-
product
PXI-7842, Virtex-5 LX50 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module
780338-01
Virtex-5 LX50 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7842 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. T...show more -
product
Battery Voltage Recorder
BVR Series
Battery voltage recorders from BVR series are designed to serve as a support tool for cell voltage measurement during battery capacity testing.During capacity testing, cell voltage, temperature, inter-cell connection voltage, and specific gravity should be measured in order to determine failling cells in the string that should be replaced.Furthermore, IEEE standards for stationary batteries applications stipulate periodical measurement of overall string voltage, as well as cell voltage and tempe...show more -
product
Fully Automatic No Load ( Routine) Testing Panel For Self Priming Motors
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 11.4MΩ
50-298-053
The 50-298-053 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Aeronautical Ground Data Unit
GDU
Square Peg Communications Inc.
Square Peg Communications Inc.’s Aeronautical Ground Data Unit (GDU) is a software application that runs on the generic Physical Layer Tester (PLT) platform. The GDU supports the testing of physical layer performance and protocol operation for Ground Earth Stations (GESs) and Aeronautical Earth Stations (AESs) implementing Inmarsat Aero services.
-
product
Website Testing
QACraft takes pride in being one of the trusted providers for website testing services in the USA, India, and Worldwide. We have several clients across the world by testing their website and checking a number of parameters that determine the performance and user experience of the site. Our team of experts help in going through all the vital factors and prepare a detailed report. The team lists down all the key parameters, the performance of your app in all such fields, and errors if found any. O...show more -
product
Copper-DSL
Tempo Communications has long established itself as one of the premium suppliers to technicians focu... sed on DSL testing and installation. Our expertise in all aspects of copper line testing has enabled Tier #1 communication companies around the world to install, turn-up and maintain with confidence and in a timely manner. Tempo’s flagship product in this category, the SideKick®, is the go-to solution for deploying and maintaining DSL networks. Support your customers DSL broadband internet service and ensure reliable connectivity today with Tempo.Show less
-
product
Conventional Power Supply Design with Simple Analog Controls
VLF Series
VLF hipots perform voltage withstand tests and provide the voltage source for diagnostic cable testing. There is no better method for verifying the AC integrity of a cable than applying VLF AC voltage. Tan delta and partial discharge measurement accessories are frequently purchased along with VLF equipment to extend their capabilities.
-
product
Sensor for High-End Applications
ARAMIS SRX
The new ARAMIS SRX is a 3D measurement system for dynamic evaluation of 3D coordinates, 3D displacement and surface strain. It comprises the latest camera technology including 12-megapixel cameras. Capturing up to 2000 images per second, the sensor is especially designed for rapid testing applications. It comes with an additional setup for crash applications providing an image acquisition rate of 1000 images per second in HD format. With the combination of high resolution and high speed, the ARA...show more -
product
High Throughput Test Platform for Multi-Site & Index Parallel Applications
ETS-88
The ETS-88 is an optimal test platform for testing a wide variety of devices including: simple analog, high precision, high voltage, high current / power, automotive, video, audio, complex mixed-signal, as well as emerging power processes like SiC and GaN.
-
product
Terminal Mechanical Strength Test
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wir...show more -
product
Customized Testing
Independent Testing Laboratories
ITL specializes in providing custom testing. Let us help you with designing your next R&D project.
-
product
PXI 8-slot BRIC Power Multiplexer, 3-Channel, 16-Pole (3 Sub-cards)
40-571A-201
The 40-571A-201 is a 3-channel, 16-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
-
product
Sand & Dust Testing
Products with moving parts, electromechanical components, filtering systems and electronics are all susceptible to fine and large particle dust that can contaminate a product. These contaminates can cause premature failures and loss of function.Today’s test plans for phones, computers, vehicles, enclosures and aircraft include sand and dust testing to determine if this stress source would cause functional deterioration.Our services include military and automotive dust testing for both blowing and agitated dust and sand.
-
product
Imperial Test Executive
ITE
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
product
Pre-Amplifiers
MPR, MDA series
MPR, MDR series provides low noise, high gain and wideband to improve dynamic range for emission testing. We also offer customized model for variable requirments.. Example 30M-1000MHz with band-pass filter Amprifier unit for connecting antenna directly
-
product
HPx-310 Radar Signal Output Card
The HPx-310 Radar Signal Output card is a replacement for the HPx-300, form, fit, and function. It generates representative radar signals for system testing, simulation, training or radar video streaming. Under software control, the card generates radar video, trigger and azimuth signals similar to those generated by real radars.
