Solderability
-
Product
Nanotek Brush
Nanotek Series
-
Nanotek Brush is fine stainless wire brush for removing solders or dirt stuck on the tip of spring probe. It has its range of wire diameter from 30µ to 50µ and its fine wire is effective for removing solder or dirt on complicated tip type. We also have Nanotek vacuum, which is nanotech brush combined with vacuum cleaner powered by your compressor or vacuum pump.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
92-960-009-M-HV
D-Sub Male Connector
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - Without Backshell
-
Product
SparkFun GPS Breakout
Chip Antenna, SAM-M8Q (Qwiic)
-
The SparkFun SAM-M8Q GPS Breakout is a high quality GPS board with equally impressive configuration options. The SAM-M8Q is a 72-channel GNSS receiver, meaning it can receive signals from the GPS, GLONASS, and Galileo constellations. This increases precision and decreases lock time and thanks to the onboard rechargable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
37-Pin D-Type Male Solder Bucket
92-960-037-M
D-Sub Male Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Plugbord
3682-4
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. Interleaved buses pattern on wiring side, solder coated for user convenience. Overall ground plane with clearance around each hole on component side. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board. Row and column legends provided.
-
Product
26-Pin D-Type Connector Female
92-960-026-F
D-Sub Female Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
Eurocard Plugbord
E160-3U-3
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Overall ground plane both sides with 0.085" diameter clearance around each hole.. Solder coated for user convenience. Use T123 eyelets to simulate plated-thru holes committedto voltage or ground planes. Row and column legends provided.
-
Product
Circuit Card Assembly
-
Teledyne Advanced Electronic Solutions assembles and tests a variety of complex circuit card assemblies (CCAs) using leading edge, advanced technology assembly automation. We specialize in low-volume, high-mix assembly of highly complex CCAs.- RF, analog, high-speed and digital circuits on rigid-flex and Cu core substrates- Typical lot sizes from 3 to 300 pieces- 4 high speed, flexible SMT lines- Production processes for components from 0201 chips to large grid-array components and connectors- 100% solder paste, automated optical, and x-ray inspection- Forced air convection reflow with inert atmosphere option- Special processes for RF assemblies (filters, shields, etc)- BGA underfill, conformal coating, etc.- Selective and wave solder pin-thru-hole processes- CCA and component bonding processes
-
Product
Ethernet to Relay Minibox™
Model 8064
-
* Model 8064-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.*Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 8064s.* Optional terminal board and terminal strip for easy connections without soldering. See the Ethernet Accessory page.
-
Product
Replacement Solder Tip Leadset for Use with D410/D610
Dx10-SI-HiTEMP
-
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
Product
Serial to Relay Interface Boards
Model 2364 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
Product
Plugbord
4112
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. Zig-Zag Bus Pattern on wiring side. Zig-Zag Bus Pattern provides access to voltage or ground at alternating hole positions. Continuous ground plane on component side with 0.085” etched clearance area around each hole Row and column legends provided
-
Product
20-Pin GMCT Female Connector, 10A, With Backshell
40-960-020-10A-F
GMCT Female Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. Also included is the backshell with screwlocks and cable clamp.
-
Product
5D SPI
-
On Mek Solder Paset Inspection systems, items which are better inspected in 2D, such as area offset and bridging, are viewed in full colour. Using colour inspection the ISO-Spector S2 SPI can tell the difference between paste, solder mask, silk screen and other PCB features and the SPI system can intelligently give you accurate results. Volume and height measurement in 3D are combined with the 2D inspection in Real-time, to give a True colour 3D image. Other 3D SPI systems only inspect in the 3rd dimension, (Z axis) and make extrapolated assumptions about the 2D image.
-
Product
In System Programmers
-
In-circuit serial programming, also known as in-system programming (ISP) or in-circuit programming (ICP) enables programming and reprogramming of microcontrollers, serial EEPROMs and flash memories already soldered on a target PCB.
-
Product
Current Sense Resistors
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers a wide variety of Thick Film Current Sense Resistors (ERJ-B1, B2, xB, xBW, xCW) in a large range of case sizes and in wide terminal types for high solder joint reliability. The ERJ Series of Current Sense Resistors offers power ratings up to 2W with low ohmic ratings ranging from 5mΩ to 10Ω. Panasonic’s Thick Film Current Sense Resistor portfolio offers a more cost effective option with high reliability. Panasonic has a wide line of case size options ranging from 0402 to 2512 in conventional terminal and 0612 to 1020 for wide terminal.
