-
product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
product
Digital RCD Tester
8012 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Extra large LCD(78 × 67mm).● Very low consumption.● 50Hz and 60Hz operation.● Menu-driven.● Accurate digital readout of disconnection time.● Over temperature protection.● Over voltage protection.● Fuse protection.● Zero crossing circuitry permit testing at 0° or 180°.● Auto power off.● Auto off and off override.● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.●Frequency measurement indication.
-
product
POWER PROBE MAESTRO
PPTM01AS
*Connects with the new Power Probe Tek application for greater diagnostic functionality*The Maestro and Power Probe Tek App will be compatible to connect with a majority of diagnostic scan tools*Trace mode offers scope-like functionality*Stream and record visual traces of electrical issues found when diagnosing*DC voltmeter with the capability of applying battery supplied voltage or ground*AC voltmeter: TRMS, peak-to-peak/min/max, frequency, duty cycle*Resistance testing with a live or unloaded circuit*Fuel-injector test mode*Driver test for testing module drivers
-
product
Electric Load
PT04-250-63
For Telecom Rectifier and Power Supply testing. *0 to 63A up to 250V, power limited to 1,900 Watt *CC, CP, CR and CV as standard *63A available Load down to 5.3V
-
product
Hydrogen Fueling Stations
Powertech’s hydrogen station designs are supported by engineers from the company’s world-class high-pressure testing facilities, used to test fuel systems, high-pressure components, and fueling protocols for hydrogen systems.
-
product
MEMS Testing System
BK3010V2
The BaKo BK3010V2 is our updated MEMS Tester, based on our C-Mic tester, the best selling BK3010. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is very easy and can be done in a few minutes. In addition, the new BK3010V2 can be connected to a computer so you can keep and view compiled data and track trends in variations in your C-Mics.
-
product
Cloud Based Scalability Testing
Perform load and stress tests on your system using a scalable cloud based platform. Get results on demand and ensure that your infrastructure scales.
-
product
2-way Radio Signaling Test Software
Tone Generator
The new PC-based test software for RF communications engineers and technicians. Flexible, accurate code synthesizer for simulation and testing of 2-way radio systems, repeaters, remote control, ANI, Paging and more.No external hardware required.
-
product
Run Down Adapters
Testing power torque tools is essential for product quality and regulatory compliance. A run down adapter is designed is to simulate the fastening process of a screw. Mountz run down adapters improve testing repeatability by adjusting for the impact force and irregular peaks of power tools. Mounted in-line between the tool's driver and transducer, a run down adapter provides consistent and reliable torque readings.
-
product
Customer Specific Tests
No matter whether you have developed a product without an underlying standard or extended a product beyond the standard – we verify your product to see if it conforms to the characteristics specified by you. We advise you on worst-case scenarios.You need a test under certain temperature conditions? We have the possibility to execute appropriate temperature tests.You have other testing needs? Please contact us so we can consult you thereto and submit an offer.
-
product
Testing And Calibration Services
Radian Research provides a broad range of unrivaled value-added servicesincluding calibration services done by laboratory and on-site, utilitymanagement training, product training and more.
-
product
Whiteness Meter
Guangzhou Amittari Instruments Co.Ltd
AMITTARI l Whiteness Meter is mainly used to directly measure the whiteness value of object or powder with flat surface. It can be widely used in whiteness measurement of textile printing and dyeing, paint, chemical building materials, paper board, plastic products, white cement, ceramics, enamel, talc powder, starch, flour, salt, detergent, cosmetics and other substances. The instrument pass strict inspection and testing, conforms to the JJG 512-2002 Whiteness Meter Verification Regulation. Also conforms to GB3978、GB3979、GB7973、GB7974、ISO2470、GB8904.2、QB1840、GB2913、GB13025.2、GB1543、ISO2471、GB10339、GB5950、GB12911、GB2409 and other standards.
-
product
Universal Testing Machines
Infinity Machine International Inc.
Universal Testers by Infinity Machine International Inc.
-
product
Test Signal Generators
MicroImage Video Systems has a broad array of video test signal and color bar?generators designed for many applications from laboratory and testing to embedded systems. MicroImage Video Systems can design a video test signal generator for your applications. In fact, we have designed many more custom test signal generators that we offer as standard products. Small size is important and our video test signal generators start at just 1.5 inches square.
-
product
Magnetic Flux Leakage Testing
PRÜFTECHNIK Condition Monitoring GmbH
NOVAFLUX - Flux Leakage Inspection for Black or Bright Steel Bars
-
product
Polydisperse Generators
This type of generator is typically capable of spraying aqueous solutions (e.g. salt), suspensions (e.g. PSL, nanoparticles), or oil or alike substances. They serve a variety of applications from laboratory research field tests of detectors, and filter testing.
