Mains
chief conduit of electricity, gas or water distribution.
-
product
Time Domain Reflectometer
IRG 2000
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR IRG 2000. The IRG 2000 impulse reflection measurement unit or time domain reflectometer is a handy, easy to carry device for single-phase cable fault pre-location. It is used in combination with a surge voltage generator on low-, medium- and high-voltage cables 0 - 65 km in length. It can also be used on live cables carrying voltage up to 400 V.* Easy and quick cable fault location* Light, compact and manageable* Main unit for the tried-and-tested pre-location method* Ideal for integration in measurement systems
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
Programmable AC Power Source
LSP-500VAC
• Applied with the AC-DC-AC inverter technology and digital waveform synthesis & waveform feedback technology, low distortion power; • Applied with entire cycle high-precision measurement technology and high-speed sampling technologies, panel of instrument will directly and accurately displays the power output of the voltage, frequency, current, active power and power factor to achieve the integration of the source table; • Applied with SCM control and measurement technology, high intelligence; • Applied with zero output impedance technology, the output equivalent impedance is almost zero and further improve the stability of power supply; • Applied with isolated floating output technology, the power output and input have good isolation, floating output, conducive to make sure power itself safety and operator’s safety; • Perfect voltage, current anomalies and overheating protection, improve the reliability of power supply; • Applied with power limiting technology to avoid strong interference on the power grid and other electrical equipment, while facilitating reliable operation of the power supply itself; • The input voltage can be option via a toggle switch of panel mains 110V/220V; • The initial phase and end phase of the output voltage waveform can be set {0°-359° (±1°)}; • Measurement process can be programmed to control (1 to 50 memory groups, 1 to 9 steps for each memory group);
-
product
Digital Multifunction
Contrel Elettronica s.r.l. Company
The DIN rail and front panel multimeters are ideal for installation in secondary distribution panels. Measurement of the main electrical parameters. Measurement of active, reactive and apparent energy. Modbus RTU, Modbus TCP, Profibus, M-Bus protocol. Digital outputs programmable as alarms or pulses.
-
product
Inspection System for high-power precise 3D X-ray CT
X-eye PCT225
Inspection System for 3D X-ray CT able to analyze defected area precisely by precise movement of axis with high polished Anti-vibration table. High-power X-ray Tube of max. 450kV and large area Flat Panel Detector of max.16 inches can be installed depending on the sample. Customized 3D CT equipment is available with selecting main parts by customers depends on their needs for size and material.
-
product
Data Collection Systems
Data collection is an increasingly important part of manufacturing, and one of the main drivers in the movement toward electronic measuring tools with output. At the top of the Starrett line, DataSure Wireless Data Collection is a state-of-the-art system for real-time collection and recording of measurement data. transmission. From measurement to input, it reduces steps, saves time and can totally eliminate error in the data collection process. Starrett also offers several newer technology products for wire-based data collection; SmartCable for single tools and the 4-Port Gage Multiplexer.
-
product
Vehicle Inspect Lines Software System
Foshan Analytical Instrument Co, Ltd.
Flexible control mode(A collective-type control mode can be adopted,but a distributive-type control can also be adopted); Powerful system function(Distributive-type control and collective-type management,provide the functions of equipment debugging,vehicle log-in,vehicle testing and bill printing.A secret code and right-limit can be set so that the system safety function is enhanced); Remote control(A remote log-in,main remote control and remote printing can be realized in accordance with the actual conditions of the testing station.At the sametime,provides a powerful data-base and one station with multi-wire:That is one testing station has more
-
product
Building Vibration Software Module
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Measurement and evaluation of vibrations in buildings to DIN 4150-3 for the determination of their effects on structures*Convenient user guidance requires only short training*Comparison with limiting values to DIN 4150-3*Simple generation of reports*Detection of the main frequency*Recording of vibration events and real-time signals*External Messengers*Offline measurement*Available as kit: VM-STRUC Kit with accelerometer KS823B
-
product
LCD Cable Testers
Shenzhen Noyafa Electronic CO.,LTD
The main function of NOYAFA LCD Cable Tester is to measure the cable length and check cable errors, by using LCD display can clearly shows the test results to users, making the faulty points visable, so that to save users time and effort.
