Product

1' Harness, 50-Pin Male D-Sub Connector on one end, loose wired (numbered) other end

GT97106

-

Marvin Test Solutions, Inc.

GT97106 - Marvin Test Solutions, Inc.

1' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.

Product

High Precision Glow Wire Tester

CX-Z17

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-Z17 - Shenzhen Chuangxin Instruments Co., Ltd.

IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is desinged according to IEC60695-2-1, IEC60695-2-13, UL746A, IEC829, DIN695 and VDE0471 etc. standards.The IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances.

Product

Cables, Harnesses & Wiring Looms

-

AmFax Ltd

AmFax Ltd

​Amfax manufacture a wide range of wiring harness solutions in a variety of styles and finishes. These wiring harnesses, or looms as they are often called, can be constructed using heat-shrink, conduit tube, braid, tape, tie-wraps or lacing cord.

Product

15 Ft Cable, 78-Pin Female Connector On One End, Loose Wired (Numbered) Other End

GT97113

-

Marvin Test Solutions, Inc.

GT97113 - Marvin Test Solutions, Inc.

15' harness, 78-pin female D-sub connector on one end, loose wired (numbered) other end.

Product

One Wire Communication Board

MS 1727

-

Meltronics Systemtech

MS 1727 - Meltronics Systemtech

- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.

Product

Bulk Wire and Cable

-

Teledyne Marine Cable Solutions

Teledyne Marine Cable Solutions

With 50 years of dedicated experience in providing cable and interconnect solutions, Teledyne Cable Solutions meets challenges for application-specific, multi-core cables for harsh environments and complex ruggedized cable assemblies and harnesses.​

Product

Wire Damage Test Device For Pull Testing

IEC60884 FIG11

-

Shenzhen Chuangxin Instruments Co., Ltd.

IEC60884 FIG11 - Shenzhen Chuangxin Instruments Co., Ltd.

IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.

Product

Gauge Type T Thermocouple Wire

W-TW-36P2

-

Physitemp Instruments

W-TW-36P2 - Physitemp Instruments

Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.

Product

Automatic High Voltage Wire Harness Testers

-

MK Test Systems Ltd.

MK Test Systems Ltd.

Automatic high voltage wire harness testers are used in a variety of industries, such as aerospace and defence through to rail, and are used to test any equipment which contains a high number of electrical wires, or active components ensuring these pass specified test criteria at the sub-assembly and final stages of construction. These systems ensure the wiring and components are 100% compliant and undamaged, recording every test measurement and aiding diagnosis of detected faults.

Product

Corona Resistant Tester of Enamelled Wire

DPT-1000S

-

Shanghai Dean Electrical Co., Ltd

DPT-1000S - Shanghai Dean Electrical Co., Ltd

·The tester is comply with the requirements of standards GB/T 1707-2008, GB/T 24122-2009, GB14711-2013, meet the requirement of standard JB/T 10930-2010;·Multiple samples can be tested at same time;·Used for testing the feature of high frequency pulse resistance (performance of Corona-resistance).

Product

Fault Finder for Electrical Wiring Open / Short Circuit

FF310

-

General Technologies Corp.

FF310 - General Technologies Corp.

42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.

Product

3 Wire (Digital) Earth Resistance Tester

4120 ER

-

Standard Electric Works Co., Ltd

4120 ER - Standard Electric Works Co., Ltd

● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.

Product

Wire Crimp Testers

-

IMADA, Incorporated

IMADA, Incorporated

Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.

Product

Non-Contact Voltage Tester With Wire Stripper

5227

-

Peaceful Thriving Enterprise Co Ltd

5227 - Peaceful Thriving Enterprise Co Ltd

This product combines most required tools for an electrician to do the wiring job within the building, which includes screwdriver, non-contact voltage detector, illumination and wire stripper for most type wires.

Product

IEC60695-11-2 Single Wire And Cable Vertical Burning Tester

CX-D12

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-D12 - Shenzhen Chuangxin Instruments Co., Ltd.

It’s strictly designed according to IEC60695-11-2, IEC60332-1, GB/T18380.11-2008, GB/T18380.12-2008 etc. Stainless steel screen with a sliding burner handle support for approaching or movingback the flame from the sample under test according to the CEI standards for test on cables.

Product

3'Harness, 50-Pin Male D-sub Connector on one end, loose wired (numbered) other end

GT97107

-

Marvin Test Solutions, Inc.

GT97107 - Marvin Test Solutions, Inc.

3' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.

Product

Pilot Wire

-

Mors Smitt Group

Mors Smitt Group

The concept is based on the need to improve the performance of existing pilot wire protection schemes by increasing reliability & availability as well as adding an over current guard function. This can be achieved at considerably lower cost than the replacement of the existing proven protection relays & change over to a fibre optic communication channel.

Product

50-Pin DIN-Rail Flat Cable Wiring Board

ADAM-3950

-

Advantech Co. Ltd.

ADAM-3950 - Advantech Co. Ltd.

Low cost universal DIN-rail mounting screw terminal module for PC-LabCard™ products with 50-pin flat cable connectorCase dimensions (W x L x H): 77.5 x 146.3 x 51 mm (3.1" x 5.8" x 2.0")To Be Used With USB-4751/L, PCI-1737U, PCI-1739U, PCL-722, PCL-724, PCL-731

Product

3 Ft Harness, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End

GT97102

-

Marvin Test Solutions, Inc.

GT97102 - Marvin Test Solutions, Inc.

3' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.

Product

Wire Crimp Pull Tester (Motorized)

WT3-201M

-

Mark-10 Corp.

WT3-201M - Mark-10 Corp.

The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.

Product

100-Pin Micro-D Connector, Male, Discrete Wire, 2-56 UNC Screwlocks, Metal Shell

C100SMR-1CW-6A

-

Pickering Interfaces Inc.

C100SMR-1CW-6A - Pickering Interfaces Inc.

This accessory is designed to allow users to directly terminate a cable to the connector. It is difficult to terminate cable to the 100-Pin SCSI Style Micro-D connector because of the high density and fine pitch. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.