1553 Interfaces
Mil-Std-1553 interfaces.
-
Product
Avionics Interfaces & Test Instruments
ARINC 664
-
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
Product
Interface Converter
ZET 7176
-
Interface converter Ethernet/Wi-Fi↔CAN ZET 7176 is used for connection of CAN interface instrument communications nets based on digital transducers to PC over Wi-Fi or Ethernet. Wi-Fi or Ethernet network throughput rate allows to immediately fulfill commands and transmit great scope of data. Shared use of ZET7176 and ZET 7172 interface converters allows arranging instrument communications nets with radio linked transmission interface.
-
Product
Modbus Register Converter - Serial To Modbus RTU Interface
-
Translates Modbus registers and variable types from an older Modbus devices to a new Modbus device. The Model 2390 allows upgrading Modbus RTU devices without changing the system software. The 2390 also provides serial control of Modbus RTU devices for new applications that want the ease of using simple ASCII commands strings when controlling Modbus RTU devices.
-
Product
CANBus & Interface Card
Interface Card
Advantech has developed a series of APIs for customers to access Controller Area Network (CANBus) Protocols which are Compliant with CAN 2.0A and CAN 2.0B identifiers according to ISO 11898-1 and ISO 11898-2. The form factors of most modules are combination of full-size Mini PCIe & module types, easy to fit different applications.
-
Product
Interface Cards / PoE Injector
-
Gigabit Ethernet with PoE allows for single cable camera solutions, simplifying installation and maintenance. For those who will be externally powering the camera we offer a single port Gigabit Ethernet card and a PoE injector unit.
-
Product
Interface And Load Box
MS 3646I
-
Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.
-
Product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Advanced MIL-STD-1553 & ARINC LabVIEW Software
AltaAPI-LV
-
Most of Alta’s MIL-STD-1553 & ARINC products include the industry’s most advanced National Instruments’ LabVIEW™ & RT Support Tools, AltaAPI-LV. Built-in native NI LabWindows™ environment and PCI VISA drivers, Alta’s AltaAPI-LV provides a unified NI tool for easy integration to LabVIEW, RT, and LabWindows™ applications. Easily port native DLLs for Testbench or VIs for Veristand.
-
Product
Hall Sensor Board with I2C Interface
048-368
-
Version: +5V/60A +5V/60A +3,3V/25A +12V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Handler/Prober Interfaces
IFXX
-
FETtest offers a variety of Interface options, which expand test capability and provide connection to other production line resources. These interfaces range in complexity from simple handler/prober interfaces to interfaces with user programmable external component connections, to capacitance measurement systems. Models are available to work with the full range of FETtest systems and Remote Stations.
-
Product
Power Amplifer AURORA Digital Interface For Simulator Application
PAV DIA01
-
PAV DIA01 is the optional accessory unit and Aurora digital interface for PONOVO’s power amplifiers which could convert the analog input signal into digital signal, supporting communication between power amplifier and simulators via AURORA protocol.
-
Product
Interface Between the Operator and the Sensor
Controller
-
The high-resolution touch screen provides best technical comfort and a virtual keyboard, including Latin, Asian and Cyrillic characters. A real time chart shows the trends and provides quick and clear information about the current process cycle, while the menu and display functions are clearly laid out. The user interface is intuitive and simple to use. Password-protected user administration and a stable, comprehensive data memory for all process values and events ensure the traceability, reliability and safety of the system.
-
Product
Interface Adapter
DMX-10
-
DMX-10 is, all-in-one ready to use PCIEx to I2C/SPI/GPIO Interface adapter based on system with FPGA and 1x PCIEx PHY. DMX-10 converts PCIEx transactions into the I2C, SPI master or slave transactions and GPIO control functions. DMX-10 turns your PC running Windows, DOS, Linux, MacOS or any embedded OS with PCI support into comprehensive general purpose bus master or slave adapter.
-
Product
Multi Interface USB Adapter
SUB-20
-
SUB-20 is a versatile and efficient bridge device providing simple interconnect between PC (USB host) and different HW devices and systems via popular interfaces such as I2C, SPI, MDIO, RS232, RS485, SMBus, ModBus, IR and others. It is also a full "any to any" converter between all supported interfaces and I/O features. SUB-20 is a powerful I/O controller with 32 GPIO, 8 Analog Inputs, PWM Outputs, Edge DEtectors, LCD, Leds and push buttons.SUB-20 system includes SW package containing driver, API Library, GUI and Command Line based applications, C,C++,C#,VB.net, MATLAB, LabView sample code and documentation. SUB-20 can be used with PC 64/32 bit running Windows 2000/XP/Vista/Win7/Win8, MacOS, Unix/Linux and DOS.Working with SUB-20 does not require deep knowledge of low layers of the specific interface. All you need to do is to call right API function at the right place. And this is really very easy as API functions are well documented and "exampled". API set is relatively small but comprehensive.SUB-20 is equipped with status Leds, optional LCD and buttons. All this guarantee fast and comfortable development, field debugging and maintenance of applications including option of standalone operation.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Serial Parallel Interface
Model 2313
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
Product
CAN Sensor/ Interface
Current
-
Reach Technologies’ CAN Current Sensors sense and digitize conductor current for collection via CAN. The module is ideal for conveniently adding current data to a distributed CAN network. The CAN Current Sensor is configurable via J1939 or CANopen stacks, and are available in Hall Effect and shunt variants.
