Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
C Series Counter Input Module
Input/Output Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, and counter measurements in your chassis.The C Series Counter Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Multifunction Counter (Pulse Input)
CM1-CT
-
CM1-CT multifunction counter(position) display controller, is design to have 2 pulse input, for proximity switch, photoelectric sensor, encoder etc.. Counting increase or decrease, positioning batch count etc.. display, with External input and Modbus communication port.Multiple types of input mode, trip mode setting to fulfil easy usage and requirement for counter controller. For different requirement, the meter can be with 2 relay or 1 Analogue output or 1 RS485(Modbus RTD mode) communication. (Choose 1 kind of output from the 3 options)
-
Product
mAEStro Audio Digital to Analog Converter
-
The mAEStro ADAC-100 receives AES/EBU (AES3) or S/PDIF digital audio and converts it to two channels of analog audio. It automatically detects sample rates up to 96kHz with low-jitter clock recovery. Two balanced line-level audio outputs are provided on XLR connectors on the rear panel. For convenient monitoring, a stereo headphone mini-jack and volume control are provided on the front panel.
-
Product
Batch Controller (pulse input)
-
A low-cost controller for repetitive fill operations. The typical application utilizes a flow meter input and two built-in relays: a Prewarn relay slows down the pump near a preset to avoid overshoot and a Batch relay stops the pump at the preset.
-
Product
Isolation Amplifier Digital Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
Oscilloscope 200 MHz, 2 Analog Channels
DSOX3022G
Oscilloscope
The DSOX3022G 200 MHz oscilloscope provides 2 analog channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
16-Ch SSR Output IDAQ Module
iDAQ-763D
-
Hot-swappable in iDAQ systemDetachable Euro-type spring terminal connectors8-ch Form A solid-state relay (SSR) output600VRMS isolation for relay outputsSupports buffered update rates up to 500Hz
-
Product
Oscilloscope - 500 MHz, 2 Analog Channels
DSOX4052A
Oscilloscope
500 MHz2 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
External Sensor Input Type Handheld Digital Tachometer
HT-6200
-
HT-6200 is a handheld tachometer with a built-in batteries designed for measurement of gasoline/diesel engines, EV/HEV motors, and general rotating objects. Combined with optional detectors (VP-202/1220, IP-292/296, IP-3000A, IP-3100, OM-1200/1500, MP series and TTL signal output detector etc.), various rotation measurement are possible depending on the measurement objects or purpose.
-
Product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
Digital I/O
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Oscilloscope 40 GHz, 4 Channels, 1 mm Inputs
UXR0404BP
Oscilloscope
UXR0404BP Infiniium UXR-Series is the 40 GHz, 4 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
Product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
Digital I/O
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Provides 3 Wire Voltage Output
SEM1620
-
The SEM1620 signal conditioner provides a 3 wire isolated voltage output signal and accepts RTD, Thermocouple, mV and passive current sensor inputs
-
Product
Digital Output Board, 32 Isolated Channels, 24V
APCIE-2032
-
32 digital outputs, 24 V or 5 V, 500 mA/channel Optical isolation 1000 V Overvoltage protection Short-circuit protection WatchdogAt power-on the outputs are reset to ì0î
-
Product
Digital output version optical fast DO sensor
RINKO II / II D
-
Rinko II is a digital output version with a fast-response optical DO sensor. The instrument can be easily integrated on platforms, because it works with communications by RS-232C or RS-485 and an external power (12 to 24V DC).Rinko IID has not only a temperature sensor but also a depth sensor. Their models can monitor DO in real time, if you have a personal computer and an external power.
-
Product
6GHz RF Analog Signal Generator Module
LS6081D
Signal Generator
The LS6081D, 6GHz Single Channel RF Analog Signal Generator, offers industry leading performance, combined with a compact small footprint form factor. The LS6081D features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6081D was designed to offer industry leading price to performance ratio, needed from the R&D benches to the production lines.
-
Product
Analog I/O Modules
-
iDAQ-800 Series delivers up to 24-bit, 1 MS/s acquisition with 600 VRMS isolation and sync, ideal for accurate, high-speed industrial measurements.
-
Product
Conventional Power Supply Design with Simple Analog Controls
VLF Series
-
VLF hipots perform voltage withstand tests and provide the voltage source for diagnostic cable testing. There is no better method for verifying the AC integrity of a cable than applying VLF AC voltage. Tan delta and partial discharge measurement accessories are frequently purchased along with VLF equipment to extend their capabilities.
-
Product
USB-TC01, 1-Channel Temperature Input Device
781314-02
Temperature Input Module
The USB‑TC01 is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take … temperature measurements with your PC. You can connect the USB‑TC01 to any USB port to use your PC as a display and monitor data in real time. The USB‑TC01 is compatible with J, K, R, S, T, N, E, and B thermocouples.
-
Product
20mhz 2 Channel Analog Oscilloscope
MOS-620CH
-
Shenzhen Chuangxin Instruments Co., Ltd.
20mhz 2 channel analog oscilloscope
-
Product
50W to 1500W - Single Output
RWS-B Series
-
*10 Year e-cap Lifetime*85 - 265VAC Input (300VAC for 5s)*UL 508 Certification on Select Models*Compact Size*7 year warranty
-
Product
PXI RF Analog Signal Generator
Signal Generator
PXI RF Analog Signal Generators deliver the functionality of RF signal generators to the modular, compact PXI form factor. These modules support frequency ranges from 250 kHz to 20 GHz. You can combine PXI RF Analog Signal Generators with other PXI modular instrumentation to design automated test systems for radar, RF integrated circuits (RFICs), and automotive test applications.
-
Product
47~862MHz Four outputs FTTP CATV optical receiver
P9428
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai P9428, the operating bandwidth of 47 ~ 862MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver. Products with high sensitivity optical receiver tube and Huatai special low noise matching circuit..
-
Product
Infiniium S-Series High-Definition Oscilloscope: 4 GHz, 4 Analog Channels
DSOS404A
Oscilloscope
4 GHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.2 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
HPx-200 PCI Radar Input Card
-
The HPx-200 is a flexible, cost-effective PCI primary radar acquisition card that captures and processes one or two analogue or digital radar video signals from a single radar. The card is fully supported by SPx software, allowing modern radar processing to be added into legacy systems.
-
Product
PCI Express 16 Reed Relay Output Digital Interface
8003e
-
The 8003e PCI Express digital I/O interface provides 16 Reed relay outputs. The outputs provide high quality, long-life, dry contact switch closures suitable for low-current applications up to 10VA. Reed relays are normally open and close when energized. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
Oscilloscope - 500 MHz, 4 Analog Channels
DSOX3054T
Oscilloscope
500 MHz4 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
32-CH Discrete Input Daughter Board Module
HSL-DI32-DB-N
Digital Input Module
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type sensor inputs or dry contact*Photo couple isolation voltage: 2500Vrms*Input impedance: 4.7KΩ*Input current: ??10mA (Max), ??12.5mA (Peak)*Input voltage: ??40V (Max)
-
Product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 8 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
APCI-3120-16-8
-
*Optical isolation 500 V*16 SE or 8 diff. inputs*Data transfer rate: 100 kHz*16-bit resolution*8 analog output channels*Data transfer rate:30 kHz*14-bit resolution