-
product
NTSC/PAL Color Bar Generator
CBG360
The CBG360 is designed to provide an accurate and affordable signal source for system testing. It also provides the necessary components for aligning color monitors to the proper brightness, color and hue.
-
product
Endurance testing machine for bed
This device is an endurance tester for ordinary home beds. It can also be used as a compression tester.
-
product
Oscilloscope - 350 MHz, 4 Analog Channels
DSOX4034A
350 MHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
product
Test & Test Development for Circuit Card Assembly
Teledyne Advanced Electronic Solutions performs comprehensive testing at the CCA and system level assembly. Teledyne AES can perform testing developed by the customer or develop a complete test strategy for the customer’s products.- Bed of Nails FixtureIn-Circuit Test (Bed of Nails) or Flying Probe Testing for rapid feedback on CCAs- Functional testing of CCAs or complete systems- Environmental testing to include vibration, thermal cycling, HASS, etc.- CCA and system level test development- High frequency testing – currently to 40 GHz- High power system testing – currently to 4kW
-
product
Performance Testing
All of Xena’s products can be used for performance testing. This typically includes measuring:*the volume of data successfully delivered between two points, usually measured in bits or packets per second*how long it takes data packets to travel between two points in a network or a device, also known as latency*variations in latency – also known as jitter – due to network congestion or other factors*how many data packets fail to reach their destination*if data packets are delivered in a different order from that in which they were sent
-
product
Low PIM Coaxial Switch, DC to 4 GHz, SP4T
87104P
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104P is a low PIM SP4T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
PXI-6733, 16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
778512-01
16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6733 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response tests (including acoustic distortion testing) and simulation (such as three-phase power simulation). In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PX...show more -
product
Graphical Waveform Editor and Instrument
PI-PAT
Much more than just a visualization tool, PI-PAT is a full-fledged graphical waveform editor that allows you to spend more time testing and less time programming. PI-PAT doesn't require any programming experience or complicated syntax. Just draw or type patterns directly into the pattern window. Move a clock edge by dragging it. Adjust integration times by entering a single number. Change the output to your DUT by clicking the Update button. You'll never have to wrangle DSP or FPGA code with PI-PAT.
-
product
2 Ch Linear Vibration Motor Tester
BK2120C
the BK2120C runs up to 4 vibration sweeps, which you define, to check whether your linear vibration motor is within the limits you set. And now you can set up your own feedback so it's even easier to determine the class of pass or the reason for failure. You still get fast, high quality testing for your linear vibration motors on the product line. And it's still versitile enough to be used for QA or QC as well.
-
product
Wafer/Dicing Frame Prober
WDF 12DP+
The WDF 12DP is a prober/handler capable of transporting and testing standard 300-mm wafers and dicing frames without need of a changeover kit. To support multiple tests after dicing, it has a special positioning function that differs from former types, as well as image-processing functions such as wafer level packaging.
-
product
Thermal Testing And Analysis
Response Dynamics Vibration Engineering, Inc.
We have consulted on thermal issues ranging from conduction issues in TECs, thermal radiation modeling, and countless air cooled system issues relating to system performance, vibration, and acoustics noise. We use a wide array of thermocouple instrumentation, thermal imaging, flow measurements, as well as finite element analysis and analytic modeling to measure, design, and debug thermal and related issues. We often work on customer products in our Response Dynamics lab where we characterize the system, engineer solution options, and prototype solutions. We then work with the customer to work the winning solution into their quality control and manufacturing process.
-
product
AC Line Splitter
1937
Peaceful Thriving Enterprise Co Ltd
The AC line splitter is a helpful testing device for electrician. Electrician can measure the current with clamp meter through the X1 and X10 measuring rings. X1 is 1:1 measurement, and X10 is ten times (1:10) of the actual current, which is helpful for small current measurement. This device also combines the function of socket tester and GFCI tester, which means electrician can use this tester to test socket and load at the same time.
-
product
Plug Socet & Cord Testing
Educated Design & Development, Inc.
Flexing Tests: On flexible cables (or cords sets with fitted plugs), electric tools or hand lamps. Meets requirements of standards such as IEC 60335, IEC 60227, IEC 60745 and UL745. This product is for continuous bending tests of cables or cord sets fitted with plugs. The model F39 allows the simultaneous testing of two samples in it's standard version. This not only allows for substantial time savings, but also allows for the testing current circuits to be simplified by looping through the cables.
-
product
UV Energy Meters
Shenzhen Linshang Technology Co., Ltd.
As an UV integrator supplier providing a fair price of UV energy meter for LED, mercury vapor lamp, curing and UV exposure machine, Linshang has developed four different models of UV energy meters. According to the type of ultraviolet light source measured, the instruments can be divided into two categories, LS120, LS130 and LS132 for testing the energy and intensity of high-pressure mercury lamps, LS128, LS131 and LS133 for testing UV LED.