-
product
PXI Fault Insertion (Fault Injection) Modules
PXI Fault Insertion Units (FIU), also known as Fault Injection switch products, are designed specifically for safety-critical applications where the response of a control system is required to be evaluated when sensor connections behave in unexpected ways. These modules are scalable solutions that can be used to switch signals between simulations and real-life devices in a multitude of hardware-in-the-loop (HIL) simulation and test systems. The fault insertion unit can significantly simplify and accelerate the testing, diagnosis and integration work in HIL applications.
-
product
PXI-4110, 3-Channel, 20 V, 1 A, 46 W, PXI Programmable Power Supply
779647-11
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
product
Regenerative AC Emulator, 600 VAC, 63 A, 30 KVA, 3‑Phase
SL1201A
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2.5Ω to 773kΩ
40-251-043
The 40-251-043 is a programmable resistor module with 2 channesl which can be set between 2.5Ω and 773kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Regenerative Grid Simulators 9kVA-15kVA
Chroma Systems Solutions, Inc.
Four quadrant, single- or three-phase AC power sources designed to simulate real-world grid characteristics for EV, PV inverter, and smart-grid test applications.
-
product
Environmental Chambers
Whatever your application, from an environmental chamber for small components to an extensive array for a complete automobile or aircraft test, EYE / Iwasaki has the experience to provide a solar lighting system customized for your requirements. Our systems are designed to be flexible and deliver the optimum solar simulation solution. We do not force-fit a "standard" system to attempt to meet your needs.
-
product
PXI RF Multiplexer Switch Module
PXI RF Multiplexer Switch Modules are ideal for high-channel-count applications that need to connect measurement or signal generation instruments to various test points on devices or units under test(DUTs or UUTs). PXI RF Multiplexer Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor(FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a multiplexer that fits your requirements. To pro...show more -
product
True RMS Power Sensors
LadyBug True RMS Average Power Sensors deliver reliable, accurate power measurements for CW, Pulse, and modulated signals. These diode based sensors feature a wide dynamic range and a great VSWR. The optional external triggering input feature can be used without any external components. Recorder and Trigger outputs are also available. Our patented NoZero NoCal technology make these sensors ideal for calibration systems, automated test stations and other embedded applications.
-
product
User Defined Application Software
D9010UDAA
User defined application (UDA) is a fully customizable automated test application for your DCA, Infiniium or InfiniiVision oscilloscope. It provides full automation, including the ability to control other test and measurement devices. The development environment is free to download today, so you can begin to create your own UDAs. Simply download the software, install it on your desktop or scope, and begin developing the automated test packages you need.
-
product
Handheld Digital Video Generator and Analyzer
780C
The Teledyne LeCroy quantumdata 780C is a handheld digital video generator and analyzer that enables you to run tests on various digital video devices and network distribution devices on site or in the R&D lab. The 780C instrument provides a 7 inch color touch screen for operation and for viewing status of outgoing and incoming video and audio. The 780C is equipped with multiple interface types including HDMI, HDBaseT, 3G-SDI and component analog. Testing digital interfaces is supported by b...show more -
product
Multiport Electronic Calibration Module (ECal), DC To 9 GHz, 6-ports
N7562A
A series of multiport ECal that cascade-able up to 36-ports which makes it possible to calibrate a wide frequency range from DC up to 9 GHz without making numerous connections during calibration process. Ideal for multiport measurement application with VNA in such as high-volume PA/FEM, massive MIMO antenna or high-speed digital interconnect test applications
-
product
PCI High Density Potentiometer Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-296A-121-3/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 31.5Ω
50-298-010
The 50-298-010 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
LCA TAP Plug-In
N4370P01A
Keysight Test Automation on PathWave (TAP) is a modern Microsoft .NET-based application for standalone use or in combination with higher level test executive software environments. Instrument plug-ins provide test steps that can be added to work-flow sequences without instrument level programming commands. The LCA plug-in steps further simplify automation by handling the interface to both the PNA instrument and the LCA optical hardware and software and providing the test steps for easy configuration.
