Showing results: 6046 - 6060 of 8449 items found.
-
IT6800A/B Series -
I-TECH Electronic Co., Ltd
IT6800 single channel programmable DC power supply (180W-216W) with resolution 1mV/0.1mA, users can adjust the voltage/current stepping by pressing the left and right keys to moving the cursor and programs by the front panel. OVP/OTP protection. IT6800 supports timer function and their built-in RS232 and USB communication interfaces offer you a convinience testing experience.
-
Labodam
Labodam portable dissolved oxygen meters are equipped with polarographic sensors to measure dissolved oxygen content. The manual salinity & barometric pressure compensation helps in accurate measurement of dissolved oxygen. Due to the portable nature of these instruments they can be used for various applications such as at water purification plants and waste water management plants for testing & quality analysis.
-
NEGATIVE FILM -
Tester Soft Ltd.
Negative film and photomask inspection originated from the extensive use of printed circuit boards. Negative films and photomasks are used in large quantities. The early detection method is to use the "inspection light table" for inspection, which requires too much manpower and material resources, and manual testing may be due to eye fatigue and negligence.
-
Applied Systems Engineering, Inc
ASE provides a total solution approach to the area of protocol test equipment with its’ family of PC based protocol test products. The ASE2000 RTU Test Set is a full-featured protocol test unit that provides the user with a powerful and flexible tool for testing and maintaining SCADA RTU and SCADA IED equipment and diagnosing communication problems.
-
Tessent® -
Mentor Graphics Corp.
The Tessent product suite combines features of deterministic scan testing, embedded pattern compression, built-in self-test, specialized embedded memory test and repair, and boundary scan, as well as board and system-level test technologies. This comprehensive silicon test and yield analysis solution is built on the foundation of the best-in-class solutions for each test discipline
-
WT2080 -
Lisun Electronics Inc.
WT2080 LED Power Driver Test Instrument is the comprehensive test instrument for LED drive power which is according to GB/T 24825-2009 and IEC 62384:2006. It can measure the following parameters: Input Characteristics Test (AC&DC), Output Characteristics Test (AC&DC), Output Start Characteristics Test (DC) and Harmonic Testing.
-
MicroContact AG
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
DiagnoSYS Systems Ltd
The PinPoint Alpha system is a flexible, adaptable and modular PCB and IC fault finding system, which allows you to apply different electronic test methods to obtain maximum test coverage and fault detection. Test signals can be applied at the PCB edge connector or through test clips and DTIs to perform fixtureless in-circuit testing.
-
Green Hill Software, Inc.
Static analyzers attempt to find code sequences that may result in buffer overflows, resource leaks, or many other security and reliability problems. Source code analyzers are effective at locating a significant class of defects that are not detected by compilers during standard builds and often go undetected during run-time testing or typical field operation.
-
SAS -
AMETEK Programmable Power, Inc.
A spacecraft solar array is subjected to large temperature excursions, varying insolation (the amount of sunlight falling on the array), mechanical changes and aging, which substantially effect both its short and long term performance. In order to test the spacecraft's power environment, a cost-effective solution for ground based testing is to utilize a solar array simulator.
-
Reltech Limited
The selection of the test socket is critical to the performance of a device during qualification testing where electrical bias and signals are applied. Key factors such as mechanical compatibility, operating temperature, ability to withstand high moisture levels, signal speed and lead inductance/capacitance all need to be taken into account when selecting the best socket for the test application.
-
LMK Position -
TechnoTeam Bildverarbeitung GmbH
The LMK Position is a photometric robotic system combining LMK-based machine vision with the high precision and flexible movements of a 6-axis Denso VS industrial robot and, optionally, a JETI specbos spectroradiometer. It allows effective and cost-efficient accompanying measurements during research and development tasks and rapid small-series product testing of all kinds of display systems.
-
AEMC Instruments
Full line of power and power quality analyzers, loggers and meters including for extending measurement ranges. The wide range of applications include electrical monitoring, harmonic detection & analysis, utility testing, energy management, power factor analysis and correction, power demand and consumption, kW measurement, industrial power systems, and commercial maintenance.
-
KT-45 -
KILTER ELECTRONIC CO.,LTD
Quickly test twisted cable RJ45 and BNC connector including T568A/B, 10-Base-T (UTP/STP), Token Ring, etc. Automatic test for open circuits, shorts, reversals, miswires, continuity. Main unit and one remote allow one person to test. Includes protective leather pouch. Testing before and after installation
-
SECULIFE UL Series -
GMC-I Messtechnik GmbH
The SECULIFE UL Series is specifically designed to test the electrical safety of all types of diagnostic ultrasound transducers, totally independent of the ultrasound machines on which they are typically used. Although the SECULIFE UL can be used on virtually any type of ultrasound transducer, it is especially recommended in the testing of TEE (Transesophageal Echocardiography) transducers prior to each use.