-
product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1L18-6-S
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1T1-6-S
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Ultra High 6.70 (190.00) - 11.80 (335.00) General Purpose Probe
EPA-4E-2
Current Rating (Amps): 7Average Probe Resistance (mOhm): 35Test Center (mil): 187Test Center (mm): 4.75Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 1,320Overall Length (mm): 33.53
-
product
Standard 1.68 (48.00) - 3.20 (91.00) General Purpose Probe
HPA-52T
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 75Full Travel (mm): 1.91Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 250,000Overall Length (mil): 629Overall Length (mm): 15.98
-
product
DH Series Solder-In Tip, 30 GHz BW, 3.5 Vpp Range
DH-SI
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Test Contactor/Probe Head
Atlas
QuadTech™ probe solution with cruciform tip strength that stands up to lateral force without bending, plus an enhanced compliance window to accommodate package stack height tolerance.Atlas™ test contactor offers electrical performance that allows the customer to test to the true performance of the device. Atlas WLCSP test contactors achieve mechanical reliability with a rigid “cruciform” tip applied to Cohu’s QuadTech flat probe technology. The Atlas offers a short electrical path, with lower capacitance and inductance, that is ideal for functional and AC parametric testing of WLCSP devices that require high system bandwidth and throughput gains in large multisite test applications.
-
product
Professional Imaging Moisture Kit
MR160-KIT5
The FLIR MR160-KIT5 has all the tools you need to quickly locate and diagnose moisture issues. Featuring Infrared Guided Measurement (IGM™), the MR160 visually guides you to the problem so you can confidently take measurements and analyze readings. An integrated pinless sensor and an external pin probe provide the flexibility to take either intrusive or non-intrusive measurements. The kit also includes a hammer/wall cavity probe combo for additional measurement applications.
-
product
High Impedance Active Probes
7A
An unterminated version, can be used for capacitance and resistance measurements or in low to medium speed signal applications where a 50 ohm termination is not required. A flexible coaxial cable length of 6 feet in length is standard on the Model 7A; however, when used for capacitance measurements, GGB Industries, Inc., recommends using a shorter 3 foot cable. If a shorter length of cable is desired for capacitance measurements, please specify it when ordering (Model 7A-3ft.). Please note that Model 7A uses Model 7 replacement tips.
-
product
Redox Meters
At PCE Instruments you will find redox meter for measures redox potential in laboratories, industry and in the environment. Our redox meters are easy to use instruments to measure oxidation-reduction potential of a solution according to the customers requirements. Some redox meters are also able to measure pH, conductivity and temperature.Here you will find an explanation about the Redox potential. In our offer you will find diverse redox meters, such as redox handle meters, redox meters with an external probe as well as tabletop redox meters for data to be transferred to a computer.
-
product
200 MHz, 3.5 pF, 1 M Active Differential Probe, ±20 V
T3LVD20-200
200 MHz, 3.5 pF, 1 M Active Differential Probe, ±20 V.
-
product
High 2.84 (81.00) - 8.00 (227.00) High Performance Lead Free Probe
LFRE-25UN-8
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Bias Ball Probe
POGO-1B-2
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Bias Ball Probe
POGO-1L18-2
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
MPI Manual Probe Systems
MPI Advanced Semiconductor Test
manual probe systems are open, easy to use and cost effective yet highly accurate. These systems are designed for precision analysis of substrates and wafers up to 150, 200 and 300mm.
-
product
Portable Emission Analyzers
Portable Emission Analyzers are especially useful for, auto repairs, inspections, safety checks, and general engine tuning. Simply insert a probe into the exhaust pipe and press a key to initiate measurements. Readings appear on a back-lit liquid-crystal display on the front of the analyzer.
-
product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Lead Free Probe
LFRE-1L18-10
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Ultra High 3.83 (109.00) - 10.00 (283.00) High Performance Lead Free Probe
LFRE-72H-10
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,700Overall Length (mm): 43.18
-
product
Probe Cards
Direct Dock
Direct dock style wafer probing allows for a higher bandwidth, increased pin density and testing more devices in parallel. Direct dock probe cards also support the growing movement of traditional final test to wafer probe which allows for known good die (KGD) and reduced cost of ownership.
-
product
Threaded Switch Probes
Product sensing - microswitch in a probe - plastic or metal cup - adjustable height.
-
product
Semiconductor Test & High-Speed Digital
Rosenberger Hochfrequenztechnik GmbH & Co. KG
The wide product range means that a variety of semiconductor test applications and high-speed digital applications are possible. To meet the ever-challenging technological requirements and increasing demands of the semiconductor test equipment industry, Rosenberger has developed and produces multiport mini-coax connectors and cable assemblies – for applications up to 40 GHz – , and spring-loaded coax products. Probes and customer-specific cable assemblies are also available.
-
product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Bias Ball Probe
POGO-1T30-10
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Adapter/Gold
WADP-SFSF
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
2-Channel Oscilloscope DIY Kit
WAVE2
WAVE2 is the latest 2-Channel Oscilloscope on the market, catered to hobbyists, educational institutions and professionals in the field of electronics and mechatronics. Featuring a bright and easy-to-use color touch screen display with access to many features only advance oscilloscopes offer such as built-in function generator and X-Y plotting. With an optional battery, it is portable enough to be taken wherever the jobs that need to be done is. Its an exciting project for any DIY-er, or can be purchased fully assembled for those who are looking to start using it right away. It comes with everything you need to start using it right away, with a micro-USB cable and two high-quality BNC probes. Enjoy and start creating!
-
product
Spring Contact Probes
We differentiated the spring contact probes by center and application, for the purpose of clarity. Please choose in the left navigation bar!
-
product
Temperature Calibrators
We offer temperature calibrators in different shapes. We offer temperature dry blocks that can generate an accurate temperature, for example for temperature sensor calibration. We also offer electrical temperature calibrators that can measure and simulate various temperature sensors (RTDs and thermocouples). We also offer high-accuracy reference temperature probes.
-
product
Probing & Analysis Adapters
No matter how well designed a circuit is, there is almost always a need to hook up test instruments to it to verify function, look for bugs, or baseline performance. As IC packages become smaller and pin counts grow this becomes harder and harder. probing adapters are required to alleviate this de-bug problem. Many different types of adapters fall into the test and debug category. The common feature is that they bring the signals of an IC out to a format that is easy to interface with test and analysis equipment.
-
product
AC/DC Current Probe (1-Channel), 3 MHz, 50 UA
N2821A
As modern battery-powered devices and integrated circuits become more green and energy efficient, there is a growing need to make high-sensitivity, low-level current measurements to ensure the current consumption of these devices is in acceptable limits. The N2821A high-sensitivity probe is engineered to make high-dynamic-range, high-sensitivity measurements to meet today’s challenging current measurement needs.
-
product
Irradiance Probe
LP471RAD
Radiometric probe for measuring the IRRADIANCE in the spectral range 400 nm…1050 nm, cosine correction diffuser.
-
product
Ultra High 1.77 (50.00) - 10.00 (183.00) Bead Probe
BTP-25HF-10
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Test Kit
Metriso B530
Wolfgang Warmbier GmbH & Co. KG
Test voltage / Test current: 1 mA < I < 1,3 mAHigh ohmic range: DC 10 volts,100 volts and 500 voltsTest range:low ohmic range: 1 to 10 kOhmhigh ohmic range: 1 kOhm to 199 GOhmOperation: Battery operatedProbes:2x Model 870 (weight: 2,27 kg / ø 63,5 mm) with conductive rubber (grey) and extension,1x hand-held probe Model 45
