Showing results: 1186 - 1200 of 3178 items found.
-
FastX-APU -
Alacron
The FastX-APU framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX-APU, is a two thirds length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex FPGA before being sent to the PCIe (X4) Gen 2 switch to the host or the AMD APU.
-
M97 series -
Maynuo Electronic Co.,Ltd
The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications. From 150W to 200KW, there are many models to choose from :
-
M98 Series -
Maynuo Electronic Co.,Ltd
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
TAC1000 -
Rhesca Co., Ltd.
For the measurement of tackiness (instantaneous adhesive strength) of various pastes and adhesive tapes, it is possible to quantitatively evaluate the data, which until now had large errors due to individual differences. First, press the measuring probe, which is controlled (approach speed, pressure force, pressure time, separation speed) against the sample, and measure the adhesive force in the process of separating. Measured data can be processed by a computer. With double temperature control (patented), the sample piece is preheated from the back side with a hot plate and the heated probe penetrates the measurement surface, making it possible to keep the set temperature and the temperature of the test surface to be evaluated constant. Since the pressurization time can be as short as 10msec, it is possible to measure the tackiness caused by momentary contact.
-
9740-T -
Strobe Data Inc.
Triple+ speed Windows/NT Osprey Co-Processor for five times the system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes FPJ11® compatible hardware floating point. Performance equivalent 3.8 times the DCJ-11® and 130% of FPJ-11. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. Qbus®/Unibus® support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel Qbus or Unibus adapter. Operates only under Windows/NT. WNT Support license included.
-
9740-Q -
Strobe Data Inc.
Quad+ speed Windows/NT Osprey Co-Processor for five times the system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes FPJ11® compatible hardware floating point. Performance equivalent 4.5 times the DCJ-11® and 130% of FPJ-11. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. Qbus®/Unibus® support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel Qbus or Unibus adapter. Operates only under Windows/NT. WNT Support license included.
-
72-6638 -
Tenma
An instrument to accurately measure air velocity and wind speed in air conditioning and heating systems as well as for environmental monitoring.
-
10 -
Picoprobe
PICOPROBE® MODEL 10 is a multipurpose, high speed, passive probe which can be used for driving as well as receiving signals. The Model 10 consists of a one meter length of flexible 50 ohm coaxial cable terminated by a carefully trimmed SMA on one end and by a miniature, high speed 50 ohm connector, specially developed to receive Model 10 replaceable coaxial probe tips, on the other. The 50 ohm coaxial cable was custom designed for Model 10 to be high speed, yet very flexible, so that moving the cable would not disturb the probe points.
-
Amprobe TACH-20 -
Amprobe Test Tools
The Amprobe TACH20 Hand-held Tachometer accurately measures rotational or surface speed as well as length. It comes with a large LCD display that allows the user to easily read the measurement. It also has a built in memory function that permits automatic storage of maximum, minimum, average values plus the last measurement displayed.
-
Teledyne Princeton Instruments
This specifically designed fiber optic data interface kit allows the computer and the GigE® camera head to be separated by up to 550 m without the loss of data. The kit consists of two compact, high speed transceivers (interface modules) for completely transparent operation between the host computer and the camera.
-
5 Series MSO Low Profile -
Tektronix, Inc.
In applications that demand extreme channel density, the 5 Series MSO Low Profile oscilloscope sets a new standard for performance. With 12-bit analog-to-digital converters, this high speed digitizer offers 8 input channels (plus AUX Trig) in a compact package, only 3.5 inches high (2U).
-
Monarch Instrument
Monarch Instrument has been manufacturing Stroboscopes for visual inspection and speed measurement for over 35 years. We are recognized as the leading manufacturer of portable hand held stroboscopes. We have xenon flash tube and LED versions available in a variety of different models to suit your application requirements.
-
HE950 -
Electro-Sensors, Inc.
Features • Square-wave pulse frequency output, NPN open-collector • Zero speed operation with no signal loss • 5-24 VDC powered • Gap sensing capability up to 3 mm • Senses broad range of ferrous targets (pulser discs / wraps with steel slugs, keyways, bolt heads, and gear teeth)
-
Ashling Microsystems Ltd
DesignWare ARC Real-time trace allows you to use an Ashling Ultra-XD pod to capture trace from an ARC HS core and upload it to the MetaWare Debugger at gigabit Ethernet speeds. Captured trace can be turned into a “replay” database enabling you to debug your program by executing it both forwards and backwards.
-
Teledyne Princeton Instruments
This specially designed fiber optic data interface kit allows the computer and the USB 2.0 camera head to be separated by up to 500 m without the loss of data. This kit consists of two compact, high speed transceivers (interface modules) for completely transparent operation between the host computer and the camera.
