Solder Paste Inspection
assures volume and area of paste application.
See Also: Solder Paste, Solder Paste Measurement, 3D Solder Paste Inspection
-
Product
Inspection System for high-power precise 3D X-ray CT
X-eye PCT225
-
Inspection System for 3D X-ray CT able to analyze defected area precisely by precise movement of axis with high polished Anti-vibration table. High-power X-ray Tube of max. 450kV and large area Flat Panel Detector of max.16 inches can be installed depending on the sample. Customized 3D CT equipment is available with selecting main parts by customers depends on their needs for size and material.
-
Product
25-Pin D-Type Female Solder Bucket
92-960-025-F
D-Sub Female Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
X5 Pack X-Ray Inspection
-
Designed to be integrated into line with built-in automatic reject and available in 300, 500 and 600 mm belt width models, the X5 Pack is perfect for a variety of unpackaged and packaged products.
-
Product
Non-Destructive Resonant Inspection Drop Test Fixture
RAM-DROP
-
The Drop Test Fixture, Model RAM-DROP, Resonant Inspection System, allows automated sorting and quality testing of small metal injection molded (MIM), powder injection molded (PIM), additively manufactured, and other small parts by using the Resonant Acoustic Method (NDT-RAM).
-
Product
Building Inspection System with Moisture Hygrometer & MSX® IR Camera
FLIR MR277
-
The MR277 is the first FLIR building inspection system to combine the advantages of Infrared Guided Measurement (IGM) and our patented Multi-Spectral Dynamic Imaging (MSX) with advanced environmental sensors to help you quickly locate, clearly identify, and easily document problems. IGM technology and a laser pointer isolate the area where you can use the integrated pinless moisture sensor for non-invasive readings or external pin probe for invasive measurements. With automatically calculated environmental readings and a field-replaceable humidity/temperature sensor, the MR277 lets you finish the job and minimize downtime. Connect to external devices with METERLiNK® and use FLIR Tools® to enhance troubleshooting and reports.
-
Product
Automatic Double-Sided Bare PCB Final Inspection AVI System
FI-18 Series
-
InScan Limited (SIP) Co., Ltd.
InScan FI-18 is a compact and high performance fully automatic double sided AVI system for Final Inspection of PCB boards.The setup is based on golden board and CAD data which greatly simplifies the setup process. The FI-18 series inspects and processes a double sided board sized 210X300 mm 5.5 sec. Superior interline high resolution CCD sensor.
-
Product
High-speed In-Line 3D CT Inspection System
X-eye 6300
-
Automatically inspects the defects of products in customer's line with high-speed 3D CT tomography.Able to inspect every defects of Double-sided PCBA & BGA mounted components precisely by solving overlapped X-ray image issue.Inspection speed of 3 sec/1FOV from loading to automatic Good/NG judgement.
-
Product
First Article Inspection Machine
Optima III FAI
-
Landrex Technologies Co., Ltd.
First Article Inspection Machine
-
Product
Chip Inspection System
GEN3000T
-
GEN3000T is an inspection system that performs automatic inspection of individual semiconductor chips.This revolutionary chip surface inspection system was achieved by combining the chip handling technology cultivated by Toray with the inspection algorithm used in the "INSPECTRA®" wafer defect inspection system.
-
Product
Digital Automated Interferometer for Surface Inspection
DAISI
-
DAISI (Digital Automated Interferometer for Surface Inspection) achieves the high workability and repeatability with the features such as auto-focus function, auto-calibration function and auto connector fixing system.
-
Product
3D Digital Inspection
-
Digital stereo 3D imaging is a unique, advanced, stereo image presentation system designed to provide fully interactive real time natural 3D viewing and visualisation with outstanding depth perception.
-
Product
Industrial CT X-Ray Inspection System
X3000
-
The X3000 is North Star Imaging’s newest standard system. Whether you are inspecting small or large components, the X3000 is the best option for customers needing a compact system with unique capabilities generally available on a larger X-ray or CT system.
-
Product
Pinhole Detection Inspection Kit
Elcometer 270
-
The Elcometer 270 Pinhole Detectors Inspection Kit utilises the wet sponge technique and has been designed to set a new standard for wet sponge detectors - a high quality, low voltage detector with similar accessories to a high voltage spark tester.
