Impulse Current
-
product
Impulse Cable Tracer
Wayfind'r
The WAYFIND'R Impulse Cable Tracer was originally designed for electric utility use to accurately identify the route of buried secondary cables. Because the WAYFIND'R imposes an audio frequency signal on the cable, the signal is not induced into adjacent cables or pipes, eliminating false signals. The WAYFIND'R may also be used fro tracing indoor wiring and buried shielded primary cables.
-
product
Current Sensing Chip Resistors
CS
*3W rating in 1W size, 1225 package*High purity alumina substrate for high power dissipation*Long side terminations with higher power rating
-
product
Clamp type AC Current Sensor/for Low Leakage Current Measurements(ZCT Series)
ZCT-110S
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
product
AC Current Probe 10 mV/A, 600A, 12 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable
T3RC0600-HF
AC Current Probe 10 mV/A, 600A, 12 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable.
-
product
Resistive Current Tester
Weshine Electric Manufacturing Co., Ltd
Long Distance Digital Zinc Oxide Arrester Resistive Current Safety Testing Set
-
product
Current Transformers
Rishabh Instruments Pvt. Ltd.,
Rish Nano CT is a very reliable, efficient and robust current transformer for measurement of AC current. It provides 100 mA AC output. It can be used in Circuit breakers. Earth Leakage Protection.
-
product
Device Current Waveform Analyzer, 1 GSa/s, 14/16-bit, 2 Channel
CX3322A
The CX3322A is a 2-channel model for engineers and researchers who just need one or two current waveform measurements at one time. Using a single channel current sensor (CX1101A, CX1103A) and a passive prove interface (CX1151A) enables power measurements. The bandwidth and the memory depth per channel are option and can be selected from 50 MHz, 100 MHz and 200 MHz, and 16 Mpts, 64 Mpts and 256 Mpts, respectively. The number of channels is not upgradable, but upgrade products for both bandwidth and memory depth options are also available for customers who need more performance after purchasing the product. You could also minimize the initial investment for later upgrade with this affordable 2-channel model.
-
product
Leakage Current Tester
TOS3200
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
-
product
Current Sensing Resistors, Metal Plate Type -MS, MB
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-911
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Device Current Waveform Analyzer, 1 GSa/s, 14/16-bit, 4 Channel
CX3324A
The CX3324A is a 4-channel model for engineers and researchers who need more than two channels for current waveform measurements at one time. Using a passive prove interface (CX1151A) with a current sensor (CX1101A, CX1102A, CX1103A) enables power measurements. The bandwidth and the memory depth per channel are option and can be selected from 50 MHz, 100 MHz and 200 MHz, and 16 Mpts, 64 Mpts and 256 Mpts, respectively. Upgrade products for both bandwidth and memory depth options are also available for customers who need more performance after purchasing the product. 8-channel digital channel (CX1152A) can be used with this 4-channel model so that you have more flexibility of triggering.
-
product
Ultrafast Photodetector with Current Monitor, 700 - 870 nm, DC - 25 GHz, FC/PC
DXM25CF
The DXM25CF Ultrafast Detector is a DC - 25 GHz, fiber-coupled, GaAs-based photodetector designed for applications in the 700 nm - 870 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.
-
product
Eddy Current Flaw Detector
US-525M
United Western Technologies Corp
The US-525M multi-channel eddy current testing instrument is a rugged industrial rack-mounted instrument offering multi-channel testing, integral digital strip chart, as well as Ethernet control and data transfer to meet your in process testing requirements. This instrument offers up to eight channels, with a frequency range of 20 Hz to 10 Mz, a high signal-to-noise ratio, a bright 12-inch diagonal color LCD flat-panel screen, and data storage of 32 Gig. It offers input/output (I/O) capability, USB and Ethernet connectivity, as well as three discrete alarm gates with independent outputs per channel. for your on-line bar, tube, wire and specialty component testing needs.
-
product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TC
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
product
DC Bias Current Source
DU2020/2030/2040
Delta United Instrument Co., Ltd.