-
product
Quasar Smart Relay Tester
The Quasar is the most advanced three-phase relay test set designed for the testing of secondary and IEC-61850 protections of any type with special focus on industrial and routine maintenance applications.
-
product
Automotive Solutions
One of the most challenging applications in the field of automotive testing is manufacturing electronics. With each successive model year, the number of automated features increases. Every segment of the automotive electronics plays a role in the safety and reliability. These critical applications require high dependability and low maintenance and warranty costs. Our customers don’t have room for error, hardware test systems must perform as designed. Circuit Check provides Automated Test Systems that meet the stringent needs of this marketplace.
-
product
Leeb Hardness Tester
Shenzhen Linshang Technology Co., Ltd.
Based on the principle of Leeb hardness measurement, the Leeb Hardness Tester, otherwise called as Leeb Rebound Hardness Tester, is considered as one of the most commonly used tools to test the hardness of the metal. It is a type of non-destructive testing tool used to inspect large sized workpieces weighing above 5 kg. Besides the hardness, it also measures the strength of materials.
-
product
Software
Tinius Olsen provides software to meet your R&D and quality control needs, working simply, efficiently and accurately. Horizon makes all your testing as effortless as it should be. It carries out your testing and seamlessly integrates with your processes. VSS works with Horizon to control your video extensometer testing.
-
product
POLARIZATION CAMERAS
Conventional high-speed cameras have been utilized for nearly eighty years and are widely accepted worldwide through continuous technological development to visualize fast occurring phenomena. In recent years, demand for using polarization in structural dynamics and high-speed object detection has been increased due to the advancement of robotics, clear film production and new materials testing technologies. On the other hand, traditional high-speed cameras lack any polarization sensitivity.
-
product
Indoor Air Quality Meter CO, CO2, Temp, RH%
AQM4
UEi Test & Measurement Instruments
Four measurements in one instrument; carbon monoxide (CO), carbon dioxide (CO2), temperature and relative humidity. Use calculated 8 hour Time Weighted Average (TWA) and 15 minute short term exposure limits of CO2 for compliance testing and CO measurements for safety testing. Record, recall or download all readings to personal computer for later analysis or record keeping.
-
product
SMT Surface Mount MEMS High-G Shock Accelerometers
Piezoresistive MEMS high-amplitude shock accelerometers represent state-of-the-art industry technology for miniature, high amplitude, DC response acceleration sensors. This series is capable of measuring long duration transient motion as well as responding to and surviving extremely fast rise times, typical of a high-g shock event as found in explosive, gun and impact testing. Both packaged and OEM configurations are offered, to fulfill a variety of installation requirements.
-
product
PCI Express 4.0 Protocol Analyzer Exerciser
Summit T416
The Summit™ T416 analyzer is the computer industry's first high speed PCIe 4.0 protocol analyzer that meets the challenge of 16GT/s and up to x16 lane width protocol analysis. Many PCIe 4.0 product designs are already in progress using the PCIe 4.0 specification. Companies are currently working with the Teledyne LeCroy Summit Z416 protocol exerciser for PCIe 4.0 at the deployment of PCIe 4.0 for host system emulation with their testing needs. This combination of a protocol analyzer and exerciser...show more -
product
Testing Hardtop Convertible
Magtrol designed this Custom Motor Test System for the testing of motors used in hydraulic systems in hardtop convertible roof drives.
-
product
Factory Testing
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Efficient factory testing is vital in order to achieve the tightest tolerances, maximum repeatability, high precisi- on and quality in the manufacturing processes, as well as long production machine lifecycles. What‘s more, it helps to reduce manufacturing costs due to minimized replacements, retesting processes, and recalibrations. Online CatalogApplication Notes
-
product
Emergency Conditions Testing
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Ultrasound Measurements
Is sound waves with frequencies higher than the upper audible limit of human hearing. Ultrasound is no different from 'normal' (audible) sound in its physical properties, except in that humans cannot hear it. Ultrasound devices operate with frequencies from 20 kHz up to several gigahertz.Ultrasonic devices are used to detect objects and measure distances. Ultrasound imaging or sonography is often used in medicine. In the nondestructive testing of products and structures, ultrasound is used to detect invisible flaws.
