- LBA Group, Inc
product
MW AM Broadcast Mobile Antenna System
TUP-3
The TUP-3 system is capable of transmitting efficiently at carrier frequencies from below 1000 kHz to over 1700 kHz. It is rated for power to 5000 watts, 125 percent modulated. Housed is a weatherproof cabinet, the integral tuning unit features high quality electronic components and matches the TUP-3 system to a 50 ohm transmission line. The self-supporting design of the tower also minimizes erection time and complexity.
-
product
Advanced Test Platform
980 12G
The Teledyne LeCroy quantumdata 980 12G-SDI Video Generator / Analyzer module supports video and audio functional testing of next gen broadcast monitors, conversion devices and sources up to 12G-SDI. The module is equipped with four (4)12G-SDI-capable output ports. The output ports can be aggregated for Dual link HD-SDI and Quad link 3G-SDI operation. A genlock input supporting both SD analog black burst and HD tri-level to sync the output clocks with a "house sync" but the module can also run o...show more -
product
Analog DVR
Sylo Vision Technology Co., Limited
Security cameras capture an analog video signal and transfer that signal over coax cable to the Digital Video Recorder (DVR). Each camera may be powered by plugging in the power supply right at the camera or by using RG59 Siamese cable which bundles the video and the power cables. The DVR converts the analog signal to digital, compresses it, and then stores it on a hard drive for later retrieval. Intelligence is built into the DVR to handle such things as scheduling, motion detection, and digita...show more -
product
Test Card Generator
TCG1
This generator provides a standard 75O, 1-volt p-p; PAL encoded CCIR video signal for the testing of monitors and other CCTV equipment. The Test Card Generator TGC1 may display one of four test patterns , (i) Colour bars with reference, (ii) Red Raster, (iii) Peak White Raster and (iv) Composite Test Card (see picture below). The Test Card Pattern incorporates many of the attributes of broadcast test patterns for the evaluation and setting up of CCTV video equipment.
-
product
Broadcast Components
Cable testing sections may be used to isolate the antenna inputs from the main feeder when testing either the antenna or feeder. These devices are normally installed between the main feeder cable and antenna inputconnector and allow access to the antenna input without the need to remove the main feeder cable. Cable test sections are particularly useful with large feeder cables that are difficult to manoeuvre.
-
product
Broadcast Analyzers
Our product portfolio offers dedicated instruments for various terrestrial and cable TV and radio standards. For satellite applications, special options are available for our spectrum analyzers.
-
product
Real-Time Broadcast Analysis
Mediaproxy provides a comprehensive suite of software-based analysis applications to help you attend to on-air issues quickly and resolve them efficiently. Employing the latest user interface technologies, complex analysis tasks are made easy and seamless, including your mobile devices.
-
product
Broadcast Video Products
Macom Technology Solutions Holdings Inc.
Macom Broadcast Video Products
-
product
Monitors
Whether you need a local display, alarm and shutdown capability, data recording, and the ability to communicate using Modbus over Ethernet TCP/IP; or you need to trend waveform and transient data to provide a predictive look at your machine’s condition, Metrix has a solution to meet your machinery monitoring requirements.
-
product
Waveform Monitors
LV5350
The LV5350 waveform monitor offers a 7-inch HD screen display in a compact 3 x ½ RU package that can operate on AC or DC. Waveform, vector and picture with 4K 12G-SDI and audio options . Easy menu operation with touch screen, mouse, and front panel button controls.
-
product
Vibration Monitors
VS1 / VS2
Features • VS1 protects against excessive vibration levels • VS2 is ideal for use deliberately vibrating machinery • Settable RMS vibration velocity alarm trip-point and delay time • LED’s provide an instant view of machine status • Isolated SPDT relay output or transistor output • 24 VDC (18-30 VDC) powered
-
product
Monitors
Off-air monitoring and + demod/metering equipment for AMFMHD-Radio DBA+ Internet Radio.
-
product
Transformer Monitors
The Transformer Advantage is a precision temperature monitor for liquid-immersed power and distribution transformers. It is rugged, fully electronic and field configurable. With Transformer Advantage, users can extend transformer life, utilize maximum capacity and reduce maintenance costs.
-
product
Audio Monitors
In an ideal world, the human ear would be the best instrument any of us could use for quality control and impartial judgment of your daily work. However, it is just not that simple. The introduction of HD and surround sound, as well as loudness control issues have triggered an increasing demand for quality control and monitoring of audio signals. Fast perception and accurate assessment of audio levels using visual representation methods are indispensable elements of daily work. RTW's easy-to-use Audio Monitors are the obvious choice.
