1553 Interfaces
Mil-Std-1553 interfaces.
-
product
Quad Serial FPDP Interface with Virtex-6 FPGA - XMC
Model 71611
- Complete Serial FPDP solution- Fully compliant with VITA 17.1 specification- Up to 2 GB of DDR3 SDRAM- PCI Express interface up to x8- LVDS connections to the Virtex-6 FPGA for custom I/O
-
product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-94
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
DAS Trays/ Point-of-Interface (POI)
*CCI DAS Trays provide a common connection point to the DAS system for multiple BTS's*Modular design allows support for bands from 700MHz to 2700 MHz*Independent level control for each BTS for adjusting TX & RX power*Easy optimization features including separate Uplink and Downlink control*Can support both 0 dBm and +30 dBmDAS TX inputs (high and low power)*Supports NIMO and SIMO configurations
-
product
PCI 8 Form C Relay Output / 8 Isolated Input Digital Interface
8011
The 8011 digital I/O interface provides 8 optically isolated inputs and 8 Form C relay outputs. The inputs protect the PC and other sensitive equipment from spikes and ground loop current that can be generated in industrial environments, while the outputs provide higher current capabilities (up to 2A) and are optimized for 24V operation.
-
product
Ethernet Digital Interface OEM Board
8063
* Same Digital IO lines as standard 8063. * Same data transfer capabilities as standard 8063 * Digital I/O uses high-density DC-62 connector.* Power connections via 2 screw terminal strip or solder pads.* User configured IDN message and webserver pages makes board respond as part of your system.* Use an ICS Wiring Kit to extend the Ethernet signal to a rear panel RJ45 jack.* Runs on 9 to 32 Vdc power.
-
product
Hall Sensor Board with I2C Interface
050-279
Version: +5V/90A +3,3V/25A +12V/60A +12V/60A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
PXI Remote Control Interface Cable, 3m
41-924-300
The 41-924-300 is a 3m cable accessory for the PCIe to PXI Remote Control Interface Kit. The kit provides a seamless connection between a PC’s PCIe slot and a PXI chassis and is suitable for providing an interface to any PXI chassis.
-
product
PMC Compatible Bi-Directional Serial Data Interface
PMC-BiSerial II
The PMC BiSerial has been updated to be even better. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-II. The BiSerial II features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
product
PCI Express to VME Interface
SIS1100-E2/3104-2
The SIS1100-e2/SIS3104-2 interface/bus coupler is the choice for demanding VME readout applications. VME block tranfser speeds up to 160 MByte/s are readily accomplished in conjunction with state of the art VME slave hardware.
-
product
HMI Operator Interface Panels
- Robust and powerful HMI for operation and monitoring- Programmable and parameterizable to IEC 61131-3 with CODESYS- Vibration and shock resistant housings with high protection rating- Units for surface or panel mounting- Powerful interfaces for various communication tasks
-
product
USB Controlled High Precision Audio Test Interface
AudioConnect 4×4
AudioConnect 4×4 is a high accuracy 4-in, 4-out audio interface specifically audio test and measurement. It offers digital and analog audio in and out at any user-specified sampling rate up to 200kHz, and a high signal to noise ratio and wide frequency response, making it suitable for the most demanding measurement applications. Controls are simple – a single USB connection and a power indicator – all other typical soundcard controls that are not used for audio test applications have been eliminated to make operation and calibration simple with no room for error. AudioConnect 4×4 is supplied fully calibrated.
-
product
3U OpenVPX Sensor Interface Unit
SIU32S
The SIU32S is a highly configurable Modular Open Systems Approach (MOSA) rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, processing, communications and Ethernet switching. The SIU32S leverages NAI’s Configurable Open Systems Architecture™ (COSA®) 3U boards and smart function modules to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
Hall Sensor Board with I2C Interface
050-280
Version: +24V/60A -24V/60A -5,2V/90A -2V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
GPIB Analog Interfaces
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
product
Power Interface Board 3U, 1PSU connector
106PIBM301-0000R
The PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
product
Isolated Four-Port Serial Interface Cards
PCI-ICM422-4 and PCI-ICM485-4
These cards can be installed in any 5-volt PCI-bus computer that can accommodate "long" cards and are designed to provide effective communication on long communication lines in noisy environments. The data lines are opto-isolated from the computer and from each other to assure communication even when large common mode noise and voltages are superimposed. Type 16550 UARTs are used. These include a 16-byte transmit/receive FIFO buffer to insure against lost data in multitasking operating systems. All ports are independently addressable and an on-board crystal-controlled oscillator permits precise selection of baud rates up to 115,200 baud or, by changing a jumper, up to 460,800 baud.
-
product
CPRI Interface Panel Kits for Connectivity Testing
RFS’ CPRI Interface Panels are used to test fiber connectivity between Optical Base Band Units (BBU) and Remote Radio Heads (RRH), allowing cell operations and system performance engineers to ensure the best performance without having to disconnect the fiber optical system or disrupt service. In addition, the CPRI panel enables easy RF over CPRI testing at the bottom of the tower, reducing the need for unnecessary tower climbs, thus minimizing maintenance cost and overall OPEX for customers. The RFS CPRI panel is bundled with RFS’ high-quality fiber optic jumpers, providing an end-to-end solution that includes HYBRIFLEX® fiber-to-the-antenna DC and F/O solutions.
-
product
PXI/PXIe Remote Control Interface Modules And Kits
Take advantage of the latest high-performance, low-cost desktop PCs for control of your PXI system.
-
product
4 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTC
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Serial Digital Interface
Model 2363
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* RS-232 and RS-485 Serial IO.* 1 U high rack mount kit mounts one or two 2363s* Includes US 115 VAC Power Adapter
-
product
Audio Interfaces
Lynx
Lynx offers a range of audio interfaces that work well with SoundCheck. Listen supplies Lynx interfaces fully tested and pre-calibrated for use with SoundCheck.
-
product
IEEE 488 PXI GPIB Instrument Control Module
778039-01
The PXI‑GPIB is an IEEE 488 controller module for PXI systems. You can use this module to integrate non-PXI instruments into your PXI system using GPIB. The PXI‑GPIB achieves maximum IEEE 488.2 transfer rates. This module … includes a license for the NI‑488.2 driver software, which provides maximum reliability for connecting to third-party instruments with GPIB.
-
product
Test Interface Solutions
As the leading independent provider of pick-and-place handler change kits, we provide the best quality and affordable kit using only the most robust materials.
-
product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UTT 306 x 248 mm
MG-02-01
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 4 interface blocks of 160 signals• All interface blocks can be customized
-
product
Sample Conditioning Communications Interface
Pilot Pro Series
Parker's Pilot Pro™ package has been designed with a high level of flexibility to accommodate multiple configurations of local area communications networks.
-
product
Upgrade User-Installable GPIB Interface Board For AC6900B Series AC Sources
AC69GPBU
The AC69GPBU is a user-installable GPIB interface module upgrade for Keysight AC6900 Series basic AC power sources.
-
product
Reference Grade Expandable Production Interface
Atlas
Atlas and Titan are world class multi-track interfaces offering flexible expansion and unsurpassable sonic clarity. Using the latest generation of Prism Sounds trusted conversion, Atlas provides more preamps than Titan making it suitable for a wider range of recording scenarios.
-
product
Peripherals & Interface Cards
Interface cards are plug-in modules that provide interfaces for control/communication of/with external components or test items.The modules themselves are controlled via standard interfaces such as USB 2.0/3.0, PCI, PCIe, PXI, PXIe or LAN.
