-
product
Plastics Testing Solutions
AMETEK Sensors, Test & Calibration
One of the crucial factors when developing a new plastic product is testing. Only by testing the raw materials, components and finished product in accordance to the relevant standards within plastics testing, are you assured that your plastic product lives up to the high expectations on the market and that it is strong and flexible enough to do the job that it is designed for.
-
product
Insulation Testers
Rishabh Instruments Pvt. Ltd.,
Rishabh Insulation Tester is a Digital Insulation Tester with selectable test voltage up to 10kV and Insulation. Resistance measurement upto 20 TΩ. Ideal for testing insulation in live switchyards.
-
product
Switch Modules - 32 Single Pole Relays Arranged as a 16x2 Matrix
JX32/AB-1
This module has 32 single pole relays arranged as a 16x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 16x2's per chassis, or jumpered to the backplane to form up to a 256x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
product
Contact Resistance Meter
CRM 100B+
SCOPE introduces its next generation of hugely popular CRM series contact resistance meter, CRM100B+ in all new super light avatar, based on cutting edge ultra capacitor technology. CRM incorporates some state of the art hardware & smart software features making it a must have tool for testing & maintenance engineers.
-
product
Gas Filled Hv Test Transformer
YDQW-50KVA/250KV
Wuhan Sangao Electrical Test Installations Limit Co.
SF6 gas -filled testing transformers are especially designed for GIS in the factory and on-site test, and for testing all GIS switchgears and GIS components such as insulators, insulating tension pole, GIS voltage transformer and so on, the PD test can be performed under the general environment because of the merits of encapsulation, the PD level of our equipment can be lee than 3pC, and it can be added a HV bushing to perform the withstand voltage test at the same time.Small and compact dimensi...show more -
product
Optical Fiber Identifier
BD-IF400D
Shanghai Baudcom Communication Device Co.,Ltd.
BD-IF400DOptical Fiber Identifier is an important tool for optical maintenance, which isused for nondestructive fiber identification project. Meanwhile it also hasVisual Fault Locator module with fault location function. Useingthe macro bending technology on line for nondestructive testing, BD-IF400DOptical Fiber Identifier can measure the signal direction and power and avoidmisoperation resulting in interrupted lines.
-
product
Network Stability Testing
Slow-loading websites, a video call that freezes, or constant interruptions when listening to Spotify: we will all agree that network stability is just as important as bandwidth or speeds. The secret to keeping the network up and running at all times, without delays? Stability monitoring and testing, under reproducible, realistic circumstances.
-
product
High Frequency LCR Meters Up To 30MHz
Chroma 11050
Chroma Systems Solutions, Inc.
Measurement capabilities cover the primary and secondary parameters required for testing the inductance, capacitance, resistance, quality factor and loss factor of passive components
-
product
Dual RF Shielded Test Enclosure
JRE 0814-2R
Containing all the capability of the larger JRE enclosures, the rack mounted 0814-2R is ideal for testing devices with a tall form factor. Two independent 0814 series enclosures are mounted in one 19 inch rack. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
product
Antennas for EMC testing
The Laplace antennas cover 3 main groups...*Conventional log periodic types for OATS applications.*Miniature antennas for chamber and small enclosure applications.*Large loop antenna for EN55015 compliance testing.
-
product
Multifunctional testers
MI 3155 EurotestXD
MI 3155 EurotestXD is the newest flagship of Metrel’s most advanced line of multi-functional measuring instruments and is designed specifically for testing in industry. What differentiates this instrument from the rest is its ergonomic design and an intuitive user interface, encompassing a memory organizer and fully programmable AUTO SEQUENCEs, managed through a large colour touch screen display.
-
product
Advanced Matrix Scanne
System 8 (AMS)
The SYSTEM 8 Advanced Matrix Scanner is the latest addition to the SYSTEM 8 range and offers new and unique features for the testing and diagnostics of components under power-off conditions.
