Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
Pulse Generators
-
Dedicated analogue pulse generators and function generators with true pulse capability.
-
Product
Pulsed DC Holiday Detector Inspection Kit
280
-
The Elcometer 280 Pulsed DC Holiday Detector is a ‘stick type’ holiday detector that has been designed to make pulsed DC high voltage holiday detection safer, easier and more reliable than ever before.
-
Product
Rail-to-Rail Op Amplifiers
-
Analog Devices high speed (> 50 MHz) rail-to-rail op amps enable you to operate at lower supply voltages, swing closer to the rails, and provide wider dynamic range. Featuring a portfolio with a wide variety of op amps, including both rail-to-rail input/output as well as just rail-to-rail output, ADI provides the widest portfolio of leading edge products available on the market. Whether it is wide bandwidth, high slew rate or low distortion, or rail to rail, no one sets more performance standards for next generation designs than Analog Devices.
-
Product
Microwave System Amplifier, 2 GHz to 26.5 GHZ
83018A
Amplifier
The Keysight 83018A microwave system amplifier is a compact, off-the-shelf amplifier designed for systems designers and integrators. This amplifier provides power where you need it to recover system losses and to boost available power in RF and microwave ATE systems. The ultrabroad bandwidth from 2 to 26.5 GHz allows the designer to replace several narrow bandwidth amplifiers with a single Keysight amplifier, eliminating the need for crossover networks or multiple bias supplies. The standard Keysight 83018A includes internal directional detectors for external leveling applications. With excellent noise figure relative to its broad bandwidth and high gain, this amplifier significantly improves system noise figure and dynamic range. The Keysight 83018A comes equipped with a low profile heat sink, an integral mounting bracket, and a two-meter dc power supply cable. Thermal characteristics and power supply design allow fast, easy integration into most measurement systems.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
Designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment), ITU-T K21 and ITU-T K44.
-
Product
Synchronization and Distribution Amplifier - PCIe
Model 7892
-
The Model 7892 High-Speed Synchronizer and Distribution PCIe Board synchronizes multiple Pentek Cobalt or Onyx boards within a system. It enables synchronous sampling and timing for a wide range of multichannel high-speed data acquisition, DSP, and software radio applications
-
Product
Pulsed Lasers and LEDs
-
PicoQuant's compact and reliable turn-key diode laser solutions work in picosecond pulsed, modulated, or fast-switched (nsec to µsec) operation mode. The laser systems typically consist of a common driver unit and exchangeable heads. Specialized lasers are also available as stand-alone units.
-
Product
Low-Noise Parametric Amplifiers
-
Insight Product Company offers Low-Noise Parametric Amplfiers based on Monolithic Integrated Circuits (MIC) in the frequency range of 30 to 100 GHz.
-
Product
Dynamic Power Device Analyzer/Double Pulse Tester
PD1500A
-
As an off-the-shelf measurement solution, the PD1500A delivers reliable, repeatable measurements of wide-bandgap semiconductors. The platform ensures user safety and protection of the system’s measurement hardware.
-
Product
Headphone Amplifier
MH-8
-
High-power headphone amplifier that distributes the stereo input to eight headphone outputs
-
Product
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP031
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
860MHz CATV Indoor Bi-directional Amplifier
-
Hangzhou Softel Optic Co., Ltd.
SA801H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network.
-
Product
Power Amplifiers
-
RPG Medium Power Amplifiers are developed and manufactured by using most modern discrete components and thin film technologies, in order to cover the frequency range 50 to 130 GHz. With improved DC-supply and modern semiconductors these medium power amplifiers not only deliver high power output but also superior power added efficiency (PAE) and higher linearity. These medium power amplifiers are available as a standard product and on request as a customized manufactured product..
-
Product
Low Noise Amplifier
-
Low noise amplifier with a typical small signal gain of 22 dB and a nominal noise figure of 5dB across the frequencyrange of 90 to 110 GHz.
