Filter Results:
Products
Manufacturers
Applications
Solderability
-
product
Solderability Tester
LBT210
Microtronic Microelectronic Vertriebs GmbH
Microtronic's LBT-210 solderability tester has software that offers statistical information such as mean value, standard deviation, etc. A camera option offers video of the test cycle and storage in memory with the appropriate test measurements and data. Additionally, it has the feature to test under nitrogen. This function can be switched on in the software. An enclosure that is flooded with nitrogen lowers and rises with the device under test.
-
product
Multicore Universal Solderability Tester
MUST System 3
The MUST System 3 is the latest technological evolution of the original Multicore Universal Solderability Tester (MUST) that grandfathered all modern solderability test standards. It remains the unquestioned industry benchmark for solderability testing.
-
product
Solderability Tester
ZHX-35
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.14-2008Used to detect the self-solderability of enameled round wires and wire harness;Set variable temperature range and automatically maintain constant temperature;Under mechanical driven, samples would be withdrawn by the action of automatic insertion and lateral movement, free from vibration and noise;
-
product
3-Pin Power D-Type Connector, 40A, Male Without Backshell
92-960-003-M
This connector is designed to allow users to make a direct termination with soldered connections.
-
product
SHV Connectors
Pasternack SHV connectors category has several part numbers, most are RoHS and REACH compliant. SHV connector series in this category will terminate to coax or terminal. These SHV connectors are built to precise microwave and RF industry specifications. SHV connector items are built in jack or plug gender with 50 Ohm impedance. Connectors in SHV series are available in bulkhead, 4 hole panel or mountless options. These SHV connector designs include clamp/solder, crimp/solder or solder attachment methods. As with other over 40,000 RF, microwave and millimeter wave Pasternack products, this SHV connector series is in-stock. Not just are they in stock, but these radio frequency connectors will ship the same day as they are purchased.
-
product
25-Pin D-Type Male Solder Bucket
92-960-025-M
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
product
75 Ohm MCX Connectors
Pasternack 75 Ohm MCX connector category includes several part numbers, the majority are RoHS and REACH compliant. 75 Ohm MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These 75 Ohm MCX connectors are built to precise RF and microwave industry specifications. MCX 75 Ohm connectors are available in jack or plug gender with 75 Ohm impedance. 75 Ohm MCX connector products are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm MCX connector designs include crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this MCX connector series for 75 Ohm is in-stock. Not only are they in stock, these MCX 75 Ohm connectors will ship the same day as purchased.
-
product
Custom Bolt-On Strain Sensors
Our custom bolt-on strain gauge sensors are designed and manufactured to your application, based on your drawings and specifications, including all types of output formats. Ideal for dynamic load monitoring, capable of measuring and monitoring axle stress and weight with high accuracy.Do you have an application for strain gauge measurement that requires a quick and simple installation, repeatedly, in multiple locations? Perhaps you need a sensor with high environmental protection, which removes the necessity for time-consuming cleaning, complicated soldering and messy strain gauge adhesives?
-
product
78-Pin D-Type Male Without Backshell
92-960-078-M
This connector is designed to allow users to directly terminate cables with soldered connections. 78-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module.
-
product
Solder Wettability Tester
5200TN
Amid the rapid progress in miniaturization of electronic components in high-density mounting, a long-established company that has been manufacturing solder wettability testers for about 40 years has developed a solder wettability tester compatible with the latest micro electronic components. and is the top model in the history of solder checkers with improved operability. * Wetting stress is proportional to the circumference of
-
product
Eurocard Plugbord
E160-3U-2
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Voltage and ground buses around board perimeter on both sides. Bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
product
26-Pin D-Type Connector, Female
40-960-026-F
This connector is designed to allow users to directly terminate cables with soldered connections.
-
product
QFP-to-PGA Motorola 68340 144-Pin Adaptor
97-68340
144 Pin QFP to PGA Adapter for Motorola 68340. Convert surface mount QFP packages to a 15 x 15 PGA footprint. Reduce costs by using less expensive QFP packages to replace PGA footprints in existing designs. Pins are mechanically fastened and soldered to board using Aries patented process, creating a reliable electrical connection and rugged contact.
-
product
20-Pin GMCT Female Connector, 10A, Without Backshell
92-960-020-10A-F
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
6U Processor Blade
CP62007
LinkedHope Intelligent Technologies Co.,Ltd.
