Test Prods
-
Product
Temperature Cycling Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Temperature Cycling test chamber is performed on materials to determine the resistance of exposure to alternating extremes of high and low temperatures.
-
Product
PID Testing Equipment
-
The potential induced degradation (PID) is addressed with the standard IEC TS 62804-1. The standard defines two methods that enable analyzing occurring PID effects in a specific PV module type. PSE AG offers the necessary equipment for the test in a climate chamber. The test equipment can work with any climate chamber on the market and is delivered turnkey. It comes with all necessary equipment, high voltage power sources, sensors, data acquisition and software.
-
Product
Electro Fatigue Testing Machine
EPS Series
-
Jinan Testing Equipment IE Corporation
EPS series Electro Fatigue testing machine are fast acting table-top testers ideally suitable for performing static and dynamic fatigue tests on a variety of materials and components. These electro-dynamic machines use a linear electric motor with an adjustable upper cross-head of a stiff dual column frame. The electro-dynamic actuator is connected to single phase power, which resulting in a clean low maintenance solution. With dynamic force capacities, the Electro Fatigue testing machines are used to evaluate the mechanical properties of biologic materials, composites, orthopedic fixation devices, prostheses, spinal constructs, stents, dental implants, elastomeric materials and others.
-
Product
AC Resonance Test System
-
KV Hipot Power Test Equipment Co.,Ltd
KVXZ-270kVA/270kV Variable Frequency AC Resonance Test System is applied for AC dielectric test for electric equipment.
-
Product
Acceleration Testing
-
The acceleration test is performed on a centrifuge to assure that material can structurally withstand the steady state inertia loads that are induced by platform acceleration, deceleration, and maneuver in the service environment, and can function without degradation during and following exposure to these forces. Acceleration tests are also used to assure that material does not become hazardous after exposure to crash loads. The acceleration test method is applicable to material that is installed in mobile platforms such as aircraft, helicopters, aerospace vehicles, air-carried stores, ground-launched missiles, trains, ships, automotive vehicles, etc.
-
Product
Test System
2000/DATS
-
WesTest Engineering Corporation
The WesTest-2000/DATS features Teradyne's high performance Digital Test Instrument and state-of-the-art intrsuments from Agilent, Elgar and North Atlantic.
-
Product
Ball Pressure Test Device
ZBP-T
-
Made up by the related item according to IEC60695, IEC884-1, GB/T5169.21-2006, GB4706.1-2005, GB2099.1-2008, etc. • R = 2.5mm Pressure: 20N • Base with thermocouple hole • Material: 304 stainless steel
-
Product
Loss Testing
-
Count on Tempo Communications Optical Power Meters to test and maintain your fiber optic networks. Use to accurately ensure that signals are being transmitted at the correct power levels in your fiber network.
-
Product
Test System
LB303
-
Computer Gesteuerte Systeme GmbH
The test system features the durable G12 receiver from the Virginia Panel Cooperation for the adapter interface. The LB303 is equipped with a power supply of max. 6 kW and can control up to 2 load boxes (in an external rack).
-
Product
Automation Testing
-
Automated tests require a short execution time and let you avoid unwanted delays. Day or night, your automated tests will run around the clock. As a result of automation, you get a faster time to market. We automate thousands of simultaneous manual tests maximizing test coverage, and letting you lower the costs of testing in the long run.
-
Product
Pump Test System
-
This automated test system evaluates a wide range of performance metrics for a cooling pump assembly. The LabVIEW based system programs the DUT then initiates a series of tests to check:Serial communication verificationMotor voltage & currentImpeller speed and flowAir and water temperaturesLeak and level sensor functions
-
Product
Armature Testing
-
Electronic Systems of Wisconsin, Inc.
ESW Armature Test Systems are equipped with the latest features the market has to offer. The on-screen display makes it easier to read, track, and record your armature information. ESW's data collection software is compatible with almost any type of system that allows the user to store the information on any software platform. Our Testers store your data, so that you never have to worry about losing important information again. We will work with you to meet your customized testing needs. Please see the videos and slideshow below to view some of our Armature Testers.
-
Product
Chemical Emissions Testing
-
Underwriters Laboratories Inc.
As a global leader in the science of safety, UL evaluates products and materials to determine their impact on indoor air quality and, by extension, human health. Whether your products need to meet the emissions requirements of environmental certifications or regulations or you simply wish to have a better understanding of your products'''' potential impact on the indoor air for legal or risk assessment purposes, UL is your partner for developing healthier, lower emitting products.
-
Product
ESD Testing Service
-
Innovative Circuits Engineering, inc
ICE’s ESD Testing lab has state-of-the-art equipment and in–house technical expertise to perform a whole range of ESD/Latch-up and associated testing services.