-
product
LED Light Tester
The T100L Automatic LED Light Test Equipment is designed to identify the presence of any defects of electronic components for LED light applications, addressing any high-volume production testing challenges without needing expensive test fixtures with fiber optics
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm - SPST
50-294-124
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Keysight 70-Channel Reed Multiplexer for 34980A
34924A
The Keysight 34924A module for the 34980A Multifunction Switch/Measure Unit is a high-density, high-speed multiplexer for general purpose scanning. It uses reed relays to achieve scan rates up to 500 channels-per-second. Use this module for high-throughput automated test applications as well as high-speed data logging and monitoring tasks.
-
product
Bias Network, 45 MHz to 26.5 GHz
11612A
The Keysight 11612A broadband high power bias network can be used in a wide variety of biasing applications for test and measurement requirements in laboratory and production environments. Bias networks provide the means of supplying DC bias to the center conductor of the coax connector for your device while blocking the DC to the RF port.
-
product
KWH Meter Test Bench
This test bench is widely used in electrical and engineering sector for varied testing applications.
-
product
Controller
ServoEDGE
ServoEDGE is an integrated, multi-loop control and data acquisition system designed specifically for hydraulic and servo-hydraulic applications, including system modernizations, new installations, turnkey systems and complete test cell control and data acquisition systems. The system is designed and pre-configured using both NI PXI hardware and Genuen's integrated connector blocks and power module, which minimize cost and simplify connectivity and integration. The configured system provides a wide range of I/O capabilities for typical hydraulic applications; and since the system is based on off-the-shelf hardware, it can be easily modified to cover a wide range of I/O requirements.
-
product
Entry Level Loss Tester
Model：OLT-20
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
product
Exhaust Gas Thermocouples
HYBRID Series
The AMETEK Hybrid Series Exhaust Gas Thermocouples for Frame 7 and 9 applications have been designed, fully tested and qualified to meet OEM specifications. AMETEK has worked closely with the OEM turbine manufacturer to qualify and engine test this thermocouple as a direct replacement, or for upgrading an older style Exhaust Gas Thermocouple.
-
product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
product
Phase Locked Loop with Integrated VCO
PLL with integrated VCOs provide local oscillator sources and clock sources for communications (COMMS) , test and measurement (ETM) and aerospace/defense (ADEF) applications. ADI's PLLs with integrated VCO portfolio includes both narrowband and wideband parts, supporting frequencies up to 13.6GHz. Our PLLs with integrated VCO, as well as our full PLL portfolio including integer-N and fractional-N PLLs, feature best-in-class performance for phase noise, jitter, and spurious, and also feature high levels of integration in small form factor packages.
-
product
Clamp Meter
ST-3347W
Standard Instruments Co., LTD.
This clamp meter provides accurate AC, AC/DC current and voltage readings regardless of the waveforms. This meter can use in most industrial and commercial applications where non-linear loads distort the current or voltage waveform. Reliable operation. Features accessories such as test leads, carrying case and temperature probe.
-
product
MIMIC® IPMI Simulator
The MIMIC IPMI Simulator, the industry’s first integrated simulation tool supporting IPMI, allows developers to perform real world, integrated device simulations. MIMIC simulates IPMI-capable high-end server systems. MIMIC allows suppliers of IPMI devices and applications to design, develop and test their products in a virtual and scalable network environment, assuring customers that their applications will work properly when deployed across heterogeneous environments.
-
product
LED Test Production System
Lumere-LC
Evolusys Technologies Sdn. Bhd.
Lumere LC is a LED test and measurement system for various parameters of LED light. It is economical, its geometry conforms with CIE-Publication 127, and the test program is easy to configure and adjust. Main application is in the production of LEDs.
-
product
Squeak And Rattle Test Solutions
Annoying noises like squeaks and rattles have become a significant quality issue for customers of passenger vehicles, light & heavy commercial vehicles, increasingly off-road vehicles, and even airplane applications. These unwanted sounds are a problem for numerous reasons including customer dissatisfaction, sizeable warranty expense, and the overlying difficulty to diagnose and fix. MB Dynamics offers an innovative line of Buzz, Squeak & Rattle (BSR) or Squeak and Rattle (S&R) Test Solutions, focused on helping to eliminate annoying noises through prevention, design verification testing, and production verification testing, before the product reaches the customer. -
product
Modular DC Electronic Load LED Simulator
6310/A
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
-
product
PXI-2599, 26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module
778572-99
26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module - The PXI‑2599 is a general-purpose single‑pole double‑throw (SPDT) switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2599 is also well-suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
