of high performance and maximum programming portability.
-
Product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
Interface Card
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
Product
Mini USB (90º) To 90 Series Interface
J90USBJ
Interface
Use in ITA SideTripaddle modules VPC 510104136 required
-
Product
USB-485/2, 2-Port, USB, RS485/RS422 Serial Interface Device
778476-02
Serial Interface
The USB‑485/2 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/2 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PXIe-8245, 4-Port, 10/100/1000BASE-T PXI Ethernet Interface Module
787313-01
Ethernet Interface
The PXIe-8245 supports Ethernet-based communication between PXI hardware and external instruments and devices. This PXI Ethernet Interface Module includes four RJ45 10/100/1000BASE-T Ethernet interface ports in a single-slot PXI Express module.
-
Product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
LIN Interface
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
Product
USB-8502, 1-Port, High-Speed/FD, USB CAN Interface Device
784661-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
sbRIO-9862, Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module
785963-01
CAN Interface
Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The sbRIO‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The sbRIO‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The sbRIO‑9862 is only compatible with CompactRIO systems. Non-enclosed modules are designed for OEM applications.
