Mains
chief conduit of electricity, gas or water distribution.
-
product
Hall Effect Measurement system
HMS-3300
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
product
Voltage Stabilizer
MS 7643
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
product
HandyScope HS4 DIFF: 25 MS/s 100MHz BW, 4 Channel, USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS4-25-DIFF
The Handyscope HS4 is the successor of the popular Handyscope HS3. Built for customers that want to extend their measuring capabilities even further, this powerful computer controlled measuring instrument now features four input channels. The HS4 has just like it's predecessor the four main measuring instruments: a Multimeter, an Oscilloscope, a Spectrum analyzer and a Transient recorder.
-
product
Power Disturbance and Power Quality
MAVOWATT
ndustry, commerce, health care services, banks and other service providers are extremely dependent upon electrical and electronic systems. These systems influence mains quality themselves in many ways, but they react extremely sensitively to any disturbance as well.
-
product
E/O Converter
LTX-510
The LTX-510 Electrical to Optical Converter is a convenient device that is intended to transmit analogue or digital signals to a remote location via a multi-mode fibre optic cable. The main applications are situations in which the signal of interest has a high common mode voltage with respect to the measuring equipment.
-
product
Video Signal Generator
MSPG-7800S
Analog was a main item in display device industries at the past time, but from now on, the digital is getting developed with multi-function and large-sized resolution like 4Kx2K. Preparing for this change, this signal generator is an essential equipment of LCD, LED, PDP, D-TV, TV, CRT display device industries, which was made for generator analog signal, digital signal, TV signal and D-TV signal, HDCP, code simultaneousl and sufficiently examining a large-sized display device.
-
product
Beam Directional Power Supply Mains
SiteX CP160D
The CP160D is the lightest and most compact generator of the CPSERIES. Featuring a built-in Beryllium window, it is the perfect generator for the inspection of light alloys such as aluminum, magnesium or fiber based materials like glass and carbon, as well as the greater thickness of steel. In fact, with its penetration capacity that is capable of reaching up to 37 mm of steel, the CP160D is able to execute many different types of NDT tasks without the need to ever have to add extra accessories.
-
product
Automatic Fiber Optic Stripping Machine - FBT-800
Shanghai Fibretool Technology Co.,Ltd.
Fibretool offers advanced, field-proven fiber stripping machines for efficient processing of coated, buffered, and jacketed glass fiber.The FBT-800 is a pneumatic fiber stripping machine specifically designed for buffer, coating stripping of optical fiber cables and ribbon fibers. The compact machine strips lengths from 5 up to 35 mm with extremely fast cycle times. Absolute precision, high cost effectiveness, and fast return on investment are the main characteristics of this machine.
-
product
RACK SYSTEMS
Most of ETL's sub-systems are designed to fit standard 19" racks. We produce RF distribution equipment for a wide range of applications in the RF chain. On satellite downlinks this is between the LNB and the modem or receiver; and on satellite uplinks it is between a modem and a BUC.Reliability, Resilience and RF performance are designed into all our equipment wherever possible. Scaleability and Adaptability also influence the design process.The main product families are shown below, with further selection of products via functionality and design.
-
product
Digital Circuit Breaker Analyzer
CT-8000 S3
The CT-8000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-8000 S3 is available with 3 (part number 9103-UC) or 6 contact timing channels (part number 9104-UC). The CT-8000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Also, an outstanding feature of the CT-8000 S3 is the ability to perform dynamic resistance tests on circuit breaker contacts.
-
product
Electronic Loads
The DSO and DSOT series electronic loads are designed using advanced linear technology.The DSO series offers two main functions: constant current and constant resistance. However, these loads can absorb full power between 20% and 100% of the acceptable input voltage thanks to the autoranging mode.For more extensive requirements, we offer 'DSOT' models that also include constant voltage and constant power functions. These functions are essential for testing voltage generators such as automotive alternators or photovoltaic panels to determine their power curve. In addition, DSOT models have a basic '0 Volt' characteristic, which means they can be used with input voltages as low as 0 Volt. However, they still maintain a high reaction speed, which can reach 1V/us and 8A/us.
-
product
Cell Production
JRT Photovoltaics GmbH & Co. KG
The production of lithium-ion cell batteries includes the three main process stages of electrode production, cell assembly and formation and aging. Automation is a critical factor for success, particularly in the process stage of cell assembly.
-
product
Dynamic Weighing System for Excavators
Loadtronic 3E
The load in the bucket is weighed during normal lifting cycle. The weighing can be started automatically or manually. The display will show the weight currently in the bucket, and the running total. Also, the number of buckets delivered is shown. The weighing system can be used as a tool toavoid over- and underloading of trucks. All loadings are stored in the main unit and can be retrieved either for printing a receipt or for transfer to PC (USB stick/ SMS). Databases of customers, materials etc. can be transferred between the office PC and the Loadtronic 3E system (using USB stick). The files can be viewed and edited in MS Office Excel or Notepad.