-
product
Phase Monitors
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
product
High-Power Stage Monitors
MJF
Between the small footprint of the MJF-208 or the balanced but potent output of the MJF-210, your stage monitor requirements are covered.
-
product
Power Monitors
NAI''s Power Monitors are used to monitor voltage, frequency, phase characteristics, or phase rotation of single- and three-phase power lines. Specifically designed for rugged defense and industrial applications, these Power Monitors meet the most stringent performance and environmental requirements.
-
product
Impedance Monitors
Single channel impedance monitorA flexible frequency generator/analyzerSupporting external load/potentiostat - TDI Dynaload RBL488 series & XBL series - WonATech WEL Load - Other 3rd parties potentiostat/galvanostat
-
product
Cryogenic Temperature Monitors
Monitor temperatures from 1.4K to over 800K. Choose from one or eight standard inputs. USB, IEEE-488, and RS-232C interfaces, relays, and analog outputs are available.
-
product
SpaceWire Monitors
This section details the 4Links range of high-performance test equipment that is used to monitor SpaceWire networks. These devices are attached to your SpaceWire systems and then can be accessed via Gigabit Ethernet, using the standard TCP/IP family of protocols, so that they can be controlled remotely (for instance, by partners collaborating on a mission).
-
product
Transmitter Monitors Carbon Monoxide
CO-R
The CO transmitter monitors carbon monoxide (CO) levels and is designed for the continuous monitoring of vehicle exhaust in non-hazardous areas. The CO uses a wide spectrum, long life electrochemical sensor to measure the amount of carbon monoxide in the environment. It is offered with an operating range of 0 to 125 ppm. Both the Room and Duct CO transmitters are offered in a standard NEMA 1 rated ABS Polycarbonate plastic enclosure. An optional NEMA 4X watertight and dust proof enclosure is only available with the CO room transmitter.
-
product
RF Power Monitors
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
product
Heat Stress Monitors
Heat stress management is often viewed as time-consuming and complex. Simplify your heat stress management with TSI’s intuitive QUESTemp° Series Heat Stress Monitors.
-
product
The Nortech Fiber Optic Monitors
The fiber optic signal conditioners are designed for direct, accurate and real-time temperature monitoring to manage and maximize your transformer’s performance. The Nortech temperature monitor family comes in three different classes: the EasyGrid is the most comprehensive model, the EasyGrid LT is a compact and very cost-effective model for low channel count monitoring applications, and the EasyGrid Base is and even more compact model designed for easy network integration.
-
product
Power Monitors
The Monitor family includes a range of products that not only measure power and VSWR but also provide hard contact alarms to protect your system in the event of a system failure – the IP-enabled, BPME is even capable of emailing a failure notification.
-
product
Temperature Monitors
SIM923A
Stanford Research Systems, Inc.
The SIM923A has selectable 10 µA and 1 mA current sources to provide sensor excitation. Sensor resistance is determined ratiometrically with a half-bridge circuit consisting of the sensor and an internal reference resistor.
-
product
Indoor Air Quality Monitors
Maintaining proper indoor air quality (IAQ) has only become more important in recent years as personal health and comfort have become a higher priority than ever before. Our testing and monitoring instruments for IAQ, including our indoor air quality monitors, gas monitor, and odor meters help industrial hygiene and HVAC professionals test and monitor environments to solve crucial air quality problems.
-
product
Industrial Touch Monitors
With the latest touchscreen technology, our industrial monitors are designed to streamline and automate daily operations, enhancing operational efficiency. These monitors provide smooth user interaction, an unbeatable visual experience, and durability that meet various industrial applications’ demands. ADLINK's open-frame and true-flat industrial touch monitors offer superior quality, making them ideal Human Machine Interface (HMI) applications in industries like manufacturing, public transport, hospitality, and retail where smooth user interaction is essential.
-
product
Surface Quality Monitors
PET manufactures and markets non-destructive, non-contact surface contamination and thin film detection models and automated systems (surface quality monitoring system) capable of detecting thin layer contamination, thin films and coating down to the Angstrom level. These systems represent a major breakthrough by providing, for the first time, a quantitative measure of surface cleanliness. As surface cleanliness verification instruments, in a part cleaning environment, these products are capable...show more