-
product
Averaging Clip-on Extensometer
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
product
ECM PCB Tester
MS 1105
*Used for testing of DAWN RWR PCBs in Jaguar Aircraft*19” Rack mountable with built-in wide range of IO signals *Used in 4th line servicing of PCBs*Used in LRU and system level testing*Detects 100% fault coverage including track faults*Adaptability with off-the-shelf instruments
-
product
Multi-Wavelength Meter
86122C
With an absolute wavelength accuracy of 0.2 ppm and 0.15 ppm differential accuracy, the new Keysight 86122C Multi-Wavelength Meter belongs in the top class of wavelength meters available for optical communication testing. Its wavelength range of 1270 to 1650 nm covers all fiber-to-the-home, metro and long-haul transmission systems. The instrument can measure the spectra of up to 1,000 laser lines at once, which is more than sufficient for fully populated dense-wavelength-division multiplexed systems (DWDM).
-
product
Walk-in Environmental Chambers
EWS-SERIES
Mono-block/Pre-fabricated design EWS-Series Walk-in Environmental Chambers with custom-built features to meet testing needs of large-sized test specimens
-
product
PXI High Density MUX BRIC, 20-Chan, 40-Pole
40-570-215
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow tes...show more -
product
Testing and Validation Services
With our testing and validation services, we help our clients test their products and materials to ensure compliance with the relevant standards and deliver comprehensive reporting on the results.
-
product
Low PIM Coaxial Switch, DC to 4 GHz, SP6T
87106P
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106P is a low PIM SP6T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Rotor Testing
Rotor testing equipment is capable of testing cast rotors of a range of sized and variety of designs. It is operator friendly and easy to maintain. It has data acquisition system that operates through software on PC. It offers high level analysis of individual measurement. Also allows maintaining records & generating reports with ease and flexibility.
-
product
Diode Tester
FEC VF40CM
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
product
Bluetooth LE Exerciser
testHarmony
Pre-compliance, debugging, regression and robustness testing for chipset vendors and product manufacturers in any stage of the manufacturing process – from development to post release.
-
product
Radar Altimieter Test Panel for ALT-50/55
TA-55
Radar altimeter panel designed after the ALT-50A test fixture. (Ref. Fig. 5-1). Panel allows testing of the indicator or R/T independently or together. An internal power supply is provided to support stand alone testing of the indicator. This panel contains a 4 digit DVM and comes with enclosure. This panel will allow by the book testing.
-
product
Testing of Power Steering Motors
Endurance test bench on which up to five drives can be tested at the same time. The drives / DUTs are electrically connected to resistors and driven by a servo drive according to a predefined driving profile. This exam can take up to several days. It detects currents, speeds and temperatures.
-
product
Coating & Material Thickness Gauges
GAOTek’s coating thickness gauges are designed for measuring the thickness of a material and are for sale to the United States, Canada and globally. Our products utilize non-destructive testing techniques that do not permanently affect the material they are testing. They are reliable, high quality, and affordable pieces of equipment that can provide an accurate measurement and offering an efficient and quick means of inspection or testing. Our products emphasize compactness and portability to allow the user to work in complex conditions.
-
product
Pocket Vibration Meters
DVM-0500/0600
Phase II now brings the latest state-of-the-art pocket vibration meters into our ever expanding product line of testing instrumentation.The DVM-0500/600 pocket vibration meters utilize the singular velocity parameter, making testing easy. A full frequency range is available for broad detection abilities.
-
product
ECU Simulator
PT-LabCar
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
product
ATE Test & Engineering Services
We can provide a limited scope project or a full turn key solution where we analyze a data sheet and provide a full test plan. Our wide range of ATE test equipment and experienced team can support first silicon debug to release to high volume production for a wide range of products, from Digital to RF, including wafer sort and packaged part testing. Test platforms include Verigy, Teradyne, Advantest.
-
product
COAX & LAN Cable Mapper PRO
PK-801 Multiple 10-Way PRO
The multiple 10-way PRO combines the functions of a 10-way COAX cable mapper and LAN cables identifier that enables identification of a group of improperly labeled patch cables quickly and effortlessly. It also built-in 2 selectable Net/Tel tones for tracing active Ethernet cables even when connected at a switch or Router and locating live phone line systems. This unit also with the capability to do cable/wires loopback and remote continuity testing and voltage detection and warning on F connect...show more -
product
TestPort Line Of Hand-Held Ethernet Test Equipment
The TestPort line of handheld Ethernet protocol test tools represents the state-of-the-art test equipment for telecom backhaul networks. It’s protocol support includes Gigabit Ethernet (GbE), Sychronous Ethernet (SyncE), and E1. Testing applications include protocols analysis, traffic generation, and impairment testing.
