Impulse Current
-
Product
Dual Voltage Buffer with Current Drive
BUF-01
-
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
-
Product
3-Phase Current Meter With 3 X 75A Clamp-On CT
EVA-2210
-
LoRaWAN® wireless connectivity3 x 75A Clamp-On CTBattery life up till 3.5 years@25 °C, 60 mins interval settingEasy to deploy and maintain
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-912
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Rogowski AC Current Probe
RCP500
-
Shenzhen Micsig Instruments Co., Ltd.
Adopts the Rogowski coil current measurement system: within the range, the output signal of the system and the current signal to be measured are always linear, so the accuracy will not change with the current; The RCP500 measures AC current up to 500A pk, minimum to 200mA pk, with bandwidth ranging from 15Hz to 300KHz, 1% accuracy, and has less than 2mV noise. Directly powered by Micsig UPI interface, realise auto scaling setup,
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40P
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC 0.1A～500A*Current measurements of feeder
-
Product
DC Current Bias Supply
DC1000A
-
To guarantee the quality and performance of inductive components such as inductors, chokes and transformers they are tested at their real-life operating point. If the inductor is designed to carry a DC current, then its inductance must be measured with that DC current present. Until now, these measurements were made by an LCR meter connected via special interfacing to a DC bias supply available only from the manufacturer of the LCR meter. The unique NEW DC1000A can be used with any precision LCR meter and connects simply into existing test fixturing.
-
Product
High Current Probes (Battery Contacting) HCF73206B200G300A
1165580
-
The High Current Probes (Battery Contacting) HCF73206B200G300A is a cutting-edge probe designed for precision applications where reliability and performance are paramount. With its basic contact probe design, it offers a compact pitch of 2.54 mm and operates efficiently across a temperature range of -45°C to +200°C, making it suitable for various demanding environments. This probe is engineered to handle continuous currents of up to 20 A, showcasing its ability to perform under rigorous conditions while maintaining a typical contact resistance of only 10 mOhm.
-
Product
High Current Probes (Power Electronics) HCF32007S135N130
1003391
-
The High Current Probes (Power electronics) HCF32007S135N130 are designed for precision applications in various electronic environments, ensuring reliability through their robust and high-performance features. With a continuous current rating of 12.00 A, these probes are capable of handling significant loads while maintaining a low typical contact resistance of 20 mOhm, making them ideal for power electronics testing and integration. The temperature range of -45°C to +200°C ensures functionality in diverse operating conditions, while the basic contact probe design contributes to their versatility in various applications.
-
Product
High Current Probe HCF77216B100G300A
1165652
-
The High Current Probe HCF77216B100G300A (item number 1165652) is designed for safe transmission of high electrical currents in test and contacting applications. HCF77216B100G300A focuses on current capacity and low transition losses, as required in battery testing, formation and other e-mobility applications. For HCF77216B100G300A, contact resistance, contact force and thermal behavior must be considered together because they influence voltage drop and temperature rise at the contact point. The intended application area for HCF77216B100G300A includes battery and power-electronics testing. The electrical rating of HCF77216B100G300A combines 20 A continuous current with 10 mΩ typical contact resistance. For HCF77216B100G300A, spring force is 300 cN at a nominal travel of 4 mm.
-
Product
High Current Probes (Power Electronics) HCF71306B230G150
1024197
-
The High Current Probes (Power electronics) HCF71306B230G150, with order code 1024197, is designed for reliable and efficient operation in demanding environments, accommodating a temperature range from -45°C to +200°C. These basic contact probes feature a robust design with a pitch of 4.00 mm, making them ideal for high-performance applications in power electronics. With a continuous current rating of 30 A and a typical contact resistance of only 8 mOhms, they ensure minimal energy loss, contributing to overall system efficiency. The mechanical specifications highlight a preload of 70 cN and a spring force of 150 cN, providing a nominal travel of 2.80 mm and a maximum travel of 3.50 mm, complemented by a pointing accuracy of +/- 0.10 mm.
-
Product
OEM Current Input0 to 20mA
TGPR-0800
-
A current input data logger that is supplied uncased so that it can be built into custom applications.The TGPR-0800 can be used to record the output from a number of industry standard 4-20mA sensors. Common applications include pressure and flow rate monitoring.
-
Product
High Current Probes (Plug Connectors) HCF76289B310100620G300
1023602
-
The High Current Probes (Plug Connectors) HCF76289B310100620G300 are designed for robust connectivity in demanding environments. Capable of handling continuous currents up to 40A, these probes ensure reliable performance even in extreme temperatures ranging from -45°C to +200°C. The innovative design, highlighted by a 4mm pitch and a basic contact probe structure, underscores their suitability for high-performance applications. This product features exceptional pointing accuracy of +/- 0.05mm, making it ideal for precision tasks where reliability is paramount.
-
Product
32CH 4-20mA Current Sink Card
SET-1250
-
Each channel provides an isolating relay and a short-circuit MOSFET with which opening and short-circuit errors can be simulated. The short-circuit MOSFET has overcurrent protection with integrated current limitation.