-
product
SOI Bonding Systems
An accurate wafer bonding process is the key factor in obtaining high quality single crystalline silicon films on insulating substrates. The EVG850 SOI/Direct Wafer Bonding systems are designed to fulfill a wide range of fusion/molecular wafer bonding applications, with main focus on SOI substrates manufacturing. Ultra clean handling of wafers throughout the bonding process assures high-yield and void-free bonds. All essential steps, from cleaning and alignment to pre-bonding and IR-inspection are combined in one high volume production system. EVG850 is the only production bonding system built to operate in high throughput, high-yield environments and guarantees void-free SOI wafers up to 300 mm.The EVG300 series single wafer cleaning systems are designed for efficient removal of particles. In semiconductor processing, efficient cleaning and particles removal prior to critical process steps enables maximum yield. Wafer Bonding is a process which is strongly affected by particles: each particle on the wafer surface produces a void orders of magnitude larger than its diameter, contributing to a dramatic yield loss.
-
product
PANTESTER Multi Cable Tester
PK-7890/7890PL
PANTESTER is an advanced multifunction pin-by-pin cable tester to verify cable integrity of Datacom. Telecom and Coaxial cables and displays the test results on the main unit.
-
product
Discrete Detectors
TRAL test station is a quasi-universal test station designed to measure parameters of discrete (or small linear array) infrared detectors sensitive in a wide spectral range from about 700nm to about 16 000 nm (NIR/SWIR/MWIR/ LWIR detectors or broadband non selective detectors). All main types of infrared detectors can be tested: photonic detectors: photovoltaic/photoreconductive, cooled/non-coooled, thermal detectors, pyroelectric detectors etc.
-
product
MCB Tripping Current Characteristic Test Bench
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
product
Handyscope TP450-250XM-W5
TP450-250XM-W5
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
product
Counterfeit IC Detector
Sentry
The ABI SENTRY is a unique solution for the quick and easy detection of Counterfeit ICs and components. ABI Electronics has over 27 years of experience in the field of Test & Measurement equipment as well as Contract Electronics Manufacturing. Knowledge of both industries has allowed ABI to design this product around two main concepts:
-
product
Leak Detection System
Leak detection system (LDS) is a state-of-the-art software and hardware suite intended for leak detection in long-distance and oil products pipelines, calculation of leak location and evaluation of its intensity in constant full-time mode. The system allows to detect leaks in stationary and non-stationary pumping modes without gravity mains as well as in suspended pumping mode.
-
product
Die-cast Rotor Tester
AIP868X series
Qingdao AIP Intelligent Instruments Co., Ltd
Introducing the international testing technology and developing special sensor according to digital signal processing method, the die-cast rotor tester able to automatically analyze and judge the filling quality of die-cast rotor.This system is applied to all kinds of cast aluminum and copper rotors, such as: cast aluminum rotor of compressor motor, cast aluminum rotor of washing machine motor, cast aluminum rotor of fan motor, cast aluminum rotor of pump motor, rotor of automobile motor and three-phase asynchronous motor, etc. The main detection functions are: broken bar, fullness of the bar (thin bar, hole, bubble and porosity ), leakage between the squirrel cage and lamination, squirrel cage eccentricity, slot deviation.Test items: broken bar, thin bar, maximum amplitude value, minimum amplitude value, comprehensive value.
-
product
Ultra-Compact Immunity Tester
AXOS8
The AXOS8 is an ultra-compact immunity tester that performs all the most commonly used transient immunity tests, including Surge, EFT, Dips/Interrupts and AC/Surge Magnetic Field. The simplified user interface provides quick selection of tests and test levels, and even lets you change test parameters “on the fly” while running a test.The actual EUT power mains voltage and current are indicated in the display. Using the Electronic-Fuse function, the user can set an upper limit for EUT power mains current. This feature is useful to protect the EUT from unnecessary damage.Whether you test to the IEC 61000 series “CE Mark” standards, the IEC 60601 Medical Device standards, or any number of telecom and product specific standards, the AXOS8 tester is your one stop test station for everything from precompliance to full compliance to product development testing.A wide range of cost-efficient Coupling / Decoupling Networks for symmetrical and asymmetrical data- and signal-lines is available as an option.
-
product
Digital Circuit Breaker Analyzer
CT-7000 S3
The CT-7000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-7000 S3 is available with 3 (part number 9021-UC) or 6 contact timing channels (part number 9100-UC). The CT-7000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Both contact and motion analysis can be performed on all circuit breaker operations (OPEN, CLOSE, OPEN-CLOSE, CLOSE-OPEN, and OPEN CLOSE-OPEN). The CT-7000 S3’s timing window is selectable between 1 second, 10 seconds, and 20 seconds.