CP62007 is a 6U processor blade based on Intel’s 4th generation core i7/i5 processors using 22nm process technology, supporting up to four cores / eight threads at 2.4GHz. CP62007 supports up to 16GB onboard soldered low voltage DRAM with ECC. It also offers up to 64/128GB SLC/MLC onboard SATA SSD for installing operating system and drivers. The onboard design of memory and SSD enhance the anti-shock and vibration performance dramatically.CP62007’s onboard processor integrates Intel® HD Graphics 4600 controller, supporting a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA. And the VGA resolution is up to 2048x1536. With HDMI/DP/eDP outputs, the resolution can be up to “4K”.CP62007 supports 1x VGA and 2x DP/HDMI/DVI, up to 3 independent or cloned displays.CP62007 uses high speed CPCI connectors on J3 and J4 position for transferring high speed serial signals, such as PCIe2.0, USB3.0 and SATAIII. And the foot-print of high speed connectors are fully compliant with CompactPCI specifications.
-
product
Solder Cup Connector Kit
Y1140A
Used to build custom cables for 34922, 34924 – 78-pin Dsub female – 60 V
-
product
Micro Power, Header Insert, Receiver/ITA, SIM, Right Angle, 2 Pos, 2 Slot
510181103
This header insert contains 2 right-angle micropower contacts and is designed for soldering directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 2 of the 34 slots in this module.
-
product
High Speed End Launch Connectors
Fairview Microwave’s high-speed end launch connectors are comprised of four models that provide VSWR as low as 1.10:1 and a maximum operating frequency of 40 to 110 GHz, depending on the model. These end launch connectors are reusable, don’t require any soldering and have a compact profile with a 0.350-inch mounting width and a 0.005-inch launch pin. They feature an outer conductor made of stainless steel and a gold-plated beryllium copper center contact.
-
product
Circbord
8007
VECTOR Electronics and Technology, Inc.
Pad-Per-Hole pattern on component side. Overall Ground Plane pattern on wiring side.0.080” diameter isolated solder pad around holes oncomponent side. Plane surfaces solder coated for user convenience.
-
product
4-Pin Power D-Type Male Connector, 40A With Backshell
40-960-004-M
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
product
Precision Assemby & Production Solutions
Due to the continuing trend of product miniaturization with increased complexity, accurate gluing, welding, laser and assembly solutions are key for next-generation devices. As a result, the clear distinction between assembly and testing starts to blur. In smartphones, for example, testing and soldering the battery is one step in the production process. Hence, a combination of ultra-precise dosing, fixation, positioning and real-time feedback is essential to ensure best results and maximum reliability.
-
product
70 GHz Double Row Test Assembly
BE70A
The BE70A Series uses a single block design for ganged cabling and compression mount to the PCB, making it easier to install and eliminates soldering. The block consists of two rows, with up to 16 contacts, and is available for both microstrip and stripline transmission types. This proprietary cable design offers superior grounding (360-degree grounding with stripline) around a spring-loaded signal contact and provides a 1.85 mm connectors for RF device interfacing.
-
product
SolderStar Solutions
Solderstar provides a complete solution for soldering process control within the Electronics Manufacturing industry.
-
product
6U CompactPCI 9th Gen Intel Xeon®/Core™ Processor Blade with Two PMC/XMC Sites
cPCI-6540 Series
- 14nm multi-core 9th Gen Intel® Core™ processor (formerly Coffee Lake Refresh)- Dual channel DDR4 ECC memory, soldered and SO-CDIMM, up to 64GB- Versatile storage: SSD, CFast, M.2- Dual PMC/XMC sites- Remote management and TPM support
-
product
PCB Manufacturing
Printed circuit board assembly is the process of soldering or assembly of electronic components to a printed circuit board or PCB. Star Engineering is a full-service manufacturer of printed circuit board assemblies, providing complete solutions for all types of requirements. Being a skilled custom cable assembly manufacturer, our services include designing, testing, prototyping and manufacturing followed by complete support. We provide both surface mount (SMT assemblies) and through hole PCB apart from any custom requirements of your processes.
-
product
SparkFun Qwiic Single Relay
Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino or another low powered microcontroller? The SparkFun Qwiic Single Relay provides you with the easiest to use relay yet. The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!
-
product
37-Pin D-Type Female Solder Pin HV
40-960-037-F-HV
This connector is designed to allow users to directly terminate cables with soldered connections.
-
product
Plugbord
3677-3
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers. 3-Hole solder pads (0.28” x 0.080”) and buses forinterconnecting multiple component leads.No pattern on reverse side, edge contacts only Row and column legends provided.
-
product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Connector, D-Type 50-Pin Male With Crimp Pins
GT96108
Connector, D-type 50-pin male with solder pins.