-
product
Fiber Optic Test System
OPTOWERE-S100 (Fiber Optic Test System)
The frame of FOTS system consists of the Main control part and the Slot mounting part. The Main control part is in charge of control and interface of the system and the Slot mounting part can hold up to maximum 8 slots, which are modularized according to each function and come out in five kinds. This integrated test system is designed to help manage the test and measurement related to optical communication and component. And the modular architecture of FOTS allows for customized configuration so that the slot of LD Driver, 2 channel VOA, 1 X 4 switch, WDM EDFA and C + L – Band ASE Source can be chosen according to user’s necessities. Main control part and each function module are run by effective and multi-functioned system control program in the base of high speed remote interface, GUI display and the discriminative high speed driving of module and system. This system can provide variety manufacturing and laboratory applications such as general quality test and reliability test of optical component and optical signal transmission test through efficient linkage with other system.
-
product
Environmental Chamber
REXMED REC-200
MOD. REC-200, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 1,892 Watts, 6,455 BTU/hr, 1,630 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Carpet Dynamic Loading Tester
TF610
TESTEX Testing Equipment Systems Ltd.
Carpet Dynamic Loading Tester, by simulating walking to determine the effects to two of the main actions of walking: compression, and the shearing effect at the edge of the shoe.
-
product
Powertrain ICs for ICE/HEV/EV
ST's powertrain ICs cover a variety of functions including voltage regulators, sensor interfaces, and load or motor drivers, which are the building blocks of typical Engine Control Units (ECU) found in a vehicle's main applications (engine management systems, transmission control systems, alternator regulators, etc.).
-
product
Socket Tester
*Power supply from mains : 200-230V AC*Transmit AC signal through concrete walls; Shielded / armored cable*Internal fuse protection
-
product
Belt Tension Tester
BTT2880
Main used in belt tension measurement, can also be applied to measure the tension of objects such as tapes, wires. Widely applied in industries of automobile, textile, cables, wires, plastic films, paper, printing.
-
product
Solid-State And Electromechanical Relay Products
Relay is the name for a switch that is operated electro-mechanically or electronically. Their main task is to make and break connections to control the flow of current in electrical circuits. They’re used for various purposes ranging from validating semiconductors to interfacing low power computers or microcontrollers with high power machinery.
-
product
Field Bag
1048
TESCO has recently updated the Field Bag. The newer Field Bag is slightly smaller than the previous version. The bag features a large main compartment with a removable divider, and two smaller side pockets. The Field Bag comes with a shoulder strap, for ease of mobility. The Field Bag measures 16″ x 8.75″ x 7.5″ (L x H x D).
-
product
Diagnostics
Boston offers the most comprehensive stand-alone diagnostic solution to cover all main European and Asian vehicle functionality. Introducing the b-Touch, a market leading tool in the world of vehicle diagnostics.
-
product
Probes
Replacement or Additional 9V 230V/110V Power Supply. Requires a standard IEEE mains interface cable
-
product
High Precision TMAH Concentration Monitor
HE-960H-TM-S
Accurately measures the concentration of TMAH (Tetra Methyl Ammonium Hydroxide), which is the main component of the photoresist developer solutions in semiconductor manufacturing. Repeatability: within +/- 0.003%. Measurement range : 0 - 3 %. Have the chemical resistant carbon sensor.
-
product
Copy Tools
DemiXG1020
Main unit weight is approx. 1.4kg, ultra compact and thin designResults in superior portability, perfect for on-site copying, backup, and data deletion.High speed data transfer at 10GB per minute (*1).(*1 Transfer speed varies according to performance of connected devices.)Reverse copy functionCan copy from last portion of HDD. Perfect for restoring data.Built-in evidence preservation functions including hash generation (MD5, SHA1, and SHA256) and creating DD images, etc.Built-in deletion function and quick diagnosis functionDeletion report can be created using host software (sold separately).
-
product
Selective Level Meter
Model SLM620
- Digital Synthesized Local Oscillator- Two Selective Bandwidths : 20Hz, 3.1KHz- Wideband, Low Noise and Low Distortion Measurements- dB/dBm Operation- High Frequency Stability- Internal Calibration Facility- Recorder Outputs- Frequency Tracking Facility with Level Oscillator SLG620- Storage of Nine Spot Frequencies- Reference Level Set Facility- Autotune Feature- Operates on AC Mains or Internal Rechargeable Battery- Built in charger- Graphic LCD Display with Backlight
-
product
Reactive Energy Regulator
MASTER
Lifasa - International Capacitors, SA
It measures the reactive power needs of an installation and gives the corresponding capacitor connection and disconnection orders to keep the cos φ preset. At the same time it allows to measure the main parameters of an installation (voltage, current, harmonics, active power, reactive power, etc.), by using 1 or 3 current measurement transformers.
-
product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT MXP+
SCOT MXP+ measures, displays and prints CLOSE, OPEN and CLOSE-OPEN time of 2 Main + 2 PIR contacts per pole, 3 poles simultaneously, ensuring measurement of 6 Main + 6 PIR contacts simultaneously. Ideally suitable for CBs having PIR contacts & multiple breaks per pole
-
product
S2 Unicolor Sensors
ULP-S2 SCI/V
The Universal LightProbe S2 Unicolor Sensor is designed for the intensity test of any single one of the five main LED colors (blue, green, yellow, orange, and red) plus white and Infrared (700nm to 1,000nm). Implemented in a unique and customizable 2-Part solution, the S2 Unicolor Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times:<10mS capture time; 65mS overall response time; intensity output of correct color only.Fiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
product
Radiation And Process Monitoring Systems
ProTK
Monitoring of the main steam line for leakages in a PWR nuclear power plant with a wide-range gamma ionization chamber.