-
-
product
Dual Measurement Bench Multimeter
1908 Series
The battery operation can give more than 35 hours of operation. As well as adding portability to the unit the battery option provides isolation from the mains to aid low level measurement integrity. The USB interface is fully accessible in battery mode, allowing full data logging when used with a laptop pc. The dual measurement display shows the main and secondary reading simultaneously to provide either two parameters of the same signal (eg AC and DC Volts), two different signals (e.g AC Volts and DC current), the result and calculated function (eg value and % deviation), two different units (eg AC Volts and dBm) or the measurement along with the selected range.
-
product
Programmable Linear DC Power Supply, 3 Output, 0-32V/0-3.2A, 2.5V/3.3V/5V/3.2A
T3PS3000
Teledyne Test Tools new T3PS3000 is a Linear Programmable DC Power Supply with a 4.3 inch TFT LCD display. It has three isolated outputs: two adjustable channels and one selectable channel from 2.5 V, 3.3 V, and 5 V with output short and overload protection for each channel. Support for series and parallel operation of the two main channels extends its flexibility beyond the standard specification. The T3PS3000 features include programmability via USB or LAN, a graphical display of power waveforms, and the high resolution numeric display of voltage and current. Typical users are Education, Production, and Design and Development.
-
product
LED Lighting Drivers
Renesas' dimmable AC mains LED driver with PFC and primary side regulation provides all of the features required for high-performance dimmable LED ballast designs and supports AC or DC input, isolated or non-isolated flyback and boost topologies.
-
product
Leeb Hardness Tester
THL210
LCD display of 128×64 matrix with back-light, showing all functions and parameters. Converts to all common hardness scales (HV,HB,HRC,HRB,HRA,HS). English displaying and easy and convenient menu operation. Powerful PC Software available and USB 1.0 interface and USB with Protective Membrane. 7 types of Impact Device optional, which don't need to be recalibrated when changing them. Memory of 600 groups data（impact times:32～1）. Lower limit setting and sound alarm. Material of “cast steel” is added; HB values can be read out directly when D/DC impact device is used to measure “cast steel” work piece. Printer be separated from main unit and copies of testing results can be printed as required. Normal battery AAA and big power store while USB connected and charging controlling circuit. Inbuilt function of Software Calibration.
-
product
Video Signal Generator
MSPG-3233RS
Analog was a main item in display device industries at the past time, but from now on, the digital is getting developed with multi-function and large-sized resolution. Preparing for this change, this signal generator is an essential equipment of CRT, LCD, PDP, TV, D-TV display device industries, which was made for generating analog signal, digital signal, and TV signal, D-TV signal, HDCP Code simultaneously and sufficiently examining a large-sized display device.
-
product
DAQ Modules
Q.series X DAQ Modules for Ethernet, CAN and ProfiNet
All Q.series X DAQ systems possess the same measurement capabilities and performance, regardless of form factor. The main differentiating quality between the XL and XE versions of Q.series X is the Fieldbus communication protocol (Localbus or EtherCAT), which can be interchanged on Q.series X modules using a simple firmware update.
-
product
Copy Tools
DemiXG2020
10GB (*) per minute high speed data transfer.High speed copy and deletion at original hard disk speed.(* Transfer speed varies according to performance of connected devices.)Light weight and compact with 1.5kg main unit.Portable, perfect for on-site copy, backup, and data deletion.Built-in SAS interface.SAS hard disks used for servers, etc. are supported. (SATA II is also supported.)Built-in deletion function and quick diagnostics function.Deletion report can be created with the terminal software (sold separately).
-
product
Network Cable Tester
AVJoG
*A two box solution to testing AV panel installations. *Each box only 150mm square.*Easy to use with only one button operation. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *6V battery or Mains use.
-
product
High Power Dry SIL Reed Relays
Series 114
SIL relays - Will replace mercury wetted relays in some applications. 1 Amp switching, 2 Amps carry. AC Mains voltage switch.
-
product
LED tester
Ecopia's LED tester is good to measure both electrical(I-V curve) and optical(Spectra, Light intensity) properties of LED chip, LED lamp, SMD type at the same time.It also makes it possible to see LED sample's construction , seeing through microscope. LED tester main body flow input current ,and emitted light from the LED sample is focused on lens of microscope.From this process, our LED tester can provide repeatable tested results and minimize error values and improve convenience of how to use.