-
-
Product
Microwave Power Amplifiers
-
Spanawave/Giga-tronics Microwave Power Amplifiers deliver outstanding performance and exceptional value. These ultra-broadband amplifiers have excellent pulse performance and modulated signal fidelity, ideal for testing in wireless communications, defense EW and radar testing and general purpose microwave laboratory applications. Have the power you need to overcome cable and switching losses, or to drive higher power mixers, detectors and very high power amplifiers.
-
Product
Pulsed And CW EPR/ESR: Synthesizers Up To 280 GHz
-
Insight Product Company offers synthesizers at frequencies from 30 to 280 GHz which can be used in EPR/ ESR experiments. These sythnesizers are designed to go swiftly from the generation to the non-generation mode and back. This process is controlled by external TTL signal. There is also the possibility to manipulate the phase, namely to shift it by 90 degrees and 180 degrees. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
110 GHz Frequency Extender, Pulsed DC Bias
N5293AX02
Frequency Extender
The N5293AX02 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 110 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
Product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
-
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
Product
150 kHz-230 MHz Broadband Power Amplifiers
-
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 822B - 824B
-
- Work as Transmitter & Fiber Amplifier- AGC - Automatic Gain Control- Built in RF Booster- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lesers with Isolaters- Variable SLOPE Control- Output Wavelength : 1310nmPower Options :- 40V DC- 12V DC / 2 Amp- STB Adapter along with PSP- 7.4V, 2600 mAH Battery
-
-
Product
Solid State Broadband High Power Amplifier 1900 - 6000 MHz / 200 Watts
2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. for EMC, RF Product Test, Communications and Electronic Warfare applications.
-
Product
Combustible Trip Amplifier Module
TA102A
-
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display).
-
Product
Low Frequency Active Antenna And Amplifier
Type NLF-2
-
A Hot, Active, Noise Reducing Antenna System that will sit on your desk and copy 2200, 1700, and 600 through 160 Meter Experimental and Amateur Radio Signals!
-
Product
Load Cell DIN Rail Signal Amplifier
LCD20
-
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Product
Overdrive Protected Amplifier
-
RF Lambda’s line of overdrive protected amplifiers incorporate a technology which eliminates the need for a limiter to protect the amplifier from damage. High input powers up to 10W can be injected in the amp without damage. Hermetically sealed options are available upon request.
-
Product
Time & Frequency Distribution Amplifiers
-
Brandywine offers a wide range of high quality, state of the art signal timing distribution amplifiers, all with very low phase noise. These precision timing signal distribution amplifiers offer a variety of time and frequency signals and interface formats including IRIG A, IRIG B, Have Quick, 1PPS, as well as low phase noise reference frequencies. All of our distribution amplifiers feature dual inputs with automatic failover and multiple independently buffered outputs.
-
Product
Video Pulse Generator
MS 1811
-
*4 Channels of Variable Pulse / Amplitude Output*Pulse Generation Delay between any Two Channels can be Programmable between 2ns to 1ms*Pulse Width can be programmed from 20ns to 268ms (Range: 60ns � 2Sec, Resolution: 2ns, Accuracy: �5ns)*Programmable Pulse PRI (Range: 0ns � 2Sec, Resolution: 10ns, Accuracy: �5ns)*Delay Amongst Channels (Range: 0 � 1.34S, Resolution: 2ns, Accuracy: �5ns)*Rise Time and Fall time is less than 5ns (Programmable Slew Rate 2ns to 10ns � Optional)*Pulse Amplitude can be Programmed between 50mV to 6V (Range: 0 � 6V, Resolution: 10mV)*Channels can be terminated with different loads (50W,75W and 90W)*Standard ISA Bus Interface*Clock (Frequency: 100MHz, Source: Internal/External)*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Broadband Amplifier
-
Toellner Electronic Instrumente GmbH
Will reproduce a wide range of signals without significant loss throughout the pass band.