-
Product
Packaged Food X-ray Inspection System
EPX100
-
Our revolutionary new x-ray system is so advanced it will not only improve your product safety and meet regulatory compliance but also will optimize and streamline your product inspection.
-
Product
A Compact X-ray Inspection System, The MedaScope™ Desktop
-
A compact X-ray machine weighing only 55 pounds, the MedaScope Desktop is easy to carry and can be set up rapidly. Glenbrook’s MedaScope Desktop is a portable, compact manual system for real-time, magnified x-ray screening of packaged devices including medical devices, electronics, and cables.
-
Product
Replacement Solder Tip Leadset for Use with D410/D610
Dx10-SI-HiTEMP
-
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
Product
37-Pin D-Type Female Solder Pin HV
92-960-037-F-HV
D-Sub Female Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Video Inspection Scope
BK3000
-
• Integrated 8.5 mm high-res imager allows for ease of use and ensures the product is always ready to go. Imager is resistant to dust, dirt, and water ingress for 30 minutes at depths of up to 3 meters.
-
Product
68-Pin Micro-D Male Solder Bucket With Backshell
40-962B-068-SB-M
SCSI Male Connector
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Wafer Inspection Machine
IV-W2000
-
The IV-W2000 is a wafer inspection machine that features on-the-fly scanning and inspection as well as automatic handling of 6/8/12-inch wafers. With the option to have a Chinese language UI, this machine is also known for being intuitive and user-friendly.
-
Product
Replacement Solder Tip Lead Set for D410/D610
Dx10-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Highly Integrated Optical Inspection
BOA
-
BOA is a highly integrated optical inspection tool for controlling quality and increasing productivity. It comprises all the elements of an industrial machine vision system in a tiny smart camera style package.
-
Product
Visual Counting & Inspection Systems
-
Sciotex has created a comprehensive line of visual counting and inspection systems. These systems can be custom configured for a wide range of applications and are often delivered, ready-for-installation in your environment.Our Products:PerfectCount, Ball Coleman SeedView, ConveyorView Inspection Systems, Sciotex ImageView, MultiView Inspection Systems
-
Product
TO-CAN Package Inspection System
7925
System
Chroma 7925 is an automatic inspection system for TO-CAN package. The appearance defects over 30 um like lens scratch, partial are clearly conspicuous by using advanced illumination technology. Because the height variation of tray and package exists, Chroma 7925 can calculate the focus distance and compensate to overcome the variation with auto focus function.
-
Product
Inspection System
X-eye 7000B
-
Appropriate for the inspection of medium•large size components and detection of surface structure and defects (inside voids and cracks etc).Due to high-energy, high-power Micro-focus X-ray Open Tube, maintenance cost's significantly reduced and long-term use possible with only replacing consumables.Customization is available with selecting main parts by customers depends on their needs for size and material.
-
Product
3D Automated Optical Inspection Systems
New 3Di Series
-
To handle today’s rapidly changing market trends, the system can handle complex inspection challenges such as high component mounting density areas containing highly miniaturized parts placed near much larger and taller component. With our new 3D AOI system, you can strengthen quality assurance and increase production efficiency.
-
Product
Thickness and Flaw Inspection
OmniScan MX2
-
The result of over 10 years of proven leadership in modular NDT test platforms, the OmniScan MX has been the most successful portable and modular phased array test instrument produced by Olympus to date, with thousands of units in use throughout the world.
-
Product
Inspection & Metrology Platform
Neon
-
Neon is Cohu’s next generation inspection platform optimized for small, fragile semiconductors used in automotive, consumer, industrial and medical, and mobility applications.
-
Product
Fiber End-Face Inspection Interferometer
CLEAVEMETER 3D
-
The CLEAVEMETER 3D™ is a non-contact interferometer designed for inspecting the end-faces of cleaved or polished optical fibers with cladding diameters of 125 µm to 1200 µm. It gives immediate and precise information on important end-face properties such as flatness, perpendicularity, hackles and dust. Based on the NYFORS CLEAVEMETER 3D™ design, in addition to producing sharp fringe patterns it also generates three-dimensional images of the cleaved fiber end.
-
Product
Magnetic Particle Inspection Systems for Non-Destructive Testing (NDT)
-
VERIFY SURFACE AND SUBSURFACE STRUCTURAL INTEGRITY IN: Industrial Crankshafts, Ferrous Parts, Aircraft Components, Landing Gear Components.
