Wind Tunnels
deliver specific air-stream to characterize air-flow's affect.
See Also: Wind, Tunnel, Anemometers, Wind Turbine, Wind Speed
-
-
Product
Wind Tunnels
-
Omega's Wind Tunnels come in benchtop or floor standing models for any research, manufacturing, or quality control application. All Wind Tunnels are manufactured in The USA.
-
Product
Micromanometers
-
The DPM range of handheld auto-zeroing Micromanometers are renowned in the HVAC, aerodynamics, clean room, wind tunnel, COSHH, LEV sectors and in other industries where low pressure measurements are critical.
-
Product
Wind Sensor
FT722
-
Specifically designed for wind turbine control, the FT722 reads wind speeds from 0-50m/s. Its inovative design incorperates a series of "turbulators" (patient pending) which condition the air flow. With updated software, and calibration in our new state-of-the-art wind tunnel, the FT722 delivers our highest levels of accuracy in wind speed, wind direction and accoustic temperature measurement.
-
Product
Wind Tunnel Balances
-
To meet the increasing demands of a modern wind tunnel and the need for appropriate simulation, HORIBA has developed the rolling road and wheel spinning units for road simulation. To increase the wind tunnel efficiency, the HORIBA wind tunnel balances can be equipped with lifting platforms which enable vehicle modifications to be performed in a short time
-
Product
Ruggedized Ethernet Data Acquisition Systems
Series 7000
-
The Series 7000 Ruggedized Ethernet DAS brings new capabilities and levels of performance to transducer data acquisition. The ruggedized system is designed for installation in wind tunnels, engine test stands and other facilities where it is desired to locate the DAS on or near the test article, reducing installation and cable costs while improving signal quality and reliability. Each unit is a network appliance which conditions, amplifies and digitizes outputs from transducers. Multiple units are easily combined and distributable for larger installations. Real-time temperature Compensation of gain offset and Excitation Voltage, quality signal conditioning with high gain and a 24-Bit A/D per channel provide a high accuracy and high resolution DAS that will perform across a wide operating range.
-
Product
Wind Tunnel Control System
WTCS
-
Wind tunnel facilities are important for the development of all kinds of transportation vehicles. In any kind of wind tunnel - aerodynamic, climatic or acoustic - users are interested in optimization of the valuable factor time for the performance of experiments and measurements. Aerodynamic properties exerting direct influence to fuel consumption have to be optimized.
-
Product
Semiconductor Package Wind Tunnel
WT-100
-
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
Product
Aerospace Testing Solutions
-
Aerospace Testing SolutionsDewesoft offers a variety of solutions for aerospace testing. From standard data recording, structural dynamics, rotating machinery analysis, acoustic testing, to more specific applications like ground station telemetry solutions with full support for ARINC-429 and MIL-STD-1553 buses, PCM telemetry, IRIG 106 - Chapter 10, Ethernet packets, and iNet telemetry.We can provide flexible and robust data acquisition hardware and software that will match your requirement for testing airplanes, helicopters, rockets, satellites in the air, space, or on the ground - proving ground, wind tunnel, vibration shaker or acoustic chamber. Our solutions are being used and trusted by leading aerospace companies on the most demanding projects like NASA, ESA, Space X, Airbus, Boeing, Lockheed Martin, Bombardier, Honeywell to name just a few.
-
-
Product
Winding Resistance Meter
TRM 50+
-
SCOPE introduces 50 A state of the art precision winding resistance meter, specially designed for field testing as well as factory testing of large transformers up to 500 MVA. Winding resistance value of transformer and rotating machine are directly displayed on 5.7” TFT display. TRM 50 is designed to work in live EHV switchyard conditions, ensuring operator’s safety and repeatability of results. Maintenance time saving is ensured by one time connection to transformer with simultaneous resistance measurement of three / six windings, measurement of resistances of all taps with automated tap change and demagnetization facility. The meter is protected against the back-EMF offered by large inductive windings.
-
Product
Wind Power Solution
NXA GAMESA
-
The NXA GAMESA is custom-made with firmware and fixtures designed specifically for Gamesa turbines: G80x, G90x, G114, G126, G132, G145. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Winding Resistance Test
20A DC booster
-
The 20A DC STCS booster allows to perform resistance tests on a PT with a current up to 20 A DC. The option is used together with STS 5000 and STS 4000 and must be connected to STCS module.
-
Product
Motor Winding Ohmmeter
RMO-M Series
-
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement
-
Product
Wind Power Solution
ECO GE
-
The ECO GE is custom-made with firmware and fixtures designed specifically for GE 1.5x and 2.5x. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Wind Meters
-
According to the type of application, wind meters are made as hot wire wind-meters or pocket weather wind-meters, all of these wind-meters can measure air velocity and air pressure. Wind meters for the measurement of air velocity and air pressure. The measurement results can be stored in memory of the device (depending on the model). There are a lot of different instruments available in our stores. These wind meters are ideal for taking quick or constant measurements. Wind meters for measuring air velocity and volume flow are available here. The pocket-sized wind meters are implemented as hot-wire wind meters, vane wind meters, cup wind meters or portable, waterproof wind meters depending on the particular application.