-
Product
SHDB9M-DB9F, Current Transducer Shielded 9-Pin D-SUB Cable, 3 m
786879-03
Analog Cable
SHDB9M-DB9F, Current Transducer Shielded 9-Pin D-SUB Cable, 3 m
-
Product
Magnetic & Current Sensors
-
From the International Space Station to a simple electronic compass, we can provide a solution to meet your magnetic semiconductor needs. The F.W. Bell® product line was founded in 1944. Since then we have been a pioneer in developing instrumentation to measure electric current and magnetic fields.
-
Product
High Current Probes HCF77305A300U300
1016460
-
The HCF77305A300U300 high current probe is designed specifically for power electronics, offering exceptional performance across a range of applications. This specialized probe is capable of handling continuous currents up to 30 amperes and operates effectively within temperature conditions ranging from -45°C to +200°C. Its robust construction and engineered design make it ideal for precise measurements in demanding environments, ensuring both reliability and accuracy during testing procedures.
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-30S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Ultra compact size*AC 1mA～100A
-
Product
High Current Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40PS
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～500A*Current measurements of feeder
-
Product
Residual Current Protection
-
Solutions to ensure the safety of people and installations against any ground currents. Available with ultra-immunized system as an essential solution to avoid financial losses due to outages caused by inadvertent trips. Specially designed to protect industrial installations in AC networks (type A), installations with both AC and DC components and DC-only installations (type B). Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
-
Product
High Current Probes (Battery Contacting) HCE04FA52G10E089
1167327
-
The High Current Probes (Battery Contacting) HCE04FA52G10E089 is designed specifically for robust electrical performance across a wide temperature range. This contact probe operates efficiently between -45°C and +200°C, making it suitable for various critical applications that demand high reliability and durability. With a continuous current rating of 40A and a typical contact resistance of only 2mΩ, the HCE04 model ensures optimal electrical connectivity and minimal power loss, which is essential in high-stakes environments.
-
Product
High Current Probes (Battery Contacting) H349M5KB
1024195
-
The High Current Probes (Battery Contacting) H349M5KB is a highly specialized tool designed for precise and effective electrical testing. It features a robust design suited for high continuous currents of up to 100.00 A, ensuring reliability in demanding applications. The probe is constructed with meticulous attention to detail, including a 7.60 mm pitch which significantly enhances its usability in various settings. The compact dimensions—58.25 mm in total length and an outer diameter of 6.50 mm—make it easy to handle while ensuring compatibility with a variety of electronic components.
-
Product
Leakage Current Tester
-
Premier's Leakage Current Tester (also known as Hipot Tester) simulates the effect of a person touching exposed metal parts of a product and detects whether or not the leakage current that would flow through the person's body remains below a safe level.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-22F
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for leakage current measurements*Ultra compact size*AC 1mA～100A
-
Product
Eddy Current Test System
CIRCOGRAPH® Product Family
-
Foerster Instruments, Incorporated
The CIRCOGRAPH eddy current test system with rotating probes guarantees maximum detection sensitivity for exposed longitudinal surface defects on bright material. The test system is primarily used for wire drawing machines, Cu tube rewinders, and finishing sections in the bright steel sector. The individually tailored test systems by FOERSTER can be fitted with rotating sensors or CIRCOSCAN rotating discs. They scan flat and profiled material, e.g. when testing rails and billets.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-23
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～120A*Current measurements of terminal feeder
-
Product
Current Integrated Sources
CIS
-
The CIS current integrated source was designed to provide a stable alternating current source for the electricity meter test equipment, and in laboratories. The output current is isolated and independent from the mains voltage. Different CIS versions are available depending upon the values of output power and output current required.
-
Product
Primary Current Injection Sets
-
Protective devices such as relays, overload Coils, Circuit breakers and CTS etc. must be checked regularly to ensure that they are always ready to operate correctly, Routine current injection testing will quickly detect faulty or incorrectly adjusted protection circuits / devices & will be possible to prevent serious damage to the system. Primary injection kit is designed to operate on single phase 230/240 volts AC 50 HZ to develop smooth & continuous test current as for loading, calibrating, and testing of CTS, Bimetal Relays, Protection Relays etc. The test set gives high current output at low cost and with inherent safety. The primary current injection testing checks all parts of the protection system by injecting current down the cable / bus bars. The application of the primary current injection sets is to ascertain the current carrying capacity of any Conductor, insulator, connector or calibration of CTS / Bi-metallic relays etc.
-
Product
High Current Probe HCE06MB11S24E130
1040075
-
The HCE06MB11S24E130 High Current Probe represents a significant advancement in high-performance connectivity solutions, specifically designed for demanding electrical applications. With a robust enduring temperature range of -45°C to +200°C, these probes excel in various environments, ensuring reliable performance under thermal stress. Featuring a pitch of 12 mm (472 mil), the probes are engineered for applications requiring high current transmission capabilities, accommodating continuous currents up to 100 A. The standard contact resistance is impressively low at just 5 mOhm, enhancing the efficiency of electrical connections.
-
Product
Split type AC Current Sensor
CTF-50A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of terminal feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