Frequency: 10KHz - 200KHz Veracity:3% + 3 digitsTiming: 0.1 - 999 H, settable 3 1/2 bits LCD Display
-
product
High Current Short Circuit Loop Impedance Meter
AMZC-310S
Measurement of very small short-circuit loop impedances (with resolution of 0,1mΩ) using the current of 150A under 230V, maximum 280A under 440V, or measurement using the current of 23A under 230V, maximum 42A under 440V
-
product
Current Mirrors
Analog Devices current mirrors are precision, high dynamic range, wide variable supply parts used for optical power monitoring, voltage biasing with current monitoring, and voltage-to-current conversion. Our current mirrors can monitor current down to as little as 3 nA and as much as 3 mA, with a linearity of 1% or better. The current dynamic range is 120 dB or 6 decades of current range, while the overcurrent protection feature in our devices forces the input pin to ground to avoid part damage. Over temperature (–40°C to +85°C) and process, the dynamic range only suffers 10 dB at the lower end of the range.
-
product
Current Probe
PA-699
*High sensitivity: 1mA, High frequency: 1.5MHz. They are all 10 multiple calculation. Calculation is not making mistakes.*Max measuring current: +/- 40A DC / 80 Ap-p*Max sensitivity: ≧1mA*Bandwidth: DC ~ 1.5 MHz*Rising Time: 0.23 uS*Overload indicator*1V/A, 0.1V/A 2 ranges selectors*Input power switching (priority circuit) and battery available*Dispatching design, high durability
-
product
150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 2 meter cable
CP150B
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
311 HP Eddy Current Chassis Dynamometer
CM-51SR-EC
Weight Capacity: 25,000 lb (11,340 kg) per axleRoll Brakes: pneumatically-actuated discShipping Weight: 5,100 lb (2,312 kg)Capacity: 311 hp at 45 mph (232 kW at 72 kph)Rolls: 20 by 36 in. (508 by 915 mm) long, 2 fixedPit Required Depth: 25 in. (635 mm)
-
product
Impulse Voltage Generator
Shanghai Sanki Electronic Industries Co., Ltd.
Impulse voltage generator Impulse voltage generator is mainly used for test products such as power equipment to perform lightning impulse voltage full wave, lightning impulse voltage chopping, operating impulse voltage wave and steep wave impulse voltage test, to inspect insulation performance. The technical indicators comply with national standards and IEC standards.
-
product
AC/DC Current Probe (2-Channel), 3 MHz, 50 UA
N2820A
The N2820A 2-channel current probe connects to two oscilloscope channels to provide simultaneous low- and high-gain views for wider dynamic range measurement, while the N2821A 1-channel current probe provides one user-selectable view at a time.
-
product
Sound Harmonics and Current Analyzer
H74050100
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
-
product
20A Auto Current & Voltage Tester
7610
Peaceful Thriving Enterprise Co Ltd
Fast, accurate and safe current measurement at the fuse box.Ideal for fault-finding on car and commercial vehicle electrical circuit.
-
product
Current Measurements Of PWM Or Inverter, AC/DC 1~50A, Φ16mm
CTF-50DC-U24V
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 1~50A*Current measurements for PWM or inverter
-
product
Calibrator, Calibrated, Current, 185 mm, 78 mm, 38 mm, ± (0.25% FS +1 digit), ± (0.5%FS + 1 digit)
72-6694 CAL
The 72-6694 CAL from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
product
Resistors for Calibration of Current Measuring Systems and Sensors/Transducers
ChenYang Technologies GmbH & Co. KG
Is designed and made according to the Standard JB/T8225-1999 for DC resistors used in laboratory and electrical engineering.By using full closed structure and automatictemperature control it ensures resistor good long-term stability and small temperaturecoefficient. This DC resistor is very suitablefor DC current measurement and calibration of current measuring systems and current sensors. The maximal measuring current is 100A with measuring accuracy of ±0.02%
-
product
High Current Switches
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
product
Automotive Current Tester LCD Display
77102
This automotive current tester with LCD display, plugs directly into the fuse box and can be used on mini, standard and maxi fuse connections. Blades may get hot during use and care should be taken for 2mins whilst they cool down. Fits mini and maxi fuses. Current range 0-80AMP. Safe and easy way to check automotive current.
-
product
Voltage, Continuity, and Current Tester
FLIR VT8-Series
The FLIR VT8-Series are high-quality voltage, continuity, and current testers. They feature an optimized, open-jaw design that can fit into tight spaces and reliably measure large-diameter cables. The VT8-600 carries a CAT III-600 V/CAT IV-300 V safety rating and a 100 A/600 V measuring range, while the VT8-1000 carries a CAT III-1000 V/CAT IV-600 V safety rating and a 200 A/1000 V measuring range. Extensive measurement features make the VT8-Series versatile tools – just one meter can get the job done.





























