-
product
Hardness Testers
The hardness tester products you will find at PCE Instruments (PCE) are used for determining surface hardness. Each hardness tester uses a standard method of measurement. The measuring principles of most hardness tester devices are based on either the penetration of a diamond indentor into the material being tested or a calculation related to the force of the rebound after striking the tested material. However, material hardness can also be measured accurately through ultrasonic testing. Each hardness testing method has its benefits and will allow for the precise measurement of material hardness in accordance with the technical specifications of the hardness testing instrument.
-
product
Distribution Transformer Test System
DTTS Series
Shanghai Jiuzhi Electric Co., Ltd.
The DTTS Series Distribution Transformer Test System are self-contained test sets incorporating all features necessary for testing single and three phase distribution transformer.
-
product
Preamplifiers
Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification.
-
product
Prestressed Concrete Strand Testing
ToronTech manufactures and services a wide range of advanced prestressed concrete strand testing machines and accessories.
-
product
DDR5 Logic Analyzer
FS2601
The FS2601 is one of our newest and fastest logic analyzer probes used to test DDR5 memory. It is designed to work exclusively with 4 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR5 UDIMMs running above 4000MT/s.
-
product
Electronic Product Testers
Infinity Machine International Inc.
Electronic Product Testers by Infinity Machine International Inc. - for applications such as connectors insert and extract testing machine, touch screen torsion, abrupt pull tester for power wire and headphone cable, double station electronic product cable tester, cord flexing rotary bending fatigue tester, button click electronic product tester simulation, and more.
-
product
PCIe Smart Bus Extenders
PCIeEXT-16HOT - PCIe LIVE INSERTION EXTENDER
The PCIeEXT16HOT enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system. Enabling rapid production testing and engineering debug, the hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCIe bus extender in the industry.
-
product
Energy Efficiency Testing
Underwriters Laboratories Inc.
Our testing and certification services help you to incorporate energy efficiency into product design to meet consumer demands and regulatory requirements. As a full-service Energy Star® partner, we can combine Energy Star evaluations with a range of other energy efficiency services to test and certify your products to a wide range of local, national and international standards. Once your product is certified, we add your product to our online, searchable database, and you can use the Energy Efficiency Certification Mark on your marketing materials, packaging and the product itself.
-
product
Power Amplifiers
RF Range
The RF power amplifier range from Laplace is specifically designed for EMC Immunity testing. These are compact units with characteristics matched to the requirements of IEC standards.
-
product
FCC Part 15 Testing & Certification
FCC Part 15 is the section of Title 47 of the Code of Federal Regulations that sets limitations on the amount of electromagnetic interference allowed from digital and electronic devices. FCC Part 15 also covers technical specifications, administrative requirements and other conditions relating to the marketing of FCC Part 15 devices.
-
product
High-Voltage Test Device
PGK 70 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testin...show more -
product
Meter Test Benches
Test Station
The meter test station allows simultaneous testing of 3, 5, 10 or 20 induction or static electricity meters. The test station could be constructed for single-phase electricity meters or for three-phase meters.
-
product
Acoustic Emission Testing Equipment
1283 USB AE Node
The 1283 USB AE Node is a full-featured, low-cost Acoustic Emission testing equipment that plugs conveniently into and is powered by the USB port of a user’s PC or laptop to maximize portability and versatility.
-
product
Erichsen Cupping Testing Machine
GBW Series
Jinan Testing Equipment IE Corporation
GBW series Erichsen Cupping Testing Machine is designed on the basis of screw universal material testing machine. The Erichsen Cupping Tester is suitable for cupping test of metal sheet and strip steel rolled stock etc to evaluate the plastic deformation performance and ductility. The cupping test for metal sheet thickness range is 0.1mm to 5mm, Max. punching capacity is 300KN, and the pre-tightening device is optional either with hydraulic servo loading pump or manual loading pump.
-
product
High Force DMA
DMA+ Series
*The new DMA+ series instruments are dynamic testing machines based on a innovative concept of one-piece high rigidity test frame.*They are dedicated to the accurate analysis of the viscoelastic properties of most advanced materials.
