Wire Trackers
Identify a wire's path.
-
Product
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP Wire H-MTD Cable Jack, 1 Position
7-142716765-036
VTAC Patchcord
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Position.
-
Product
100-Pin DIN-Rail SCSI Wiring Board
ADAM-39100
-
Low cost universal DIN-rail mounting screw terminal module for industrial applications with 100-pin SCSI female connectorDimensions (W x L x H): 80 x 230 x 42 mm (3.14" x 9.05" x 1.65")
-
Product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Twin Female Contacts & Square Posts for Wire Wrap (p/n's 610138200 & 610138118)
510150136
Receiver Module
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
Product
3 ft Coax Wire with a Coax Pin
GX96411
-
One 3 ft Coax Wire with a Coax Pin Crimped on One EndRequires the GX96409 connector housing.
-
Product
QuadraPaddle Signal Insert, ITA, SIM, 4 Position (not Loaded- For Discrete Wiring Only)
510181101
SIM Insert
QuadraPaddle Signal Insert, ITA, SIM, 4 Position (not loaded- for discrete wiring only)
-
Product
15' Cable, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97112
-
15' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
Platinum RTD Sensor - PT100 - 3 Wire 1 meter long
-
For precision temperature sensing, nothing beats a Platinum RTD. Resistance temperature detectors (RTDs) are temperature sensors that contain a resistor that changes resistance value as its temperature changes, basically a kind of thermistor. In this sensor, the resistor is actually a small strip of Platinum with a resistance of 100 ohms at 0C, thus the name PT100. Compared to most NTC/PTC thermistors, the PT type of RTD is much most stable and precise (but also more expensive) PT100's have been used for many years to measure temperature in laboratory and industrial processes, and have developed a reputation for accuracy (better than thermocouples), repeatability, and stability.
-
Product
Drawing Die And Wire Measurement
DGMS – Die Geometry Measuring System
-
Optik Elektronik Gerätetechnik GmbH
Measuring system for diameter, roundness, reduction angle and bearing length of wire drawing dies.
-
Product
9050, 50 Module, Receiver, VXI and Discrete Wiring, Double Tier
310104248
Receiver
This 50 module receiver is rugged and designed to accommodate high I/O. With high contact point availability, the 9050 receiver is suited for larger test and measurement systems. The top tier accommodates VXI instruments and accepts VPC's interconnect adapters with the bottom tier for discrete wiring.
-
Product
Bespoke Wire Rope Solutions
-
Wire ropes with customized end fitting, or MS Standard Wire Ropes.
-
Product
Gauge Type T Thermocouple Wire
W-TW-26
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
High Altitude Wiring Clamp
-
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
Product
Signal, Module, ID, CASS, 64 Position, Discrete Wiring
510114108
ITA Module
Signal, Module, ID, CASS, 64 Position, Discrete Wiring.
-
Product
Sediment Tracker™
-
Track the settling location of sediment caused by stormwater runoff. The Sediment Tracker's™ high-drag drogue lowers at a controlled rate approximating sediment falling to the ocean floor.
-
Product
Signal Module, ITA, QuadraPaddle, 480 Position, Fully Loaded For Wire Wrap With Anti-Rotation (610 138 122)
510151127
ITA Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