-
Product
Testing of Rear Axle Steering
-
*2 high-precision servo axes for linear load simulation*Communication via CAN / Flexray*Function and noise measurements (NVH)*Supply and discharge of the test specimens via WTs on double belt conveyors*Connection to the production control
-
Product
Bed of Nails Test Clips
142-2
-
These multi-purpose test clips are a great way to tap live readings. Unique micro pins cause less damage, should you decide to pierce the wire's insulation.
-
Product
Accessories: Test Hardware
-
Copernicus Technology supply test hardware accessories to support Intermittent Fault Detection testing using VIFD™ and IFDIS™ test equipment, such as Interface Test Adapters (ITA). We also supply and repair general purpose and customer-spec test hardware accessories: ITAs, Break-Out Boxes (shown below) and Mobile Vibration Systems. The Mobile Vibration System can be quickly set up in repair bays for applying environmental stimulus to components and wiring harnesses during testing.
-
Product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
Functional Test
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
-
Product
PXI Test Instrumentation
-
The Yelo Pixi general purpose tester is a PXI based functional test system with in-circuit and continuity capability. Built into a free standing 19” rack is a PXI chassis, mass interconnect fixture interface, PC, flat screen and space for additional user selectable instrumentation.
-
Product
AC Insulation Testing
-
AC insulation tests are a popular response to the increasingly demanding industrial, power and domestic marketplaces. Insulation materials have had to become more efficient to keep up with demand; more efficient equipment requires less insulation material to meet the minimum acceptable value of insulation resistance. In turn, cables have become smaller and lighter. However, under certain higher stress testing conditions such as DC testing, cables like Crossed Linked Polyethylene (XLPE) can quickly degrade.
-
Product
Integration of Inline Test Systems
-
The test system and adapter can also be integrated in inline test systems. Additional communication can take place via interfaces (e.g. RS232, DLL). We have already created numerous integrations for different manufacturers.
-
Product
Supported Test Systems
-
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
Product
Reach-In Ageing Test Chambers
-
Aging Chamber has been designed to simulate environmental condition to test the stability and reliability of products under stressed environment. Weiber is a leading manufacturer and supplier of Aging Test Chamber in India and abroad. Weiber offers scientific equipments at the most economical rates and versatile design. Microprocessor based Aging Test Chambers are made in accordance with the international testing standards. The equipments are NABL, NSF certified and CE approved. Aging Chamber maintains 25% to 95 % RH. The Test Chamber is digitally controlled delivering accurate result under controlled environmental conditions. This chamber also known as Accelerated Ageing Test Chamber.
-
Product
Plastic Fabrications Testing Equipment
-
PD and PHD Pinhole/Holiday Detectors have an alarm circuit to alert the operator when a fault has been located and the required test voltage can be set on the unit's meter. Spark Testers provide an inexpensive means of testing but have no output voltage meter or audible alarm. However, they can test joints even if the backing is not connected.
-
Product
Test System
DA-1 ATS
-
The DA-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Capacitance And Tan Delta Test
Bushing Tap Adapter Kit
-
Bushing Tap Adapter Kit is designed to perform Capacitance and Tan Delta tests on power transformer bushings The kit can b e used with the following ISA Test Set STS 5000 TD 5000 STS 4000 TD 5000 TDX 5000.
-
Product
Ground Testing
-
Weshine Electric Manufacturing Co., Ltd
1.Soil resistivity tester supports 2, 3 and 4wire grounding resistance measurement. 2. 4digit large LCD display with white screen backlight, suitable for use in dimly lit places. 3. IP65 protection grade, good waterproof, compact and portable, supports multiple functional tests.
-
Product
Functional Test Fixtures
-
EMC Technologies designs and manufactures discretely wired and wireless functional test fixtures used for performance verification of PCBs and Electronic Assemblies. Commercial applications have included work in support of many industries including: satellite TV, computer servers, medical, networking, and telecommunication.
-
Product
MANUAL TEST FIXTURE KITS
SERIES 5590
-
Built with unique design features: Ease of assembly and disassembly All side panels are removable Side panel material is delrin for easy machining for connectors, switches etc.Light weight and durable construction2" Between Probe plate and lid plate allowing more room for tall board components
-
Product
Universal Testing Machine
-
A Universal Testing machine, also known as universal tester, materials testing machine, is used to test the tensile strength and compressive strength of materials. It is named after the fact that it can perform many standard tensile and compression tests on materials, components and structures. Along with these, there are many more capabilities of this testing machine. There are variety of terms in the industry that are used to refer to a UTM. Most common are “tensile tester”, “compression tester” and “bend tester”. An earlier name for a tensile testing machine is a Tensometer. It is used to play out the numerous tractable pressure and compressive quality of materials or parts.