-
Product
Testing & Measurement Services
-
Delserro Engineering Solutions
Delserro Engineering Solutions is your complete source forHALT/HASS, Accelerated Life Testing, Environmental Testing, Lead Free Solder Joint Reliability Testing, Linear andNon-Linear FEA, Computational Fluid Dynamics (CFD)
-
Product
Hard Metric Eurocard Plugbord
8018
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector.Pad-Per-Hole both sides.Combination Pattern: Half 2mm grid and other half 0.1” grid. Pad and bus surfaces solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
Product
PCBA & Bare Board Cleanliness Tester
Zero-Ion G3
-
For two decades, thousands of electronics assemblers have relied on the Zero-Ion cleanliness testing to verify the cleanliness of post-reflow printed circuit assemblies and bare boards. Over time, as PCB assemblies have become more complex and more densely populated with surface mount components, and as vigorous quality standards such as ISO, TQM and Six Sigma have become commonplace, the ability to meet—and confirm—cleanliness levels has grown in importance. The Zero-Ion ROSE tester has kept pace with customer requirements, and the Zero-Ion G3 is the most advanced Zero-Ion ever designed, capable of testing assemblies reflowed with any solder paste, including no clean—yet its also one of the most affordable cleanliness testers on the market as well, with performance and ease of use second to none.
-
Product
SparkFun GPS Breakout
NEO-M9N, SMA (Qwiic)
-
The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options including SMA. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions increasing, precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which makes it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
50-Pin D-Type Connector, Female
40-960-050-F
D-Sub Female Connector
This connector is designed to allow users to directly terminate cables with soldered connections.
-
Product
6U Processor Blade
CP62007
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62007 is a 6U processor blade based on Intel’s 4th generation core i7/i5 processors using 22nm process technology, supporting up to four cores / eight threads at 2.4GHz. CP62007 supports up to 16GB onboard soldered low voltage DRAM with ECC. It also offers up to 64/128GB SLC/MLC onboard SATA SSD for installing operating system and drivers. The onboard design of memory and SSD enhance the anti-shock and vibration performance dramatically.CP62007’s onboard processor integrates Intel® HD Graphics 4600 controller, supporting a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA. And the VGA resolution is up to 2048x1536. With HDMI/DP/eDP outputs, the resolution can be up to “4K”.CP62007 supports 1x VGA and 2x DP/HDMI/DVI, up to 3 independent or cloned displays.CP62007 uses high speed CPCI connectors on J3 and J4 position for transferring high speed serial signals, such as PCIe2.0, USB3.0 and SATAIII. And the foot-print of high speed connectors are fully compliant with CompactPCI specifications.
-
Product
MCX Connectors
-
Pasternack MCX connector category includes dozens of part numbers, most of which are RoHS and REACH compliant. MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our MCX connectors are built to precise RF and microwave industry specifications. MCX connector items are built in jack or plug gender in standard polarity or reverse polarity threads, with 50 Ohm impedance. Connectors in the MCX series are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These MCX connector designs include crimp/solder or solder attachment methods. We offer MCX connectors with standard or high performance levels built with brass or stainless steel bodies. As with our other over 40,000 RF. microwave and millimeter wave products at Pasternack, this MCX connector series is in-stock. Not only in stock, but these coaxial connectors will ship the same day as they are purchased.
-
Product
SMC Connectors
-
Pasternack SMC connector category has dozens part numbers, most of which are RoHS and REACH compliant. SMC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These SMC connectors are built to precise RF and microwave industry specifications. Pasternack connectors with SMC series are built in jack or plug gender with 50 Ohm impedance. SMC connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMC connector designs include clamp/solder, crimp/solder or solder attachment methods. as with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMC connector series is in-stock. In addition to being in stock, these connectors will ship the same-day as purchased.
-
Product
Eurocard Plugbord
E160-3U-1
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides. Pad and bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
Product
SparkFun High Precision Temperature Sensor
TMP117 (Qwiic)
-
The SparkFun Qwiic TMP117 breakout is a high precision temperature sensor equipped with an I2C interface. It outputs temperature readings with high precision of ±0.1°C across the temperature range of -20°C to +50°Cs with no calibration and a maximum range from -55°C to 150°C. The SparkFun High Precision Temperature Sensor also has a very low power consumption rate which minimizes the impact of self-heating on measurement accuracy. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
Plugbord
3795-1
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.100"(2.54mm) centers. 3-Hole Solder Pads One Side Only. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. All pad and bus surfaces solder coated for user convenience. No pattern on reverse side, edge contacts only. Convenient easy-to-read hole marking legend on wiring side.
-
Product
44-Pin D-Type Connector, Female
92-960-044-F
D-Sub Female Connector
This connector is designed to allow users to directly terminate cables with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
200-Pin LFH Cable Connector, Male
40-961A-200-M
LFH Male Connector
This connector is designed to allow users to directly terminate with soldered connections to the 200 pin LFH connector.
-
Product
Digital Low Resistance Tester
TH2512
-
Shenzhen Chuangxin Instruments Co., Ltd.
The TH2512 series digital dc low resistance tester i s an intelligent, wide range, high-precision tester which suitable for transformer, inductor copper resistance, relay contact resistance, switches, connectors, wire resistance, contact resistance component solder contact resistance, PCB line, welding hole resistance and metal detection, etc. It’s applied to the production line and can use HANDLER interface and GPIB interface (option) output good/bad signal, in order to improve production line automation testing capability.