-
Product
PCI Express to VME interface
SIS1100e/3104
-
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
-
-
Product
Ethernet-GPIB-USB to Serial Interface
Model 9006
-
* All interfaces provide full communication with the serial device.* Ethernet port supports VXI-11 and raw socket protocols.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* GPIB port is IEEE-488.2 compatible.* USB port uses Microsoft supplied driver to prevent driver problems with operating system change problems.* Serial port provides RS-232 and 2 or 4-wire RS-485 signals.* Supports devices that generate asynchronous messages, devices that respond when queried and smart devices.* Internal webserver for easy configuration from any browser.* Board runs on 5 to 15 Vdc power.* Includes ICS's VXI-11 and VISA keyboard control programs.* Works with Agilent, NI and Kikisui VISA libraries.
-
Product
Ethernet 48-Channel Digital I/O Interface
2410
-
Controls/monitors 48 digital signals over Ethernet PWM output mode Programmable input debounce Input edge detection with asynchronous host notification Compatible with standard solid state relay racks Embedded HTTP and Telnet servers Open source API
-
Product
Message Based Intelligent Interface Card
IIB-3910-VXI
-
The IIB-3910-VXI is message based intelligent interface card for dual redundant 3910 and 3838 applications. It gives full 3910 and 3838 test, simulation and bus analysis capability on the VXI bus, providing 3910, 3838 1553A, and 1553B variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with passive Bus Monitor, and an independent Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides dual redundant prEN3715 compatible 3910 interface, with variable amplitude dual redundant 3838 interfaces. External trigger-in and trigger-out are provided, with both Primary and secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel.
-
Product
TTENetwork Interface Cards
-
The TTENetwork Interface Cards are pluggable mezzanine cards for network communication combining regular Ethernet with the safety-critical time-triggered technology from TTTech. They enable real-time Gbit/s Ethernet communication between a computer and TTESwitches for redundant channels in a safety-critical way.
-
Product
Primus Epic Interface Kit
LANTAP-10
-
Innovative Control Systems, Inc.
*LANTAP-10 kit comes with 10’ Coaxial cable, 6’ USB cable, 6’ CAT5 cable, BNC Connector and Terminator.*Allows connection of any 10/100/1000 Ethernet equipped system to EPIC equipped *Aircraft LAN or ANY 10base2 need.*No drivers to install. The LANTAP is NOT a USB device. It is only powered by USB.*Complies to IEEE 802.3 10Base-T and 10Base2*LED diagnostics and monitoring indicators
-
Product
9 Pin Breakout Interface
VSI-Breakout-9
-
The VSI-Breakout-9 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Human Machine Interface
-
Panasonic Automotive & Industrial Systems Europe GmbH
combines state-of-the-art features and top performance with an outstanding design in an all-metal housing. The range consists of four models in sizes from 4.3", 7", 10.4" and 13.4" TFT color display with LED backlight. All models can be installed in a horizontal or vertical position. The touch terminals are equipped with an Ethernet port and support VNC technology, allowing both remote VNC applications and remote assistance. The HM500 series is programmed with the HMWin software, a simple and intuitive program, yet equipped with advanced features. It is possible to import variables from Control FPWIN Pro, the programming software for Panasonic PLCs, thereby facilitating the synergy between PLCs and HMIs. The products have a 5 year warranty.
-
Product
SIP-90-2 Test System Interface Probe
SIP-90-2
ICT/FCT Probe
Overall Length (mil): 700Overall Length (mm): 17.78Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
Hall Sensor Board with I2C Interface
055-013
-
Version: +5V/5A +3,3V/5A +12V/5A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Shuttle Bus PMC Intelligent Interface Card
IIB-SB-PMC
-
The Shuttle Bus PMC is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, Multiplex De-Multiplex Multiple Remote Terminal, and Ground Data Bus (GDB)capability to the Shuttle Bus, together with a Pulse Code Modulation Mode. This card provides all features and functions required in a PMC platform, withSimplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
Product
Isolated Four-Port Serial Interface Cards
PCI-ICM422-4 and PCI-ICM485-4
-
These cards can be installed in any 5-volt PCI-bus computer that can accommodate "long" cards and are designed to provide effective communication on long communication lines in noisy environments. The data lines are opto-isolated from the computer and from each other to assure communication even when large common mode noise and voltages are superimposed. Type 16550 UARTs are used. These include a 16-byte transmit/receive FIFO buffer to insure against lost data in multitasking operating systems. All ports are independently addressable and an on-board crystal-controlled oscillator permits precise selection of baud rates up to 115,200 baud or, by changing a jumper, up to 460,800 baud.
