Insulation Resistance Tester

Electrical Safety Tester

Basic testing methods of Glow wire device> and UL 746A, IEC829, DIN695, VDE0471, the Glow wire tester ZRS-3H/ZRS-3HS is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances. Adopting high-temperature coating spraying on steel structure and imported instrument display, with easy operation, stable performance the equipment is applicable to flame resistance tests of all levels of QC departments and corresponding enterprises.

Product Home Contact/Sales Company Catalog Share Add To List

Car Accessories Material Burning Tester

ZRS-4H - Lisun Electronics Inc.

• Test Gas Source: Gas or Liquefied Petroleum Gas (Suggestion: Use good quality gas if possible) • Burner inner diameter: ￠9.5±0.5mm, about 100mm long with air adjusting hole • Height of flame: Can be adjusted from 20 mm to 100 mm according to the standard requirement • Applying time of flame: Burning time can be adjusted from 0 to 99 minutes 99 seconds • Test process: Automatic control • Inner volume: 0.05m³ • Material: Stainless steel or iron plate spray • Power: AC 220V; 50Hz/5A

Product Home Contact/Sales Company Catalog Share Add To List

ZY-3 Needle Flame Test

ZY-3/ZY-3S - Lisun Electronics Inc.

According to IEC60695-2-2 and IEC60695-11-5, ZY-3/ZY-3S Needle Flame Test is applied in the production and quality control department of lighting instrument, hyperpiesia electrical apparatus, domestic appliance, machine electric appliance, electrical machine, power tool, electronic instrument, electrician instrument and technical equipment. Also, it is fit for the industry of insulation material, engineering plastics and solid combustible material.

Product Home Contact/Sales Video Company Catalog Share Add To List

TTC-1 Tracking Test Chamber

TTC-1 - Lisun Electronics Inc.

It is according to IEC60695 and IEC60112 (GB4207), the Tracking Test Chamber TTC-1 is intended for determining the degree of protection against formation of conducting paths in solid insulating materials, due to the electric stress and electrolytic contamination of the surface. This method simulates tracking currents on insulation material by providing drops between electrodes. During the process of normal use, insulating material may be exposed to moisture and dirt, if conductive, may cause stress and fire hazard.

Product Home Contact/Sales Company Catalog Share Add To List

HVR-LS Horizontal Vertical Flame Tester

HVR-LS/HVR-LSS - Lisun Electronics Inc.

This equipment meets the requirements of ANSI/UL94, IEC60950-1, IEC695-2-2 and GB Standard. It is used to test the appliances and plastic materials parts of electrical equipment for the horizontal, vertical flammability test. The product tank shell is irony spray, and configured a transparent viewing window, the digital meter shows the burning time, afterflame time, afterglow time, this device has beautiful appearance, is easy to use and has reliable performance.

Product Home Contact/Sales Company Catalog Share Add To List

HCAI-1 High Current Arc Ignition Tester

HCAI-1 - Lisun Electronics Inc.

The HCAI-1 High Current Arc Ignition Tester is according to IEC 60950-1:2001, BS EN 60950-1:2001, BS 7002:2000, GB 4943.1-2011and UL746A, IEC60947.1: 1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-2008 and other standards required simulated safety test project. Parts and components of insulating materials or other solid combustible materials that are prone to flame spread in electrical and electronic equipment may ignite due to proximity or contact with electric arc, causing electrical fire and endangering the reliable operation of equipment and personal safety.

Product Home Contact/Sales Company Catalog Share Add To List

Lamp Cap Temperature Rise Test System

TMP-L - Lisun Electronics Inc.

TMP-L is according to IEC60360-1998 and GB2512-2001 (Standard method of measurement of lamp cap temperature rise). It is used to test the working and environmental temperature as well as temperature-rise of the burner and lamp. It meets the requirement of IEC and GB Standards.

Product Home Contact/Sales Company Catalog Share Add To List

Thermally Protected Ballast Heating Test Chamber

TPB-UL935 - Lisun Electronics Inc.

Working room dimension: 610×610×610mm• Temperature range: RT+10℃～+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)

Product Home Contact/Sales Company Catalog Share Add To List

Automatic Safety Test System

LS9955/56 - Lisun Electronics Inc.

The LS9955/LS9956 Automatic Safety Test System is according to GB4706.1, IEC/EN60335-1, UL60335, GB7000, IEC60598, GB4943, IEC60950 and GB9706.1. It used for luminaries, home application and motor tools safety test in production line or Lab R&D.

Product Home Contact/Sales Video Company Catalog Share Add To List

Programmable Withstanding Voltage & Insulation Test

LS9923 - Lisun Electronics Inc.

LS9923 programmable withstanding voltage & insulation test system is high-performance testing device special for AC&DC Withstanding Voltage and Insulation Resistance Test, It allows setting the output voltage. The warning value,testing time and some other parameters can be set in the screen.It with a variety of automatic test functions. The testing is quick and high accuracy which is not only applied in the production line but also in the develop research.

Product Home Contact/Sales Video Company Catalog Share Add To List

AC/DC Withstand Voltage Test

WB2671A/WB2671B - Lisun Electronics Inc.

• Output voltage: 0-5kV (AC/DC); • Cutoff current range: AC 0~20mA (WB2671A)/0~100mA (WB2671B); DC 0-20mA; • Test time: 1-60s; • Transformer capacity: 750VA.

Product Home Contact/Sales Video Company Catalog Share Add To List

Digital Oscilloscope

JC2202TA - Lisun Electronics Inc.

The JC Series Digital Oscilloscope was designed and produced by high accuracy electronic components and modules. The test accuracy is world high class. It is used in all kinds of electronic products testing.

Product Home Contact/Sales Company Catalog Share Add To List

Ball Pressure Test Device

ZBP-T - Lisun Electronics Inc.

Made up by the related item according to IEC60695, IEC884-1, GB/T5169.21-2006, GB4706.1-2005, GB2099.1-2008, etc. • R = 2.5mm Pressure: 20N • Base with thermocouple hole • Material: 304 stainless steel

Product Home Contact/Sales Company Catalog Share Add To List

Standard Test Finger

SMT-1 - Lisun Electronics Inc.

It with Protection against electric shock device. It according to IEC60335, IEC60884, IEC61032, IEC60529, IEC60065, IEC60035, IEC60950, EN60529, EN60950, GB4706, GB7000, GB9706, UL507, VDE0470, etc.

Product Home Contact/Sales Company Catalog Share Add To List

Insulation Resistance Tester

Topics