-
product
Bending Stiffness Test Fixture
Q-Card’s bending stiffness fixture features splayed feet and aggressive no-slip rubber pads for stability. It is manufactured of aerospace-grade aluminum alloy with a hard anodized, scratch-resistant, durable finish to provide years of rigorous testing and trouble-free service.
-
product
CableEye Cable Testing
A industry-grade, Windows PC driven cable tester with incredible performance yet amazingly simple to operate. CableEye cable testing has found itself in areas as diverse as working in oil/gas mining through avionics and F1 car testing to audio cables at concerts.
-
product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT MXP
SCOT MXP measures, displays and prints CLOSE, OPEN and CLOSE-OPEN time in various configurations. The MXP has a special mode to measure Pre-Insertion Resistor (PIR) closing time
-
product
PhyView Analyzer
PVA-3000
Connects up to 24 10/100/1000Base-T ports and provides access to the PHY Performance Test Suite supporting one-click, fully automated transmitter, receiver, and, auto-neg testing.
-
product
PCI Precision Resistor Card 4-Channel, 2Ω To 26.7kΩ
50-297-132
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Performance And Quality Testing
Underwriters Laboratories Inc.
Our endless pursuit of the truth helps you provide trustworthy answers to questions about products, processes, facilities and systems. Our testing, certification and verification services—and the UL Mark—provides regulators, purchasers and consumers with the information they rely on to confidently make the decisions that impact your business. Our quality assurance checks help to ensure that components and products meet your—and your stakeholders’—demands.
-
product
Coaxial Switch, DC to 18 GHz, SPDT, 24 to 30 V Solenoids
8761B
The Keysight 8761B is a single-pole, double-throw coaxial switch with excellent electrical and mechanical characteristics for 50 ohm transmission systems operating from dc to 18 GHz. It features broadband operation, long life, low SWR, excellent repeatability, and magnetic latching solenoids. The Keysight 8761B switch is small and lightweight, making it ideal for applications where space is limited. Because of its versatility and excellent electrical performance, it is well suited for automated testing and systems applications.
-
product
POWERSTROKE FUEL INJECTOR TEST KIT
DFST20
*Tests Powerstroke engines from 1994 to current*Includes adapters necessary to pressure test the fuel system*Adapters can be used for testing at both the fuel filter and at the fuel pump
-
product
Torque Measurement System
Torque measurement system is intended for periodical control and endurance testing of various moving structural elements, e.g. turbine blades, etc.
-
product
Regenerative Grid Simulator
Chroma 61800
Chroma Systems Solutions, Inc.
Full 4 quadrant, fully regenerative, AC power supply designed for common electrical product testing such as home appliances and industrial electronics that require a programmable input source
-
product
Advanced Test Module
SYSTEM 8 (ATM)
The Advanced Test Module (ATM) is a solution designed for the test and diagnostics of all logic PCB assemblies, from single component testing in-circuit up to complete assembly functional checks.
-
product
Ultrasonic Wafer Scanner
AutoWafer
Installed in more wafer applications than all other automatic ultrasonic testing tools combined, AutoWafer provides a complete, production-ready wafer scanner for wafers from 100mm to 200mm, including multiple sizes in a single batch.
-
product
Ultrasonic Flaw Detector
MFD350B
Based on ultrasonic principle, digital ultrasonic flaw detector MFD350B with 320*240 TFT LCD, it can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. It can be used in Laboratory as well as in engineering filed. With range of 0-6000mm, it can meet the requirement for general defect inspection in manufacturing industry, metallurgical industry, metal processing industry, chemical industry and so ...show more -
product
Press Down Rods Bed of Nails Testers
Protector Press Rods Family
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. ...show more -
product
Rail Traction Inverter Test System
The rail inverter test system uses a pulse test methodology to verify proper operation of the IGBT switching elements in a subway car motor control. The system is designed to verify proper commutation of the switching elements. A large capacitor bank allows testing at DC voltages up to 1kV and peak currents of up to 3kA into reactive loads.The system also integrates self test capabilities and safe-to-turn-on (STTO) diagnostics to ensure no gross faults are present prior to the application of high voltages. Further the system includes dielectric withstand (hi-pot) test capability to ensure electrical safety.