-
Product
Winding Resistance Meter
-
* Selectable four resistance ranges.* 4 1/2 digits LED display* High measurement Current (10A)* True four Technique elimanates lead resistance errors Systems* Fully protected against overloads* Proven design* Computer connectivity through RS 232
-
Product
Transformer Winding Resistance Meters
-
Vanguard Instruments Company, Inc.
The TRM-40 is Vanguard Instruments’ third generation transformer winding resistance meter. The TRM-40 is designed specifically to measure DC resistance values of transformer windings, rotating machine windings, or any dc resistance of an inductive device.
-
Product
Automatic Winding Turns Tester
-
This tester has the advantage of high accuracy and efficiency, limited influence due to the form and size of the coil to be analyzed, and fast & easy operation thanks to the precision sensor and microprocessor that adopt the patent know-how developed by the manufacture. This tester, when in operation, does not need any further adjustment and calibration. Just connecting the clip leads to each terminal lug of the coil winding, then the tester instantly shows the exact number of the winding turns on the digital display. Unlike other similar devices, input the data of standard coil to test against is unnecessary. In this way, this tester greatly upgrades the inspection and analyzing efficiency.
-
Product
IMPULSE SURGE WINDING TESTER
VE2882A-5U
-
Impulse Tester can detect turn & layer short ,the differences in the number of turns and the material of the core. If high impulse voltage is applied, the poor insulation will appear as a corona or layer discharge.
-
Product
TRANSFORMER WINDING RESISTANCE METER
-
International Biological Laboratories
This Test set is suitable to measure winding resistance of transformers, single or 3-phase, star or delta connected upto several MVA.Two independent displays read the resistance of both primary & secondary windings simultaneously. However, primary or secondary winding can also be measured separately.
-
Product
Transformer Winding Resistance Meters
RMO TW Series
-
The RMO-TW instrument can perform a simple, fast and reliable verification of a transformer on-load tap changer. This instrument allows measurements of a winding resistance at each tapping position of an on-load tap changer without discharging between tests. Problems with OLTC switching, such as interruption, can be detected with these measurements. The results are displayed on a backlit LCD screen.
-
Product
Scanning Tunneling Microscope for Ultra High Vacuum
STM
-
A.P.E. Research instrument is a versatile Scanning Tunneling Microscope, STM, capable of scanning samples of almost any size. It can operate in UHV and in air. The systems have been designed to evaporate (e.g. metals, organic molecules) in UHV directly onthe sample mounted on the STM head.
-
Product
Transformer Winding Resistance Meter
10A
-
*10A DC continuous current in 4 ranges of 0.01A, 0.1A, 1A and 10A.*4 ½ digit display for higher resolution.*Dual channel measurement.*Suitable for operation in energized switchyard conditions.*Specialized protection circuits for suppression of inductive voltage kickback.*SMPS based - lightweight and portable.
-
Product
Wind Power Solution
EVO ACCIONA
-
The EVO ACCIONA is custom-made with firmware and fixtures designed specifically for Acciona turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Transformer Winding Resistance Tester
KRI 9310
-
KRI 9310 adopt Kelvin four-wire testing method, which effectively eliminates the influence of the resistance of the test line on the test results. It can be able to increases the current to 10A by which can test extremely low resistance to 0.01 Ω(such as amorphous alloy, Copper-nickel, nickel-chromium-iron, iron-chromium-aluminum etc). For the tested objects with high resistance value (CT/PT), the instrument can extend the range to 20 kΩ，so the wide resistance test range enables KRI9310 can cover 80% of the power transformer products on the market and switchgear bus-bar cable etc. The power of the tester use the built-in rechargeable lithium battery that can test hundreds of transformers by one time charging.
-
Product
Tunnel Demagnetizing Unit
DM-T
-
Tunnel units are particularly suited to demagnetising parts with large surface areas and thin walls, for example, tubes, rods, etc.
-
Product
Winding Resistance Meters
-
The NMC 'TDR' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. 'TDR' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. 'TDR' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.
-
Product
Duct Type Wind Speed Sensor
WSA
-
Due to environmental quality management and energy management, we've developed WSA, wind speed sensors which can be applied on ventilation systems, air conditioning, and negative pressure rooms. WSA is a high-accuracy duct type wind speed sensor which can quickly measure the small wind speed. It is stable, high-accurate, and with small drift only. Also, it can caculate the value of the current air volume depending on the measured cross-sectional area of the ducting. Ducting installation and screwless terminals help the users work more easily. Besides, the sensor is equipped with EMC anti-interference devices so that it can withstand strong electromagnetic interferences.
-
Product
Wind Sensors
FT742
-
The FT742 measures wind speeds up to 75 m/s. Its innovative design incorporates a series of “turbulators” which condition the air flow to deliver our highest levels of accuracy yet. Available in four mounting options, the Flat Front (FF) and Pipe Mount (PM) are typically used in wind turbine control and the Direct Mount (DM) in meteorological applications. The Surface Mount (SM) has been specifically designed for OEM integration and for use on UAVs/drones.
