- Pickering Interfaces Inc.
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 0.5m, Spring Latch
40-972A-068-0.5m-MU
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
Pointer Insulation Resistance Tester
HT2533 / 772
Wuhan Huatian Electric Power Automation Co., Ltd.
Suitable for measuring insulation resistance of large capacity transformer, transformer, generator, high voltage motor and lightning arrester.
-
product
20-Pin GMCT Cable, Male to Male, 16A, 2m
40-970B-020-2m-MM
The 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Cable Fault Location Equipment
Cable fault location by electromagnetic and acoustic methods (with high-voltage pulse transmitter, which is not included into the set)Detection of insulation deterioration on cables by contact and non-contact methods
-
product
Cable Diagnostic Tools
For non-destructive diagnostic testing to determine the quality of a cable’s insulation with minimal risk of failure, HVI recommends tan delta and partial discharge testing for valuable diagnostic data about cable insulation integrity. Both use a VLF source to perform elevated voltage, off-line testing. Tan delta testing measures insulation health, while PD identifies specific problem areas and assesses their severity.
-
product
20-Pin Scorpion Cable, Female to Unterminated, Cut Ends, 20A, 1m
A020AFR-C-2A100
This is a 1m long female to unterminated 20-Pin Scorpion cable assembly with cut ends constructed from 19/0.41 (14AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
High Insulation Digital Clamp Tester
HCL-5000KN+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Wide AC current measurements for 0.01A～500A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).・Auto power off function and Splash proof structure.
-
product
Insulation Multimeter Series
Insulation Multimeter is a new category of test tool that combines a full featured True-rms DMM and a megohmme- ter. It's an integrated tool for maintaining and troubleshooting motor systems, electrical distribu- tion, and production equipment.
-
product
PXI 8x SPST High Voltage Reed Relays
40-310-001
The 40-310/320 range of high voltage switching modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
25-Pin D-Type Male Connector Block
40-965-025-M
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m HV, Exit Towards Pin 1
A050DM5-T-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends
A068SFR-T-6A200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Multifunction Electrical Installations Meter
MPI-520
The MPI-520 multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520 is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.Wide range of standard accessories enable to perform all necessary measurements and safety test. Highly professional portable multifunction meter with memory of measured parameters.
-
-
product
Leakage Test
Leakage current and discharge current depend on the insulation of the device. The measurement simulates various fault situations that could occur during operation. The test determines whether the measured current is within the permissible limits and poses no danger to the user in case of a fault.
-
product
Cable Assembly, 50-Pin SGMC, Female to Female, 5A, 2m
A050FFR-050FFR-0A200
This is a 2m long female to female 50-Pin SGMC cable assembly constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
Hand Cranked Analog Insulation Resistance Tester
IRT20
UEi Test & Measurement Instruments
The IRT20 is a Hand-cranked Insulation Resistance Tester. With a insulation resistance range of 0.1 to 1000MΩ, 250, 500 and 1000V output ranges and accurate to with in one division. It is in a sealed, water resistant, rugged metal housing and is backed by a 1-Year limited warranty.
-
-
product
GMCT 26-Pin RF Cable Assembly, 75Ω, Male To Unterminated, 0.5m, RG179 Cable
40-979-726-0.5m-FU
This 0.5m long cable assembly is part of a range of cables suitable for applications using the Positronic 26-pin GMCT 75Ω RF connector. It is constructed from RG179 silver plated copper clad steel cable with FEP insulation and a bandwidth of 500MHz. Screwlocks are provided to secure the connector to the associated product.
-
product
Cable Tracers
180 CB
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
product
Short Circuit Locator for Power Cables
A910
The A910 is a short circuit locator designed for fault location in power cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A910 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total...show more -
product
96-Pin Micro-D Connector Block, Male With Backshell
40-965-096-M
This connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Transformer Resistance Testing
Transformer insulation resistance deterioration is one of the most common causes of transformer failure: a failing transformer is a costly replacement in an electrical system with the potential for a long downtime. If you fail to maintain your transformer with regular insulation resistance testing (as can be carried out by the Megger Transformer Ohmmeter (MTO) series of transformer test equipment) then it’s likely to fail before reaching its maximum operating life.
-
product
Testing Leads Assortment (16PCS)
3605A
Peaceful Thriving Enterprise Co Ltd
1. For use on the 6-24V circuits.2. 4mm connection for banana plugs.3. Facilities the measurement on connectors and components without destroying the insulation or the plug connection.
-
product
4-Pin Power D-Type Cable, Female to Female, 0.5m
40-970-404-0.5m-FF
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
Franklin Tester
TF-100
The measuring device Franklin tester is designed to measure the insulation resistivity of coating and its mineral components on the surface of electrotechnical steel sheet as well as applied enamel to generator stator core laminations according to the ASTM A717/ A717 M - 95 Standard. The device contain series connection which allow the data transmittion to PC.
-
product
Hybrid Wound Component EST Scanner
19035
Chroma Systems Solutions, Inc.
The quality verification test items for Wound Components consist of AC/DC Hipot tests and Insulation Resistance (IR) tests. Chroma integrates the above tests into the Hybrid 19035 Wound Component EST Scanner series to perform safety tests for motor, transformer, and heater related wound products. The wound component manufacturers performing quality verification testing will not only have reliable quality, but also can control product quality efficiently.
-
product
Cable Assy 25-Pin D-Type Male To Female 2m
40-970-025-2m-MF
The 25-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. male Screwlocks are provided to secure the connectors to their associated products.
-
product
Burn-in Room and Aging Test Chamber
Isolated type of burn-in room features: ●Separate the product and loading area, easy to control temperature and maintain. ●Temp. range: 40-70ºC±3/±5ºC, ●Temp. constancy: ±0.5ºC ●Uniformity: ±3ºC ●Test frame materials: painted stainless steel or a combination of forming aluminum ●Insulation: with PU foam ( doors with double glazing ) insulation, so that the internal temperature is not subject to external factors, to achieve power saving effect ●Product hierarchy placement, Selection of lay...show more -
product
Hipot Wire Harness Testers
NX Hipot
* 50 to 1500VDC Hipot Testing* 50 to 1000VAC (optional) * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
product
Space Charge Measuring Equipment
PEA
The increasing request for energy quality and, thus, insulation system reliability, associated with significant steps in the manufacturing of new insulating materials, are pushing strongly the research on new techniques for the diagnosis of insulation ageing.
